scholarly journals Improving the Mechanical Properties of a β-type Ti-Nb-Zr-Fe-O Alloy

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1491 ◽  
Author(s):  
Vasile Danut Cojocaru ◽  
Anna Nocivin ◽  
Corneliu Trisca-Rusu ◽  
Alexandru Dan ◽  
Raluca Irimescu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Tensile Tests ◽  
Research Directions ◽  
Biomedical Implant ◽  
Advantages And Disadvantages ◽  
Β Phase

The influence of complex thermo-mechanical processing (TMP) on the mechanical properties of a Ti-Nb-Zr-Fe-O bio-alloy was investigated in this study. The proposed TMP program involves a schema featuring a series of severe plastic deformation (SPD) and solution treatment (STs). The purpose of this study was to find the proper parameter combination for the applied TMP and thus enhance the mechanical strength and diminish the Young’s modulus. The proposed chemical composition of the studied β-type Ti-alloy was conceived from already-appreciated Ti-Nb-Ta-Zr alloys with high β-stability by replacing the expensive Ta with more accessible Fe and O. These chemical additions are expected to better enhance β-stability and thus avoid the generation of ω, α’, and α” during complex TMP, as well as allow for the processing of a single bcc β-phase with significant grain diminution, increased mechanical strength, and a low elasticity value/Young’s modulus. The proposed TMP program considers two research directions of TMP experiments. For comparisons using structural and mechanical perspectives, the two categories of the experimental samples were analyzed using SEM microscopy and a series of tensile tests. The comparison also included some already published results for similar alloys. The analysis revealed the advantages and disadvantages for all compared categories, with the conclusions highlighting that the studied alloys are suitable for expanding the database of possible β-Ti bio-alloys that could be used depending on the specific requirements of different biomedical implant applications.

scholarly journals Kinetics of Capability Aging in Ti-13Nb-13Zr Alloy

Crystals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 693 ◽  
Author(s):  
Myoungjae Lee ◽  
In-Su Kim ◽  
Young Hoon Moon ◽  
Hyun Sik Yoon ◽  
Chan Hee Park ◽  
...  
Keyword(s):  
Mechanical Strength ◽  
Young’S Modulus ◽  
Mechanical Performance ◽  
Young's Modulus ◽  
Solution Treatment ◽  
High Strength ◽  
Biomedical Implant ◽  
13Zr Alloy ◽  
American Society ◽  
Kinetics Of

Metals for biomedical implant applications require a simultaneous achievement of high strength and low Young’s modulus from the viewpoints of mechanical properties. The American Society for Testing and Materials (ASTM) standards suggest two types of processing methods to confer such a mechanical performance to Ti-13Nb-13Zr alloy: solution treatment (ST) and capability aging (CA). This study elucidated the kinetics of CA process in Ti-13Nb-13Zr alloy. Microstructural evolution and mechanical change were investigated depending on the CA duration from 10 min to 6 h. The initial ST alloy possessed the full α′-martensitic structure, leading to a low strength, low Young’s modulus, and high ductility. Increasing CA duration increased mechanical strength and Young’s modulus in exchange for the reduction of ductility. Such a tendency is attributed to the decomposition of α′ martensite into (α+β) structure, particularly hard α precipitates. Mechanical compatibility (i.e., Young’s modulus compensated with a mechanical strength) of Ti-13Nb-13Zr alloy rarely increased by changing CA duration, suggestive of the intrinsic limit of static heat treatment.

scholarly journals Effect of Thermomechanical Treatments on the Phases, Microstructure, Microhardness and Young’s Modulus of Ti-25Ta-Zr Alloys

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3210 ◽  
Author(s):  
Pedro Akira Bazaglia Kuroda ◽  
Fernanda de Freitas Quadros ◽  
Raul Oliveira de Araújo ◽  
Conrado Ramos Moreira Afonso ◽  
Carlos Roberto Grandini
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Hot Rolling ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Alloy System ◽  
Slow Cooling ◽  
Β Phase ◽  
Transmission Electron ◽  
Hot Rolled

