scholarly journals Experimental and Numerical Failure Analysis of Adhesive Composite Joints

2012 ◽  
Vol 2012 ◽  
pp. 1-10 ◽  
Author(s):  
Farhad Asgari Mehrabadi
Keyword(s):  
Adhesive Bonding ◽  
Strain Energy Release ◽  
Lap Joints ◽  
Mode I ◽  
Pure Mode ◽  
Bonded Joints ◽  
Lap Joint ◽  
Stress Concentrations ◽  
Adhesively Bonded ◽  
Mode I Loading

In the first section of this work, a suitable data reduction scheme is developed to measure the adhesive joints strain energy release rate under pure mode-I loading, and in the second section, three types of adhesive hybrid lap-joints, that is, Aluminum-GFRP (Glass Fiber Reinforced Plastic), GFRP-GFRP, and Steel-GFRP were employed in the determination of adhesive hybrid joints strengths and failures that occur at these assemblies under tension loading. To achieve the aims, Double Cantilever Beam (DCB) was used to evaluate the fracture state under the mode-I loading (opening mode) and also hybrid lap-joint was employed to investigate the failure load and strength of bonded joints. The finite-element study was carried out to understand the stress intensity factors in DCB test to account fracture toughness using J-integral method as a useful tool for predicting crack failures. In the case of hybrid lap-joint tests, a numerical modeling was also performed to determine the adhesive stress distribution and stress concentrations in the side of lap-joint. Results are discussed in terms of their relationship with adhesively bonded joints and thus can be used to develop appropriate approaches aimed at using adhesive bonding and extending the lives of adhesively bonded repairs for aerospace structures.

Towards pure mode I loading in dissimilar adhesively bonded double cantilever beams

2021 ◽  
Vol 107 ◽  
pp. 102826
Author(s):  
M. Moazzami ◽  
M.R. Ayatollahi ◽  
S. Teixeira de Freitas ◽  
L.F.M. da Silva
Keyword(s):  
Mode I ◽  
Pure Mode ◽  
Cantilever Beams ◽  
Adhesively Bonded ◽  
Mode I Loading ◽  
Double Cantilever Beams

Experimental Study of Dynamic Behaviour of Aluminum/Aluminum and Composite/Composite Double Lap Joints

2011 ◽  
Vol 62 ◽  
pp. 155-163 ◽  
Author(s):  
O. Essersi ◽  
Mostapha Tarfaoui ◽  
S. Boyd ◽  
R.A. Shenoi ◽  
F. Meraghni
Keyword(s):  
Adhesive Bonding ◽  
Dynamic Behaviour ◽  
Lap Joints ◽  
High Rate ◽  
Bonded Joints ◽  
Adhesively Bonded ◽  
Adhesively Bonded Joints ◽  
Loading Rates ◽  
Structural Adhesive ◽  
Force Displacement

This paper presents an experimental investigation on the behaviour of structural adhesive bonding under quasi-static and moderately high loading rates. It addresses the effects of the loading rate on the strength of the adhesively bonded joints under dynamic tensile. A comparison has been achieved between the strength and the damage of specimens’ made of aluminium and lamina substrates. High rate tests showed ringing in the force/displacement curves.

scholarly journals Defects and uncertainties of adhesively bonded composite joints

2021 ◽  
Vol 3 (9) ◽  
Author(s):  
Sadik Omairey ◽  
Nithin Jayasree ◽  
Mihalis Kazilas
Keyword(s):  
Composite Materials ◽  
Composite Structures ◽  
Production Efficiency ◽  
Adhesive Bonding ◽  
Detection Methods ◽  
Bonded Joints ◽  
Adhesively Bonded ◽  
Adhesively Bonded Joints ◽  
Wide Range ◽  
Bonded Composite

AbstractThe increasing use of fibre reinforced polymer composite materials in a wide range of applications increases the use of similar and dissimilar joints. Traditional joining methods such as welding, mechanical fastening and riveting are challenging in composites due to their material properties, heterogeneous nature, and layup configuration. Adhesive bonding allows flexibility in materials selection and offers improved production efficiency from product design and manufacture to final assembly, enabling cost reduction. However, the performance of adhesively bonded composite structures cannot be fully verified by inspection and testing due to the unforeseen nature of defects and manufacturing uncertainties presented in this joining method. These uncertainties can manifest as kissing bonds, porosity and voids in the adhesive. As a result, the use of adhesively bonded joints is often constrained by conservative certification requirements, limiting the potential of composite materials in weight reduction, cost-saving, and performance. There is a need to identify these uncertainties and understand their effect when designing these adhesively bonded joints. This article aims to report and categorise these uncertainties, offering the reader a reliable and inclusive source to conduct further research, such as the development of probabilistic reliability-based design optimisation, sensitivity analysis, defect detection methods and process development.

Challenges in Joining Thermoset Composite Piping

2010 ◽  
Author(s):  
Avinash Parashar ◽  
Pierre Mertiny
Keyword(s):  
Adhesive Bonding ◽  
Lap Joints ◽  
Fiber Reinforced Polymers ◽  
Potential Candidate ◽  
Loading Conditions ◽  
Adhesively Bonded ◽  
Technical Literature ◽  
Filament Wound ◽  
Piping Systems ◽  
Mechanical Properties And Corrosion

The aim of this paper is to examine solutions and challenges related to joining thermoset composite piping. Fiber reinforced polymers (FRP) have been used in piping systems for more than 40 years. Higher specific mechanical properties and corrosion resistance of FRP make them a potential candidate for replacing metallic piping structures. Despite the advantages associated with FRP, their application is still limited due to, in part, unsatisfactory methods for joining composite subcomponents and inadequate knowledge of failure mechanism under different loading conditions. Adhesively bonded joints are attractive for many applications since they offer integrated sealing, minimal part count and do not require pipe extremities with complex geometries such as threads or bell and spigot configurations. So far, the majority of work reported in the technical literature on adhesively bonded pipe joints is concerned with lap joints employing wrapping techniques to produce overlap sleeve connections. More recently, a joining technique was proposed that replaces the wrapping technique with filament-wound overlap sleeve couplers that are adhesively bonded to the pipe extremities. In the present article, various joining techniques for FRP piping through adhesive bonding are discussed, and damage mechanisms under different loading conditions are examined.

Sign in / Sign up

Export Citation Format

Share Document