scholarly journals Schottky Diodes and Thin Films Based on Copolymer: Poly(aniline-co-toluidine)

2009 ◽  
Vol 2009 ◽  
pp. 1-5 ◽  
Author(s):  
A. Elmansouri ◽  
N. Hadik ◽  
A. Outzourhit ◽  
A. Lachkar ◽  
A. Abouelaoualim ◽  
...  
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Electrochemical Polymerization ◽  
Schottky Diodes ◽  
Supporting Electrolyte ◽  
Glass Substrates ◽  
Copolymer Films ◽  
Current Voltage ◽  
Copolymer Poly ◽  
Poly Aniline

Poly(aniline-co-o-toluidine) (PANI-co-POT) thin films were deposited on indium tin oxide- (ITO-) coated glass substrates by electrochemical polymerization under cyclic voltammetric conditions from aniline-co-o-toluidine monomer in an aqueous solution of HCl as a supporting electrolyte. These measurements showed that the optical band gap of the copolymer films is on the order of 2.65 eV. On the other hand, ITO/PANI-co-POT/Al devices were fabricated by thermal evaporation of Aluminum circular electrodes on the as-deposited PANI-co-POT films. The Current-Voltage characteristics of these devices are nonlinear. The diode parameters were calculated from I-V characteristics using the modified Shockley equation. The C-F characteristics were also measured.

scholarly journals Spectroscopic Characterization of Electrodeposited Poly(o-toluidine) Thin Films and Electrical Properties of ITO/Poly(o-toluidine)/Aluminum Schottky Diodes

2007 ◽  
Vol 2007 ◽  
pp. 1-7 ◽  
Author(s):  
A. Elmansouri ◽  
A. Outzourhit ◽  
A. Oueriagli ◽  
A. Lachkar ◽  
N. Hadik ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrochemical Polymerization ◽  
Schottky Diodes ◽  
Supporting Electrolyte ◽  
Spectroscopic Characterization ◽  
Current Voltage ◽  
Current Voltage Characteristics ◽  
Deposited Films ◽  
Ft Raman

Poly(o-toluidine) (POT) thin films were synthesized by electrochemical polymerization under cyclic voltammetric conditions from o-toluidine monomer in an aqueous solution of HCl as a supporting electrolyte. The electrosynthesized films were characterized by UV-Visible, FT-Raman, and FTIR spectroscopies. The optical transmissions of the as-deposited films were measured in the 400–900 nm wavelength range. These measurements showed that the optical band gap of the polymer films is in the order of 2.52 eV. The FT-Raman and FTIR measurements showed that the POT film is composed of imine and amine units. ITO/POT/Al devices were fabricated by thermal evaporation of aluminum circular contacts on films deposited on ITO-coated glass. The nonlinear current-voltage characteristics of these devices indicate a rectifying behavior. The diode parameters were calculated from I-V characteristics using the modified Shockley equation. The measured C-V and C-F characteristics are presented.

Electrochemical, optical and morphological properties of poly (N-vinylcarbazole/TiO2) and (N-vinylcarbazole/aniline)/TiO2 copolymer prepared by electrochemical polymerization

e-Polymers ◽  
2018 ◽  
Vol 18 (2) ◽  
pp. 111-122 ◽  
Author(s):  
Ouahiba Bouriche ◽  
Brahim Bouzerafa ◽  
Hicham Kouadri
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Electrochemical Polymerization ◽  
Supporting Electrolyte ◽  
Visible Region ◽  
Photovoltaic Cell ◽  
Morphological Properties ◽  
Impedance Spectroscopy Study ◽  
Before And After ◽  
Acetonitrile Solutions

AbstractPoly (N-vinylcarbazole) (PVK) and a new copolymer, PVK/polyaniline (PANI), have been successfully prepared by electrochemical polymerization of N-vinylcarbazole (NVK) and NVK/aniline from acetonitrile medium and LiClO4 supporting electrolyte. Composite thin films were studied by cyclic voltammetry (CV) in LiClO4/acetonitrile solutions on an indium tin oxide (ITO) electrode. The influences of concentration of titanium dioxide (TiO2) on the electrochemical properties of these composite materials were also investigated. The results of scanning electron microscopy (SEM) confirm the presence of TiO2 in the composite, which consequently modifies the morphology of the film significantly. Topographical analysis has shown that TiO2 nanoparticles (NPs) affect the morphology of thin films (roughness). The analysis of the voltammograms of PVK and of (PVK+PANI) before and after the addition of TiO2 at different concentrations shows a redox couple which was not observed in the absence of TiO2. The impedance spectroscopy study shows that the resistance of the PVK and (PVK+PANI) films decreases with increasing of TiO2 concentration, and this in turn contributes to a good conductivity of the film. The optical characterization of the composites has been carried out by UV-Vis absorption and photoluminescence (PL) spectroscopy and it was noted that the samples (PVK+10−2 TiO2) exhibited high transmittance (83%) in the visible region and a low gap value (2.69 eV) which confirms that this material can be used in a photovoltaic cell. This is explained by the introduction of the donor levels in the band gap of PVK by the TiO2, due to an effective doping.