Titanium and its alloys currently are used as implants, possessing excellent mechanical properties (more suited than stainless steel and Co-Cr alloys), good corrosion resistance and good biocompatibility. The titanium alloy used for most biomedical applications is Ti-6Al-4V, however, studies showed that vanadium and aluminum cause allergic reactions in human tissues and neurological disorders. New titanium alloys without the presence of these elements are being studied. The objective of this study was to analyze the influence of thermomechanical treatments, such as hot-rolling, annealing and solution treatment in the structure, microstructure and mechanical properties of the Ti-25Ta-Zr ternary alloy system. The structural and microstructural analyses were performed using X-ray diffraction, as well as optical, scanning and transmission electron microscopy. The mechanical properties were analyzed using microhardness and Young’s modulus measurements. The results showed that the structure of the materials and the mechanical properties are influenced by the different thermal treatments: rapid cooling treatments (hot-rolling and solubilization) induced the formation of α” and β phases, while the treatments with slow cooling (annealing) induced the formation of martensite phases. Alloys in the hot-rolled and solubilized conditions have better mechanical properties results, such as low elastic modulus, due to retention of the β phase in these alloys.

scholarly journals First principles computation of composition dependent elastic constants of omega in titanium alloys: implications on mechanical behavior

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
R. Salloom ◽  
S. A. Mantri ◽  
R. Banerjee ◽  
S. G. Srinivasan
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
First Principles ◽  
Young's Modulus ◽  
Group Vi ◽  
Group V ◽  
Β Phase ◽  
Ti Alloys ◽  
Ω Phase ◽  
Stabilizer Concentration

AbstractFor decades the poor mechanical properties of Ti alloys were attributed to the intrinsic brittleness of the hexagonal ω-phase that has fewer than 5-independent slip systems. We contradict this conventional wisdom by coupling first-principles and cluster expansion calculations with experiments. We show that the elastic properties of the ω-phase can be systematically varied as a function of its composition to enhance both the ductility and strength of the Ti-alloy. Studies with five prototypical β-stabilizer solutes (Nb, Ta, V, Mo, and W) show that increasing β-stabilizer concentration destabilizes the ω-phase, in agreement with experiments. The Young’s modulus of ω-phase also decreased at larger concentration of β-stabilizers. Within the region of ω-phase stability, addition of Nb, Ta, and V (Group-V elements) decreased Young’s modulus more steeply compared to Mo and W (Group-VI elements) additions. The higher values of Young’s modulus of Ti–W and Ti–Mo binaries is related to the stronger stabilization of ω-phase due to the higher number of valence electrons. Density of states (DOS) calculations also revealed a stronger covalent bonding in the ω-phase compared to a metallic bonding in β-phase, and indicate that alloying is a promising route to enhance the ω-phase’s ductility. Overall, the mechanical properties of ω-phase predicted by our calculations agree well with the available experiments. Importantly, our study reveals that ω precipitates are not intrinsically embrittling and detrimental, and that we can create Ti-alloys with both good ductility and strength by tailoring ω precipitates' composition instead of completely eliminating them.

scholarly journals Tailoring a Low Young Modulus for a Beta Titanium Alloy by Combining Severe Plastic Deformation with Solution Treatment

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3467
Author(s):  
Anna Nocivin ◽  
Doina Raducanu ◽  
Bogdan Vasile ◽  
Corneliu Trisca-Rusu ◽  
Elisabeta Mirela Cojocaru ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Young Modulus ◽  
Orthopedic Implants ◽  
Beta Titanium Alloy

The present paper analyzed the microstructural characteristics and the mechanical properties of a Ti–Nb–Zr–Fe–O alloy of β-Ti type obtained by combining severe plastic deformation (SPD), for which the total reduction was of etot = 90%, with two variants of super-transus solution treatment (ST). The objective was to obtain a low Young’s modulus with sufficient high strength in purpose to use the alloy as a biomaterial for orthopedic implants. The microstructure analysis was conducted through X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) investigations. The analyzed mechanical properties reveal promising values for yield strength (YS) and ultimate tensile strength (UTS) of about 770 and 1100 MPa, respectively, with a low value of Young’s modulus of about 48–49 GPa. The conclusion is that satisfactory mechanical properties for this type of alloy can be obtained if considering a proper combination of SPD + ST parameters and a suitable content of β-stabilizing alloying elements, especially the Zr/Nb ratio.

