Experimental and theoretical basis of Lamb waves and their applications in material sciences

2007 ◽  
Vol 85 (7) ◽  
pp. 707-731 ◽  
Author(s):  
J Sadler ◽  
R Gr Maev
Keyword(s):  
Material Characterization ◽  
Guided Waves ◽  
Recent Literature ◽  
Lamb Waves ◽  
Flaw Detection ◽  
Theoretical Work ◽  
Guided Wave ◽  
Bulk Wave ◽  
Material Sciences ◽  
The Subject

The subject of Lamb waves contains a vast field of literature comprising many individual topics, with the current focus being the effective creation and use of Lamb waves in the fields of material characterization and nondestructive evaluation (NDE). This review chooses to focus on the more recent literature dealing with Lamb waves, giving introductions to a variety of topics. Because of the large amount of literature dealing with Lamb waves, many of the sections of this paper could themselves be expanded into their own literature review. This review begins with a brief introduction of Lamb waves comparing them to the acoustic bulk wave, and Rayleigh wave, and outlines the physics of a guided wave. It discusses the advantages of using guided waves, and theoretical techniques to model Lamb waves. In addition, the review discusses some of the various methods for the detection and creation of Lamb waves; techniques to detect, identify, and extract the mode from the acoustic signal; the use of Lamb waves in material characterization; flaw detection and flaw measurement; and finally examines the scattering of Lamb waves at plate ends and joints. While much of this work is experimentally based in nature, this review has attempted to also include theoretical work when possible. PACS Nos.: 43.90.+v, 81.70.Cv

scholarly journals Comparison of Ultrasonic Non-Contact Air-Coupled Techniques for Characterization of Impact-Type Defects in Pultruded GFRP Composites

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1058
Author(s):  
Aadhik Asokkumar ◽  
Elena Jasiūnienė ◽  
Renaldas Raišutis ◽  
Rymantas Jonas Kažys
Keyword(s):  
Guided Waves ◽  
Lamb Waves ◽  
Tomographic Reconstruction ◽  
Guided Wave ◽  
Reconstruction Technique ◽  
Bulk Wave ◽  
Glass Fiber Reinforced Plastic ◽  
Ultrasonic Guided Wave ◽  
Single Side ◽  
Numerical Finite Element

This article compares different air-coupled ultrasonic testing methods to characterize impact-type defects in a pultruded quasi-isotropic glass fiber-reinforced plastic (GFRP) composite plate. Using the air-coupled transducers, comparisons among three methods were performed, namely, bulk-wave through transmission, single-side access using guided waves, and ultrasonic-guided wave tomography. The air coupled through transmission technique can determine the size and shape of impact-type defects with a higher resolution, but with the consequence of time consumption and, more importantly, the necessity of access to both sides of the sample. The guided wave technique on the other hand, allows a single-side inspection and is relatively fast. It can be used to determine the size of the defect using ultrasonic B-scan, but the exact shape of the defect will be compromised. Thus, in this article, to determine the shape of the defect, application of the parallel beam tomographic reconstruction technique using guided Lamb waves is demonstrated. Furthermore, a numerical finite element simulation was performed to study the effects of guided wave propagation in the composite sample and interaction with the internal defect. Lastly, the results from the experiments of different techniques were compared according to possibilities of defect sizing and determination of its shape.

Inspection of Concrete-Metal Rod Interface Using Guided Waves

2000 ◽  
Author(s):  
Won-Bae Na ◽  
Tribikram Kundu ◽  
Mohammad R. Ehsani
Keyword(s):  
Lamb Wave ◽  
Guided Waves ◽  
Lamb Waves ◽  
Guided Wave ◽  
Ultrasonic Transducers ◽  
Interface Debonding ◽  
Long Distance ◽  
Steel Rebar ◽  
Steel Bars ◽  
Steel Rebars

Abstract The feasibility of detecting interface degradation and separation of steel rebars in concrete beams using Lamb waves is investigated in this paper. It is shown that Lamb waves can easily detect these defects. A special coupler between the steel rebar and ultrasonic transducers has been used to launch non-axisymmetric guided waves in the steel rebar. This investigation shows that the Lamb wave inspection technique is an efficient and effective tool for health monitoring of reinforced concrete structures because the Lamb wave can propagate a long distance along the reinforcing steel bars embedded in concrete as the guided wave and is sensitive to the interface debonding between the steel rebar and concrete.

