scholarly journals Mechanical Researches on Young's Modulus of SCS Nanostructures

2009 ◽  
Vol 2009 ◽  
pp. 1-6 ◽  
Author(s):  
Qinhua Jin ◽  
Tie Li ◽  
Ping Zhou ◽  
Yuelin Wang
Keyword(s):  
Young’S Modulus ◽  
Surface Effect ◽  
Young's Modulus ◽  
Tensile Tests ◽  
Testing Methods ◽  
Bending Tests ◽  
Resonance Test ◽  
Experimental Errors ◽  
The Difference ◽  
Experimental Researches

Nanostructures of SingleCrystalSilicon (SCS) with superior electrical, mechanical, thermal, and optical properties are emerging in the development of novel nanodevices. Mechanical properties especially Young's modulus are essential in developing and utilizing such nanodevices. In this paper, experimental researches including bending tests, resonance tests, and tensile tests on Young' s modulus of nanoscaled SCS are reviewed, and their results are compared. It was found that the values ofEmeasured by different testing methods cannot match to each other. As the differences cannot be explained as experimental errors, it should be understood by taking surface effect into account. With a simplified model, we qualitatively explained the difference inEvalue measured by tensile test and by resonance test for Si nanobeams.

Comparison of results obtained by static 3- and 4-point bending and flexural vibration tests on solid wood, MDF, and 5-plywood

Holzforschung ◽  
2013 ◽  
Vol 67 (8) ◽  
pp. 941-948 ◽  
Author(s):  
Hiroshi Yoshihara
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Medium Density Fiberboard ◽  
Flexural Vibration ◽  
Solid Wood ◽  
Bending Tests ◽  
Four Point Bending ◽  
Flexural Vibration Test ◽  
The Difference ◽  
Vibration Tests

Abstract The flexural Young’s modulus of western hemlock, medium-density fiberboard, and 5-plywood (made of lauan) has been determined by conducting three- and four-point bending tests with various span lengths and by flexural vibration test. The Young’s modulus was significantly influenced by the deflection measurement method. In particular, the Young’s modulus was not reliable based on the difference between the deflections at two specific points in the specimen, although this test is standardized according to ISO 3349-1975 and JIS Z2101-2009.

scholarly journals Effect of Nanopores on Mechanical Properties of the Shape Memory Alloy

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 529
Author(s):  
Chunzhi Du ◽  
Zhifan Li ◽  
Bingfei Liu
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Shape Memory ◽  
Young’S Modulus ◽  
Residual Strain ◽  
Surface Effect ◽  
Young's Modulus ◽  
Strain Curve ◽  
Stress Strain ◽  
Strength Limit

Nanoporous Shape Memory Alloys (SMA) are widely used in aerospace, military industry, medical and health and other fields. More and more attention has been paid to its mechanical properties. In particular, when the size of the pores is reduced to the nanometer level, the effect of the surface effect of the nanoporous material on the mechanical properties of the SMA will increase sharply, and the residual strain of the SMA material will change with the nanoporosity. In this work, the expression of Young’s modulus of nanopore SMA considering surface effects is first derived, which is a function of nanoporosity and nanopore size. Based on the obtained Young’s modulus, a constitutive model of nanoporous SMA considering residual strain is established. Then, the stress–strain curve of dense SMA based on the new constitutive model is drawn by numerical method. The results are in good agreement with the simulation results in the published literature. Finally, the stress-strain curves of SMA with different nanoporosities are drawn, and it is concluded that the Young’s modulus and strength limit decrease with the increase of nanoporosity.

Transverse Young's Moduli and Cell Shapes in Coniferous Early Wood

Holzforschung ◽  
2002 ◽  
Vol 56 (1) ◽  
pp. 1-6 ◽  
Author(s):  
Ugai Watanabe ◽  
Minoru Fujita ◽  
Misato Norimoto
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Bending Moment ◽  
Cell Models ◽  
Young’S Moduli ◽  
Cell Shapes ◽  
The Difference ◽  
Square Cells ◽  
Experimental Values ◽  
The Relationship

Summary The relationship between transverse Young's moduli and cell shapes in coniferous early wood was investigated using cell models constructed by two dimensional power spectrum analysis. The calculated values of tangential Young's modulus qualitatively explained the relationship between experimental values and density as well as the difference in experimental values among species. The calculated values of radial Young's modulus for the species having hexagonal cells agreed well with the experimental values, whereas, for the species having square cells, the calculated values were much larger than the experimental values. This result was ascribed to the fact that the bending moment on the radial cell wall of square cell models was calculated to be small. It is suggested that the asymmetrical shape of real wood cells or the behavior of nodes during ell deformation is an important factor in the mechanism of linear elastic deformation of wood cells.