Cellulose Whiskers Micro-Fibers Effect in the Mechanical Proprieties of PP and PLA Composites Fibers Obtained by Spinning Process

2011 ◽  
Vol 146 ◽  
pp. 12-26 ◽  
Author(s):  
A. Gherissi ◽  
R.Ben Cheikh ◽  
E. Dévaux ◽  
Fethi Abbassi
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Tensile Tests ◽  
Advanced Materials ◽  
Uniaxial Tensile ◽  
Failure Resistance ◽  
Cellulose Whiskers ◽  
Limit Strength

In this study, we present the manufacturing process of two new composites materials in the form of long fibers of polylactic-acid (PLA) or polypropylene (PP), reinforced by cellulose whiskers micro-fibers loads. In order to evaluate the mechanical properties of these advanced materials, a several uniaxial tensile tests were carried out. The PP and the PLA have initially been spinning without the addition of cellulose whiskers micro-fibers. In order to study the effects of cellulose whiskers micro-fibers reinforcements in the Mechanical behavior of the PLA and PP filaments, we determinate the proprieties of these advanced material from the tensile results. For the PP composite filaments material case, the whiskers reinforcement increases Young's modulus and failure resistance, but it reduces the limit strength failure. For the PLA composites the addition of 1% wt of cellulose whiskers from the total volume fraction of the material, increase the Young’s modulus more than 50% and a decrease of the failure resistance and the limit strength of composite. The obtained composites fibers are very rigid and brittle. What follows, that the addition of cellulose whiskers micro fibers in PP matrix, provides mechanical properties more convenient compared to the PLA matrix.

Phase Stability and Mechanical Properties of Ti-Cr-Sn-Zr Alloys Containing a Large Amount of Zr

2016 ◽  
Vol 879 ◽  
pp. 1344-1349 ◽  
Author(s):  
Yonosuke Murayama ◽  
Erdnechuluun Enkhjavkhlan ◽  
Akihiko Chiba
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Deformation Behavior ◽  
Single Phase ◽  
Young's Modulus ◽  
Martensitic Structure ◽  
Β Phase ◽  
Microstructural Transition ◽  
Zr Alloy ◽  
Zr Alloys

The Young’s modulus of Ti-Cr-Sn-Zr alloy varies with the composition of Cr, Sn and Zr, in which the elements act as β stabilizers. Some Ti-Cr-Sn-Zr alloys show very low Young’s modulus under 50GPa. The amount of Zr in alloys with very low Young's modulus increases with the decrease of Cr. We investigated the Young’s modulus and deformation behavior of Ti-xCr-Sn-Zr (x=0~1mass%) alloys containing a large amount of Zr. The quenched microstructure of Ti-Cr-Sn-Zr alloys changes from martensitic structure to β single-phase structure if the amounts of β stabilized elements are increased. The Ti-Cr-Sn-Zr alloys with compositions close to the transitional composition of microstructure from martensite to β phase show minimum Young’s modulus. The clear microstructural transition disappears and the minimum Young’s modulus increases if the amount of Cr becomes too small. In Ti-Cr-Sn-Zr alloys containing a large amount of Zr, Young’s modulus depends on β phase that is intermingled with martensite.

Mechanical Properties of Ti-Cr-Sn-Zr Alloys

2010 ◽  
Vol 638-642 ◽  
pp. 635-640 ◽  
Author(s):  
Yonosuke Murayama ◽  
Shuichi Sasaki ◽  
Hisamichi Kimura ◽  
Akihiko Chiba
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Biomedical Application ◽  
Young's Modulus ◽  
Mechanical Twinning ◽  
Β Phase ◽  
Low Modulus ◽  
Deformation Modes ◽  
Zr Alloy ◽  
Zr Alloys

Low modulus β Ti alloys are attractive for biomedical application. This work examines the mechanical properties of Ti-Cr-Sn-Zr system alloys, especially the effect of the varying alloy composition on the microstructure, the Young’s modulus and the deformation mechanism.The Young’s modulus of the alloy varies with the composition, which variation is caused mainly from the competition between the meta-stable β phase and ω phase.The deformation modes of the Ti-Cr-Sn-Zr alloy, which are the mechanical twinning, the deformation by slip and the deformation-induced transformation, also change depending on the composition of the alloy. The minimum of the Young’s modulusof the Ti-Cr-Sn-Zr alloy in this experiment was shown in the composition where the microstructure of the alloy changes from the martensitic structure to the meta-stable β structure.