Early Fatigue Damage Evaluation of Nonlinear Guided Wave Imaging in Hyperelastic Materials

2021 ◽  
Author(s):  
Chengwei Zhao ◽  
Sunia Tanweer ◽  
Jian Li ◽  
Min Lin ◽  
Xiang Zhang ◽  
...  
Keyword(s):  
Fatigue Damage ◽  
Guided Waves ◽  
Lamb Waves ◽  
Tone Burst ◽  
Guided Wave ◽  
Third Order ◽  
Hyperelastic Materials ◽  
Third Order Elastic Constants ◽  
Wave Imaging ◽  
Processing Platform

Abstract Nonlinear ultrasonic guided waves have superior sensitivity of the early fatigue damage. This paper investigates the analysis of the second harmonics of Lamb waves in a free boundary aluminum plate, and the internal resonance conditions between the Lamb wave primary modes and the second harmonics. The Murnaghan’s model is implemented in a finite element (FE) analysis to describe the hyperelastic constitutive relation for nonlinear acoustic modeling. The second harmonics of s0 mode are actuated by a 60kHz Hanning-windowed tone burst. A guided wave signal processing platform is developed for tomographic imaging. The different stages of fatigue are reflected by the changes of third-order elastic constants (TOECs) in Murnaghan’s model. The reconstructed damage locations match well with the actual ones cross different degrees and depths of fatigue.

scholarly journals Warped Wigner-Hough Transform for Defect Reflection Enhancement in Ultrasonic Guided Wave Monitoring

2012 ◽  
Vol 2012 ◽  
pp. 1-15 ◽  
Author(s):  
Luca De Marchi ◽  
Emanuele Baravelli ◽  
Giampaolo Cera ◽  
Nicolò Speciale ◽  
Alessandro Marzani
Keyword(s):  
Hough Transform ◽  
Guided Waves ◽  
Lamb Waves ◽  
Guided Wave ◽  
Nonlinear Signal Processing ◽  
Localization Accuracy ◽  
Time Frequency ◽  
Ultrasonic Guided Wave ◽  
Inspection Systems ◽  
Nonlinear Signal

To improve the defect detectability of Lamb wave inspection systems, the application of nonlinear signal processing was investigated. The approach is based on a Warped Frequency Transform (WFT) to compensate the dispersive behavior of ultrasonic guided waves, followed by a Wigner-Ville time-frequency analysis and the Hough Transform to further improve localization accuracy. As a result, an automatic detection procedure to locate defect-induced reflections was demonstrated and successfully tested by analyzing numerically simulated Lamb waves propagating in an aluminum plate. The proposed method is suitable for defect detection and can be easily implemented for real-world structural health monitoring applications.

Flaw Detection in Aluminum Plate by Shear Horizontal Guided Wave Based on Magnetostriction EMAT

2014 ◽  
Vol 614 ◽  
pp. 287-290
Author(s):  
Le Chen ◽  
Yue Min Wang ◽  
Hai Quan Geng
Keyword(s):  
Guided Waves ◽  
Flaw Detection ◽  
Test Sample ◽  
Guided Wave ◽  
Sh Waves ◽  
Electromagnetic Acoustic Transducers ◽  
Acoustic Transducers ◽  
Non Destructive ◽  
Viable Method ◽  
Shear Horizontal

Shear horizontal (SH) guided waves have been proved to be a viable method in the Non-Destructive Evaluation (NDE). Electromagnetic acoustic transducers (EMAT) can excite SH waves easily. By bonding the Fe-Co alloy to the test sample, the SH guided waves based on magnetostriction effect can be used to detect the flaw in nonferromagnetic material. The principle of exciting and receiving SH waves is introduced, and an experiment is carried out to validate the result.

scholarly journals Nonlinear Guided Wave Tomography for Detection and Evaluation of Early-Life Material Degradation in Plates

Sensors ◽  
2021 ◽  
Vol 21 (16) ◽  
pp. 5498
Author(s):  
Chengwei Zhao ◽  
Sunia Tanweer ◽  
Jian Li ◽  
Min Lin ◽  
Xiang Zhang ◽  
...  
Keyword(s):  
Early Life ◽  
Guided Waves ◽  
Lamb Waves ◽  
Tone Burst ◽  
Guided Wave ◽  
Material Degradation ◽  
Third Order Elastic Constants ◽  
Metal Plates ◽  
Wave Tomography ◽  
Aluminum Plates

In this paper, the possibility of using nonlinear ultrasonic guided waves for early-life material degradation in metal plates is investigated through both computational modeling and study. The analysis of the second harmonics of Lamb waves in a free boundary aluminum plate, and the internal resonance conditions between the Lamb wave primary modes and the second harmonics are investigated. Subsequently, Murnaghan’s hyperelastic model is implemented in a finite element (FE) analysis to study the response of aluminum plates subjected to a 60 kHz Hanning-windowed tone burst. Different stages of material degradation are reflected as the changes in the third order elastic constants (TOECs) of the Murnaghan’s model. The reconstructed degradations match the actual ones well across various degrees of degradation. The effects of several relevant factors on the accuracy of reconstructions are also discussed.