Evaluation of Young’s modulus of RE123 bulk superconductors by three point bending tests

2006 ◽  
Vol 445-448 ◽  
pp. 422-426 ◽  
Author(s):  
T. Sato ◽  
K. Katagiri ◽  
T. Hokari ◽  
Y. Hatakeyama ◽  
A. Murakami ◽  
...  
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Bending Tests ◽  
Three Point Bending ◽  
Bulk Superconductors

Cellulose Whiskers Micro-Fibers Effect in the Mechanical Proprieties of PP and PLA Composites Fibers Obtained by Spinning Process

2011 ◽  
Vol 146 ◽  
pp. 12-26 ◽  
Author(s):  
A. Gherissi ◽  
R.Ben Cheikh ◽  
E. Dévaux ◽  
Fethi Abbassi
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Tensile Tests ◽  
Advanced Materials ◽  
Uniaxial Tensile ◽  
Failure Resistance ◽  
Cellulose Whiskers ◽  
Limit Strength

In this study, we present the manufacturing process of two new composites materials in the form of long fibers of polylactic-acid (PLA) or polypropylene (PP), reinforced by cellulose whiskers micro-fibers loads. In order to evaluate the mechanical properties of these advanced materials, a several uniaxial tensile tests were carried out. The PP and the PLA have initially been spinning without the addition of cellulose whiskers micro-fibers. In order to study the effects of cellulose whiskers micro-fibers reinforcements in the Mechanical behavior of the PLA and PP filaments, we determinate the proprieties of these advanced material from the tensile results. For the PP composite filaments material case, the whiskers reinforcement increases Young's modulus and failure resistance, but it reduces the limit strength failure. For the PLA composites the addition of 1% wt of cellulose whiskers from the total volume fraction of the material, increase the Young’s modulus more than 50% and a decrease of the failure resistance and the limit strength of composite. The obtained composites fibers are very rigid and brittle. What follows, that the addition of cellulose whiskers micro fibers in PP matrix, provides mechanical properties more convenient compared to the PLA matrix.

High Temperature Mechanical Properties of Ni-YSZ Cermets for SOFC Anode

2010 ◽  
Author(s):  
Fumitada Iguchi ◽  
Hiromichi Kitahara ◽  
Hiroo Yugami
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Strain Diagram ◽  
Thermal Cycles ◽  
High Temperature Mechanical Properties ◽  
Sofc Anode ◽  
The Difference

The mechanical properties of Ni-YSZ cermets at high temperature in reduction atmosphere were evaluated by the four points bending method. We studied the influences of reduction and thermal cycles, i.e. a cycle from R.T. to 800°C, to flexural strength and Young’s modulus. The flexural strength of Ni-YSZ at room temperature was lower than that of NiO-YSZ by about 10 to 20% mainly caused by the increment of porosity. But, the flexural strength of Ni-YSZ at 800°C was drastically decreased by an half of that at R.T. In addition, the stress–strain diagram of Ni-YSZ at 800°C indicated that it showed weak ductility. The maximum observed strain was over 0.5% at 30MPa. On the contrary, NiO-YSZ showed only brittlely at 800°C. The difference was caused by Ni metal in the Ni-YSZ cermets. Therefore, it was expected that Ni-YSZ is easily deformed in operation, though residual stress between an anode and an electrolyte was low. The influence of thermal cycles to flexural strength and Young’s modulus was not observed clearly. At the same time, the differences of microstructure were not observed. Therefore, it was concluded that the cycle does not change mechanical properties significantly.

