Heating Rates for a Beat Frequency Laser Heated Plasma

1975 ◽  
Vol 53 (23) ◽  
pp. 2606-2610 ◽  
Author(s):  
C. E. Capjack ◽  
C. R. James
Keyword(s):  
Heating Rate ◽  
Plasma Density ◽  
Beat Frequency ◽  
Laser Beams ◽  
Magnetized Plasmas ◽  
Heating Rates ◽  
Mixing Angle ◽  
Frequency Laser ◽  
Laser Heated ◽  
Frequency Harmonic

The heating of magnetized plasmas through the utilization of a beat frequency harmonic which is excited at a frequency near to that of a Langmuir mode in the plasma is examined. Heating rates are obtained for plasmas with temperatures in the range 1 eV to 10 000 eV. In addition, the effects of the plasma density and the mixing angle of the laser beams on the heating rate will be examined.

MHD simulation of a beat frequency heated plasma

1976 ◽  
Vol 54 (21) ◽  
pp. 2140-2146 ◽  
Author(s):  
R. D. Milroy ◽  
C. E. Capjack ◽  
C. R. James ◽  
J. N. McMullin
Keyword(s):  
Exact Solution ◽  
Heating Rate ◽  
Plasma Density ◽  
Beat Frequency ◽  
Computer Code ◽  
Mhd Equations ◽  
Mhd Simulation ◽  
One Dimensional ◽  
Heating Scheme ◽  
Frequency Harmonic

The heating of a plasma in a solenoid, with a beat frequency harmonic which is excited at a frequency near to that of a Langmuir mode in a plasma, is examined. It is shown that at high temperatures the heating rate is very insensitive to changes in plasma density. The amount of energy that can be coupled to a plasma in a solenoid with this heating scheme is investigated by using a one-dimensional computer code which incorporates an exact solution of the relevant MHD equations. The absorption of energy from a high powered laser is shown to be significantly enhanced with this process.

Maximum heating rates for producing undistorted glassy carbon ware determined by wedge-shaped samples

1996 ◽  
Vol 11 (9) ◽  
pp. 2368-2375 ◽  
Author(s):  
Hossein Maleki ◽  
Lawrence R. Holland ◽  
Gwyn M. Jenkins ◽  
R. L. Zimmerman ◽  
Wally Porter
Keyword(s):  
Heating Rate ◽  
Treatment Process ◽  
Gaseous Product ◽  
Pyrolysis Mass Spectrometry ◽  
Heating Rates ◽  
Gaseous Products ◽  
Volatile Products ◽  
Solid Bodies ◽  
Polymeric Carbon ◽  
Maximum Heating

Polymeric carbon artifacts are particularly difficult to make in thick section. Heating rate, temperature, and sample thickness determine the outcome of carbonization of resin leading to a glassy polymeric carbon ware. Using wedge-shaped samples, we found the maximum thickness for various heating rates during gelling (300 K–360 K), curing (360 K–400 K), postcuring (400 K–500 K), and precarbonization (500 K–875 K). Excessive heating rate causes failure. In postcuring the critical heating rate varies inversely as the fifth power of thickness; in precarbonization this varies inversely as the third power of thickness. From thermogravimetric evidence we attribute such failure to low rates of diffusion of gaseous products of reactions occurring within the solid during pyrolysis. Mass spectrometry shows the main gaseous product is water vapor; some carboniferous gases are also evolved during precarbonization. We discuss a diffusion model applicable to any heat-treatment process in which volatile products are removed from solid bodies.

scholarly journals Towards a better representation of the solar cycle in general circulation models

2007 ◽  
Vol 7 (20) ◽  
pp. 5391-5400 ◽  
Author(s):  
K. M. Nissen ◽  
K. Matthes ◽  
U. Langematz ◽  
B. Mayer
Keyword(s):  
Solar Cycle ◽  
Heating Rate ◽  
General Circulation ◽  
Temperature Response ◽  
General Circulation Models ◽  
Short Wave ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Heating Rates ◽  
Radiation Scheme