Theoretical and Experimental Study of UV Detection Characteristics of Pd/ZnO Nanorod Schottky Diodes

NANO ◽  
2017 ◽  
Vol 12 (11) ◽  
pp. 1750137
Author(s):  
Shaivalini Singh ◽  
Pramod Kumar Tiwari ◽  
Hemant Kumar ◽  
Yogesh Kumar ◽  
Gopal Rawat ◽  
...  
Keyword(s):  
Experimental Study ◽  
Indium Tin Oxide ◽  
Uv Light ◽  
Schottky Diodes ◽  
Three Dimensional ◽  
Zno Nanorod ◽  
X Ray Diffraction ◽  
Sem Image ◽  
Glass Substrates ◽  
Current Voltage

In this work, we report theoretical and experimental study of Pd/ZnO nanorod (NR) Schottky diodes-based ultraviolet photodetector (UV-PD). The ZnO-NRs are deposited on indium tin oxide (ITO) coated glass substrates by using a low-temperature hydrothermal method. The surface morphology of the ZnO-NRs film is characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The SEM image shows vertically grown NRs with uniformity, and XRD shows the preferred (002) orientation of ZnO-NR films. The current–voltage characteristics of Pd/ZnO-NR Schottky diodes are studied under dark and UV light. A voltage bias from [Formula: see text]1[Formula: see text]V to [Formula: see text]1[Formula: see text]V is applied and the ratio of photocurrent to dark current was ([Formula: see text] at [Formula: see text][Formula: see text]V) calculated from the [Formula: see text]–[Formula: see text] curve. The value of responsivity was found to be 0.111[Formula: see text]A/W at [Formula: see text][Formula: see text]nm and at [Formula: see text][Formula: see text]V. An approximated UV-PD structure has also been numerically simulated using three-dimensional (3D) device simulator from Visual TCAD of Cogenda International. The simulated [Formula: see text]–[Formula: see text] characteristics have also been plotted under both dark and light conditions. The simulated results are found to be following the nature of experimental results.

scholarly journals Improving Performance of CIGS Solar Cells by Annealing ITO Thin Films Electrodes

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Chuan Lung Chuang ◽  
Ming Wei Chang ◽  
Nien Po Chen ◽  
Chung Chiang Pan ◽  
Chung Ping Liu
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Solar Cells ◽  
Indium Tin Oxide ◽  
Copper Indium Gallium Diselenide ◽  
Glass Substrates ◽  
Ito Film ◽  
Ito Thin Films ◽  
Cigs Solar Cells ◽  
Ito Films

Indium tin oxide (ITO) thin films were grown on glass substrates by direct current (DC) reactive magnetron sputtering at room temperature. Annealing at the optimal temperature can considerably improve the composition, structure, optical properties, and electrical properties of the ITO film. An ITO sample with a favorable crystalline structure was obtained by annealing in fixed oxygen/argon ratio of 0.03 at 400°C for 30 min. The carrier concentration, mobility, resistivity, band gap, transmission in the visible-light region, and transmission in the near-IR regions of the ITO sample were-1.6E+20 cm−3,2.7E+01 cm2/Vs,1.4E-03 Ohm-cm, 3.2 eV, 89.1%, and 94.7%, respectively. Thus, annealing improved the average transmissions (400–1200 nm) of the ITO film by 16.36%. Moreover, annealing a copper-indium-gallium-diselenide (CIGS) solar cell at 400°C for 30 min in air improved its efficiency by 18.75%. The characteristics of annealing ITO films importantly affect the structural, morphological, electrical, and optical properties of ITO films that are used in solar cells.

Effect of Substrate Temperature on the Electrochromic Properties of Cobalt Hydroxide Thin Films Prepared by Reactive Sputtering

2011 ◽  
Vol 1328 ◽  
Author(s):  
KyoungMoo Lee ◽  
Yoshio Abe ◽  
Midori Kawamura ◽  
Hidenobu Itoh
Keyword(s):  
Thin Films ◽  
Substrate Temperature ◽  
Indium Tin Oxide ◽  
Large Change ◽  
Amorphous Structure ◽  
Cobalt Hydroxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates ◽  
Substrate Temperatures

ABSTRACTCobalt hydroxide thin films with a thickness of 100 nm were deposited onto glass, Si and indium tin oxide (ITO)-coated glass substrates by reactively sputtering a Co target in H2O gas. The substrate temperature was varied from -20 to +200°C. The EC performance of the films was investigated in 0.1 M KOH aqueous solution. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy of the samples indicated that Co3O4 films were formed at substrate temperatures above 100°C, and amorphous CoOOH films were deposited in the range from 10 to -20°C. A large change in transmittance of approximately 26% and high EC coloration efficiency of 47 cm2/C were obtained at a wavelength of 600 nm for the CoOOH thin film deposited at -20°C. The good EC performance of the CoOOH films is attributed to the low film density and amorphous structure.