Fibers of Bamboo and Hem Palm Tree

2001 ◽  
Vol 702 ◽  
Author(s):  
Shigeyasu Amada
Keyword(s):  
Young’S Modulus ◽  
Elastic Properties ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Simple Procedure ◽  
High Strength ◽  
Tensile Tests ◽  
Palm Tree ◽  
Bamboo Fibers ◽  
The One

ABSTRACTBamboo is a typical composite material which is axially reinforced by very strong fibers. So that, the fibers play an important role for the bamboo structure. The elastic properties of the bamboo culm have been measured only by tensile test so far, which needs a large specimen. Recently ultra-sonic technique, which has a simple procedure and uses a small specimen, has been applied to woods as well as metals. This report reviews about the elastic properties of bamboo and Hemp palm fibers. The Young's modulus and Poisson's ratio of the bamboo fibers are measured by ultra-sonic method with a transmitting wave. On the other hand, the strength of the bamboo and Hemp palm fibers are measured by the tensile tests. Using the volume fraction of fibers in the specimen and mixture principle, the Young's modulus and strength of the fibers and parenchyma were obtained. The fiber has a high strength up to 1GPa and an strong anisotropic property because its axial Young's modulus has 7 times higher than the one in the transverse direction.

Young’s Modulus of Nanohoneycomb Structures According to the Porosity

2007 ◽  
Vol 334-335 ◽  
pp. 761-764
Author(s):  
D.H. Choi ◽  
C.W. Lee ◽  
P.S. Lee ◽  
J.H. Lee ◽  
W. Hwang ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Young’S Modulus ◽  
Large Range ◽  
Young's Modulus ◽  
Vertical Direction ◽  
Moment Of Inertia ◽  
Beam Length ◽  
Bending Tests ◽  
Force Microscopy ◽  
Atomic Force

Young’s modulus of nanohoneycomb structures in the vertical direction relative to the pore (generally along the beam length) is measured according to the porosity from bending tests in atomic force microscopy (AFM). The pore diameters of the nanohoneycomb structures are from about 30 to 60 nm. To determine the Young’s modulus of the nanohoneycomb structures, the area moment of inertia of the nanohoneycomb structure is determined according to the arrangement of the pores. The area moment of inertia of the nanohoneycomb structure is found to be affected by the porosity of the nanohoneycomb structures. The Young’s modulus of the nanohoneycomb structures decreases as a function of the porosity in a large range.

scholarly journals Improving the Mechanical Properties of a β-type Ti-Nb-Zr-Fe-O Alloy

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1491 ◽  
Author(s):  
Vasile Danut Cojocaru ◽  
Anna Nocivin ◽  
Corneliu Trisca-Rusu ◽  
Alexandru Dan ◽  
Raluca Irimescu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Tensile Tests ◽  
Research Directions ◽  
Biomedical Implant ◽  
Advantages And Disadvantages ◽  
Β Phase

The influence of complex thermo-mechanical processing (TMP) on the mechanical properties of a Ti-Nb-Zr-Fe-O bio-alloy was investigated in this study. The proposed TMP program involves a schema featuring a series of severe plastic deformation (SPD) and solution treatment (STs). The purpose of this study was to find the proper parameter combination for the applied TMP and thus enhance the mechanical strength and diminish the Young’s modulus. The proposed chemical composition of the studied β-type Ti-alloy was conceived from already-appreciated Ti-Nb-Ta-Zr alloys with high β-stability by replacing the expensive Ta with more accessible Fe and O. These chemical additions are expected to better enhance β-stability and thus avoid the generation of ω, α’, and α” during complex TMP, as well as allow for the processing of a single bcc β-phase with significant grain diminution, increased mechanical strength, and a low elasticity value/Young’s modulus. The proposed TMP program considers two research directions of TMP experiments. For comparisons using structural and mechanical perspectives, the two categories of the experimental samples were analyzed using SEM microscopy and a series of tensile tests. The comparison also included some already published results for similar alloys. The analysis revealed the advantages and disadvantages for all compared categories, with the conclusions highlighting that the studied alloys are suitable for expanding the database of possible β-Ti bio-alloys that could be used depending on the specific requirements of different biomedical implant applications.

Sign in / Sign up

Export Citation Format

Share Document