Abstract. We introduce the improved Freie Universität Berlin (FUB) high-resolution radiation scheme FUBRad and compare it to the 4-band standard ECHAM5 SW radiation scheme of Fouquart and Bonnel (FB). Both schemes are validated against the detailed radiative transfer model libRadtran. FUBRad produces realistic heating rate variations during the solar cycle. The SW heating rate response with the FB scheme is about 20 times smaller than with FUBRad and cannot produce the observed temperature signal. A reduction of the spectral resolution to 6 bands for solar irradiance and ozone absorption cross sections leads to a degradation (reduction) of the solar SW heating rate signal by about 20%. The simulated temperature response agrees qualitatively well with observations in the summer upper stratosphere and mesosphere where irradiance variations dominate the signal. Comparison of the total short-wave heating rates under solar minimum conditions shows good agreement between FUBRad, FB and libRadtran up to the middle mesosphere (60–70 km) indicating that both parameterizations are well suited for climate integrations that do not take solar variability into account. The FUBRad scheme has been implemented as a sub-submodel of the Modular Earth Submodel System (MESSy).

INVESTIGATION OF THERMAL DEGRADATION OF POULTRY PROCESSING DEWATERED SLUDGE USING THERMOGRAVIMETRIC ANALYSIS METHOD

2015 ◽  
Vol 76 (5) ◽  
Author(s):  
N. Aniza ◽  
S. Hassan ◽  
M. F. M. Nor ◽  
K. E. Kee ◽  
Aklilu T.
Keyword(s):  
Particle Size ◽  
Thermogravimetric Analysis ◽  
Thermal Degradation ◽  
Heating Rate ◽  
Degradation Process ◽  
Heating Rates ◽  
Initial Stage ◽  
Poultry Processing ◽  
Effect Of Particle Size ◽  
Dewatered Sludge

Thermal degradation of Poultry Processing Dewatered Sludge (PPDS) was studied using thermogravimetric analysis (TGA) method. The effect of particle size on PPDS samples and operational condition such as heating rates were investigated. The non-isothermal TGA was run under a constant flow of oxygen at a rate of 30 mL/min with temperature ranging from 30ºC to 800ºC. Four sample particle sizes ranging between 0.425 mm to 2 mm, and heating rate between 5 K/min to 20 K/min were used in this study. The TGA results showed that particle size does not have any significant effect on the thermogravimetry (TG) curves at the initial stage, but the TG curves started to separate explicitly at the second stage. Particle size may affect the reactivity of sample and combustion performance due to the heat transfer and temperature gradient. The TG and peak of derivative thermogravimetry (DTG) curves tend to alter at high temperature when heating rate is increased most likely due to the limitation of mass transfer and the delay of degradation process. 

scholarly journals Self-Focusing of Hermite-Cosh-Gaussian Laser Beams in Plasma under Density Transition

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Manzoor Ahmad Wani ◽  
Niti Kant
Keyword(s):  
Laser Beam ◽  
Plasma Density ◽  
Focal Spot ◽  
Beam Width ◽  
Spot Size ◽  
Laser Beams ◽  
Equation Approach ◽  
Focal Spot Size ◽  
Self Focusing ◽  
Small Spot

Self-focusing of Hermite-Cosh-Gaussian (HChG) laser beam in plasma under density transition has been discussed here. The field distribution in the medium is expressed in terms of beam-width parameters and decentered parameter. The differential equations for the beam-width parameters are established by a parabolic wave equation approach under paraxial approximation. To overcome the defocusing, localized upward plasma density ramp is considered, so that the laser beam is focused on a small spot size. Plasma density ramp plays an important role in reducing the defocusing effect and maintaining the focal spot size up to several Rayleigh lengths. To discuss the nature of self-focusing, the behaviour of beam-width parameters with dimensionless distance of propagation for various values of decentered parameters is examined by numerical estimates. The results are presented graphically and the effect of plasma density ramp and decentered parameter on self-focusing of the beams has been discussed.