scholarly journals Opto-Electronic Properties of Epoxy/Silicone Blend Based Thin Films

2021 ◽  
Author(s):  
Younes Ziat ◽  
Hamza Belkhanchi ◽  
Maryama Hammi ◽  
Charaf Laghlimi ◽  
A Moutcine
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Optical Transition ◽  
Sol Gel ◽  
Glass Substrates ◽  
Nanostructured Thin Films ◽  
Ito Glass ◽  
Potential Applications ◽  
Optical Applications ◽  
Nitrogen Doped Carbon

Abstract Recently, the rise of two dimensional amorphous nanostructured thin films have ignited a big interest because of their intriguingly isotropic structural and physical properties leading to potential applications in the nano-optoelectronics. However, according to literature, most of optoelectronic properties are investigated on chalcogenides related heterostructures. This has motivated the present work aiming to provide a new platform for the fabrication, examination of the properties and the applications of 2D nanostructured thin films based on epoxy/silicone blend. Thin films of Epoxy/Silicone loaded with nitrogen doped carbon nanotubes (N-CNTs) were prepared by sol-gel method and deposited on Indium Tin Oxide (ITO) glass substrates at room temperature. Further examination of optical properties aimed the investigation of optical pseudo-gap and Urbach energy and enabled the determination of processed films thickness based on Manifacier and Swanepol method. The results indicated that the unloaded thin films have a direct optical transition with a value of 3.61 eV followed by noticeable shift towards narrowing gaps depending on the loading rate. Urbach's energy is 0.19 eV for the unloaded thin films, and varies from 0.43 to 1.33 eV for the loaded thin films with increasing the rate of N-CNTs. It is inversely variable with the optical pseudo-gap. Finally, Epoxy/Silicone loaded with N-CNTs nanocomposites films can be developed as active layers with specific optical characteristics, giving the possibility to be used in electro-optical applications.

Effect of Hydrogen Treatment on Room -Temperature Electric-Field Induced Properties in Narrow-Gap ZnCdHgTe Thin Films

2004 ◽  
Vol 813 ◽  
Author(s):  
Galina M. Khlyap ◽  
Petro G. Sydorchuk ◽  
Jacek Polit
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Hydrogen Treatment ◽  
Narrow Gap ◽  
Glass Substrates ◽  
Semiconductor Thin Films ◽  
Visible Wavelength Range ◽  
Current Voltage ◽  
Before And After ◽  
First Time

ABSTRACTThe effect of hydrogen treatment on room temperature electric properties of narrow-gap semiconductor thin films ZnxCdyHg1−z−yTe (0 < x < 0.50, 0.20 < y < 0.40) is investigated for the first time. ZnCdHgTe films of 2 – 5 [.proportional]m thickness were grown on glass substrates by pulsed laser deposition technique. As-grown films were thermally treated in the flow of molecular H2 at 200°C during 24 hours. Comparison between electric characteristics measured before and after hydrogenation showed sufficient changes of the film resistance and appearance of photosensitivity in the visible wavelength range. Study of current-voltage characteristics of the films revealed appearance and significant change of diode-like properties.

scholarly journals Investigating the Nanocomposite Thin Films of Hematite α-Fe2O3 and Nafion for Cholesterol Biosensing Applications

2020 ◽  
Vol 2 ◽  
Author(s):  
Indra Sulania ◽  
R. Blessy Pricilla ◽  
G. B. V. S. Lakshmi
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Differential Pulse ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Enzyme Substrate ◽  
Atomic Force ◽  
Nanocomposite Thin Films ◽  
Multi Phase ◽  
Cholesterol Biosensor

Nanocomposite materials are multi-phase materials, usually solids, which have two or more component materials having different chemical and physical properties. When blended together, a newer material is formed with distinctive properties which make them an eligible candidate for many important applications. In the present study, thin films of nafion (polymer) and hematite or α-Fe2O3 (nanoparticles) nanocomposite is fabricated on indium tin oxide (ITO) coated glass substrates, due to its enhanced ionic conductivity, for cholesterol biosensor applications. Scanning electron microscopy and Atomic force microscopy revealed the formation of nanorod structured α-Fe2O3 in the films. The cyclic voltammetry (CV) studies of nafion-α-Fe2O3/ITO revealed the redox properties of the nanocomposites. The sensing studies were performed on nafion-α-Fe2O3/CHOx/ITO bioelectrode using differential pulse voltammetry (DPV) at various concentrations of cholesterol. The enzyme immobilization leaded to the selective detection of cholesterol with a sensitivity of 64.93 × 10−2 μA (mg/dl)−1 cm−2. The enzyme substrate interaction (Michaelis–Menten) constant Km, was obtained to be 19 mg/dl.

Sign in / Sign up

Export Citation Format

Share Document