Development of Biomedical Near β Titanium Alloys

2009 ◽  
Vol 618-619 ◽  
pp. 303-306 ◽  
Author(s):  
Zhen Tao Yu ◽  
Gui Wang ◽  
Xi Qun Ma ◽  
Matthew S. Dargusch ◽  
Jian Ye Han ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloys ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
High Strength ◽  
Alloy Chemistry ◽  
Solution Treated ◽  
Strength And Plasticity ◽  
Hot Rolled

The effects of alloy chemistry and heat treatment on the microstructure and mechanical properties of Ti-Nb-Zr-Mo-Sn near  type titanium alloys have been investigated. Near β titanium alloys consisting of non-toxic alloying elements Mo, Nb, Zr, Sn possess a low Young’s modulus, and moderate strength and plasticity. As the hot rolled TLM alloy (Ti-25Nb-3Zr-3Mo-2Sn) possesses high strength and low Young’s modulus a detailed investigation is performed for this alloy. Solution treatment of the hot rolled TLM alloy reduces strength and increases ductility without affecting the Young’s modulus. Ageing of the solution treated TLM alloy reduces elongation and increases the Young’s modulus with little change in strength. Both solution treated and aged conditions show features of two stage yielding associated with a strain induced martensitic transformation.

Mechanical Properties of Transparent Polycrystalline Silicon Nitride

2006 ◽  
Vol 317-318 ◽  
pp. 305-308 ◽  
Author(s):  
Rak Joo Sung ◽  
Takafumi Kusunose ◽  
Tadachika Nakayama ◽  
Yoon Ho Kim ◽  
Tohru Sekino ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Silicon Nitride ◽  
Young’S Modulus ◽  
Fracture Strength ◽  
Polycrystalline Silicon ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Β Phase ◽  
Α Phase

A novel transparent polycrystalline silicon nitride was fabricated by hot-press sintering with MgO and AlN as additives. The mixed powder with 3 wt.% MgO and 9 wt.% AlN was sintered at 1900oC for 1 hour under 30 MPa pressure in a nitrogen gas atmosphere. Transparent polycrystalline silicon nitride was successfully fabricated. The mechanical properties such as density, hardness, young’s modulus, fracture strength and fracture toughness were evaluated. The effect of α/β phase on the mechanical properties of transparent polycrystalline silicon nitride was investigated. The properties were changed depending on the amount of α/β phase. The hardness and Young's modulus increased with increasing the volume fraction of α-phase fraction as a reflection of the higher hardness of α-phase Si3N4. The fracture toughness and fracture strength decreased with decreasing the volume fraction of β-phase Si3N4.

Phase Stability and Mechanical Properties of Ti-Cr Based Alloys with Low Young’s Modulus

2010 ◽  
Vol 654-656 ◽  
pp. 2114-2117 ◽  
Author(s):  
Yonosuke Murayama ◽  
Shuichi Sasaki ◽  
Hisamichi Kimura ◽  
Akihiko Chiba
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Phase Stability ◽  
Deformation Mechanism ◽  
Young's Modulus ◽  
Deformation Behaviour ◽  
System Alloy ◽  
Β Phase ◽  
Ω Phase ◽  
Cr System

This work investigates the mechanical properties of Ti-Cr system alloys and focuses on the microstructure, the Young’s modulus, the deformation mechanism and the deformation behaviour observed in various alloy compositions. The addition of Al to the Ti-Cr system alloys greatly decreases the Young’s modulus. Addition of Al, Sn and Zr to various Ti-Cr alloys suppresses the athermal ω phase that forms during quenching from β field. A Ti-Cr system alloy with low Young’s modulus was obtained in suitable compositional combination of Cr, Zr and Sn or Al. The alloys with the composition where the quenched microstructure transits from martensite to meta-stable β phase show low Young’s modulus. In addition, the alloys show two-step yielding due to stress-induced transformation.

Sign in / Sign up

Export Citation Format

Share Document