scholarly journals Effect of heating rates on the microstructure and gas permeation properties of carbon membranes

2018 ◽  
Vol 14 (3) ◽  
pp. 378-381
Author(s):  
Norazlianie Sazali ◽  
Wan Norharyati Wan Salleh ◽  
Ahmad Fauzi Ismail ◽  
Kumaran Kadirgama ◽  
Mohamad Shahrizan Moslan ◽  
...  
Keyword(s):  
Heating Rate ◽  
High Performance ◽  
Room Temperature ◽  
Gas Permeation ◽  
Carbon Membrane ◽  
Heating Rates ◽  
Polymer Blending ◽  
Carbon Membranes ◽  
Permeation Properties ◽  
Fine Turning

High performance tubular carbon membrane (TCM’s) for CO2 separation were prepared by controlling the carbonization heating rates in range of 1-7 oC/min carbonized at 800 oC under Argon environment. A single permeation apparatus was used to determine the gas permeation properties of the membrane at room temperature. Fine turning of the carbonization condition was necessary to obtain the desired permeation properties. The preparation of PI/NCC-based TCM at low heating rate caused the gas permeance for the examined gas N2 and CO2 decreased whereas the selectivity of CO2/N2 increased. It was also identified that the gas permeation properties of the resultant TCM and its structure was highly affected by the heating rate. The best carbonization heating rate was found at 3oC/min for the fabrication of TCM derived via polymer blending of PI/NCC for CO2/N2 separation.

scholarly journals Synthesis and characterization of a new conjugated polymer containing bithiazole group and its thermal decomposition kinetics

2020 ◽  
Vol 39 (2) ◽  
pp. 227
Author(s):  
Adnan Kurt ◽  
Hacer Andan ◽  
Murat Koca
Keyword(s):  
Thermal Decomposition ◽  
Heating Rate ◽  
Conjugated Polymer ◽  
Three Dimensional ◽  
Heating Rates ◽  
Diffusion Type ◽  
Optimum Heating ◽  
Rate Loss ◽  
Kinetics Of

A new conjugated polymer containing a bithiazole group is prepared by the polycondensation of 2,2'-diamino-4,4'-bithiazole and terephthaldialdehyde in the presence of glacial acetic acid. The kinetics of thermal degradation of the new polymer are investigated by thermogravimetric analysis at different heating rates. The temperature corresponding to the maximum rate loss shifts to higher temperatures with increasing heating rate. The thermal decomposition activation energies of the conjugated polymer in a conversion range of 3–15 % are 288.4 and 281.1 kJ/mol by the Flynn–Wall–Ozawa and Kissinger methods, respectively. The Horowitz–Metzger method shows that the thermodegradation mechanism of the conjugated polymer proceeds over a three-dimensional diffusion type deceleration D3 mechanism. The optimum heating rate is 20 ºC/min.

scholarly journals Investigation of Primary Recrystallization and Decarbonization with Different Heating Rates of Intermediate Annealing Using Nb-Containing Grain-Oriented Silicon Steel

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1655
Author(s):  
Xin Tian ◽  
Shuang Kuang ◽  
Jie Li ◽  
Jing Guo ◽  
Yunli Feng
Keyword(s):  
Heating Rate ◽  
Electron Backscatter Diffraction ◽  
Optical Microscope ◽  
Primary Recrystallization ◽  
Silicon Steel ◽  
Intermediate Annealing ◽  
Heating Rates ◽  
Average Grain Size ◽  
The Matrix ◽  
20 Nm

An Nb-containing grain-oriented silicon steel was produced through double-stage cold rolling in order to investigate the effect of the heating rate during intermediate annealing on primary recrystallization and decarburization behavior. The microstructure and texture were observed and analyzed by an optical microscope and an electron backscatter diffraction system. A transmission electron microscope was used to observe the precipitation behavior of inhibitors. The decarburization effect during intermediate annealing was also calculated and discussed. The results show that primary recrystallization takes place after intermediate annealing. As the heating rate increases, the average grain size decreases gradually. The textures of {411}<148> and {111}<112> were found to be the strongest along the thickness direction in all of the annealed specimens and are mainly surrounded by HEGB and HAGB (> 45°). A large number of inhibitors with the size of 14~20 nm precipitate are distributed evenly in the matrix. The above results indicate that the higher heating rate during intermediate annealing contributes to both an excellent microstructure and magnetic properties. From the calculation, as the heating rate increases, decarbonization tends to proceed in the insulation stage, and the total amount of carbonization declines.

Heating rates are more strongly influenced by near-infrared than visible reflectance in beetles

2021 ◽  
Author(s):  
Lu-Yi Wang ◽  
Amanda M. Franklin ◽  
Jay R. Black ◽  
Devi Stuart-Fox
Keyword(s):  
Heating Rate ◽  
Near Infrared ◽  
Radiative Heat ◽  
Effective Area ◽  
Morphological Properties ◽  
Heating Rates ◽  
Heat Gain ◽  
Thermal Chamber ◽  
Infrared Wavelengths ◽  
Cuticle Thickness

Adaptations to control heat transfer through the integument are a key component of temperature regulation in animals. However, there remain significant gaps in our understanding of how different optical and morphological properties of the integument affect heating rates. To address these gaps, we examined the effect of reflectivity in both ultraviolet-visible and near-infrared wavelengths, surface micro-sculpturing, effective area (area subjected to illumination) and cuticle thickness on radiative heat gain in jewel beetles (Buprestidae). We measured heating rate using a solar simulator to mimic natural sunlight, a thermal chamber to control the effects of conduction and convection, and optical filters to isolate different wavelengths. We found that effective area and reflectivity predicted heating rate. The thermal effect of reflectivity was driven by variation in near-infrared rather than ultraviolet-visible reflectivity. By contrast, cuticle thickness and surface rugosity had no detectable effect. Our results provide empirical evidence that near-infrared reflectivity has an important effect on radiative heat gain. Modulating reflectance of near-infrared wavelengths of light may be a more widespread adaptation to control heat gain than previously appreciated.

scholarly journals Measurement and Evaluation of Calorimetric Descriptors for the Suitability for Evolutionary High-Throughput Material Development

Metals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 149 ◽  
Author(s):  
Anastasiya Toenjes ◽  
Heike Sonnenberg ◽  
Christina Plump ◽  
Rolf Drechsler ◽  
Axel von Hehl
Keyword(s):  
Heating Rate ◽  
High Throughput ◽  
Macro Level ◽  
Heating Rates ◽  
Scanning Calorimetry ◽  
Characterization Methods ◽  
Material Development ◽  
First Results ◽  
Novel Method ◽  
Measurement And Evaluation

A novel method for evolutionary material development by using high-throughput processing is established. For the purpose of this high-throughput approach, spherical micro samples are used, which have to be characterized, up-scaled to macro level and valued. For the evaluation of the microstructural state of the micro samples and the associated micro-properties, fast characterization methods based on physical testing methods such as calorimetry and universal microhardness measurements are developed. Those measurements result in so-called descriptors. The increase in throughput during calorimetric characterization using differential scanning calorimetry is achieved by accelerating the heating rate. Consequently, descriptors are basically measured in a non-equilibrium state. The maximum heating rate is limited by the possibility to infer the microstructural state from the calorimetric results. The substantial quality of the measured descriptors for micro samples has to be quantified and analyzed depending on the heating rate. In this work, the first results of the measurements of calorimetric descriptors with increased heating rates for 100Cr6 will be presented and discussed. The results of low and high heating rates will be compared and analyzed using additional microhardness measurements. Furthermore, the validation of the method regarding the suitability for the evolutionary material development includes up-scaling to macro level and therefore different sample masses will be investigated using micro and macro samples during calorimetry.

Sign in / Sign up

Export Citation Format

Share Document