scholarly journals Attenuation of a Slow Subsonic A0 Mode Ultrasonic Guided Wave in Thin Plastic Films

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1648 ◽  
Author(s):  
Rymantas Kažys ◽  
Reimondas Šliteris ◽  
Liudas Mažeika ◽  
Olgirdas Tumšys ◽  
Egidijus Žukauskas
Keyword(s):  
Guided Waves ◽  
High Efficiency ◽  
Lamb Waves ◽  
Ultrasonic Transducer ◽  
Plane Waves ◽  
Ultrasound Velocity ◽  
Guided Wave ◽  
Low Frequencies ◽  
Plastic Films ◽  
Thin Plastic

The ultrasonic testing technique using Lamb waves is widely used for the non-destructive testing and evaluation of various structures. For air-coupled excitation and the reception of A0 mode Lamb waves, leaky guided waves are usually exploited. However, at low frequencies (<100 kHz), the velocity of this mode in plastic and composite materials can become slower than the ultrasound velocity in air, and its propagation in films is accompanied only by an evanescent wave in air. To date, the information about the attenuation of the slow A0 mode is very contradictory. Therefore, the objective of this investigation was the measurement of the attenuation of the slow A0 mode in thin plastic films. The measurement of the attenuation of normal displacements of the film caused by a propagating slow A0 mode is discussed. The normal displacements of the film at different distances from the source were measured by a laser interferometer. In order to reduce diffraction errors, the measurement method based on the excitation of cylindrical but not plane waves was proposed. The slow A0 mode was excited in the polyvinylchloride film by a dry contact type ultrasonic transducer made of high-efficiency PMN-32%PT strip-like piezoelectric crystal. It was found that that the attenuation of the slow A0 mode in PVC film at the frequency of 44 kHz is 2 dB/cm. The obtained results can be useful for the development of quality control methods for plastic films.

scholarly journals Ultrasonic Methods

2021 ◽  
pp. 87-131
Author(s):  
Vykintas Samaitis ◽  
Elena Jasiūnienė ◽  
Pawel Packo ◽  
Damira Smagulova
Keyword(s):  
Long Range ◽  
Guided Waves ◽  
Structural Integrity ◽  
Ultrasonic Inspection ◽  
Guided Wave ◽  
Ultrasonic Waves ◽  
Bulk Wave ◽  
Destructive Testing ◽  
Fibre Breakage ◽  
Ultrasonic Methods

AbstractUltrasonic inspection is a well recognized technique for non-destructive testing of aircraft components. It provides both local highly sensitive inspection in the vicinity of the sensor and long-range structural assessment by means of guided waves. In general, the properties of ultrasonic waves like velocity, attenuation and propagation characteristics such as reflection, transmission and scattering depend on composition and structural integrity of the material. Hence, ultrasonic inspection is commonly used as a primary tool for active inspection of aircraft components such as engine covers, wing skins and fuselages with the aim to detect, localise and describe delaminations, voids, fibre breakage and ply waviness. This chapter mainly focuses on long range guided wave structural health monitoring, as aircraft components require rapid evaluation of large components preferably in real time without the necessity for grouding of an aircraft. In few upcoming chapters advantages and shortcommings of bulk wave and guided wave ultrasonic inspection is presented, fundamentals of guided wave propagation and damage detection are reviewed, the reliability of guided wave SHM is discussed and some recent examples of guided wave applications to SHM of aerospace components are given.

scholarly journals Core–skin debonding detection in honeycomb sandwich structures through guided wave wavefield analysis

2018 ◽  
Vol 30 (9) ◽  
pp. 1306-1317 ◽  
Author(s):  
Lingyu Yu ◽  
Zhenhua Tian ◽  
Xiaopeng Li ◽  
Rui Zhu ◽  
Guoliang Huang
Keyword(s):  
Guided Waves ◽  
Sandwich Structures ◽  
Lamb Waves ◽  
Laser Doppler Vibrometer ◽  
Low Frequency ◽  
Guided Wave ◽  
Honeycomb Sandwich ◽  
Debonding Detection ◽  
The Waves ◽  
Detection And Quantification

Ultrasonic guided waves have proven to be an effective and efficient method for damage detection and quantification in various plate-like structures. In honeycomb sandwich structures, wave propagation and interaction with typical defects such as hidden debonding damage are complicated; hence, the detection of defects using guided waves remains a challenging problem. The work presented in this article investigates the interaction of low-frequency guided waves with core–skin debonding damage in aluminum core honeycomb sandwich structures using finite element simulations. Due to debonding damage, the waves propagating in the debonded skin panel change to fundamental antisymmetric Lamb waves with different wavenumber values. Exploiting this mechanism, experimental inspection using a non-contact laser Doppler vibrometer was performed to acquire wavefield data from pristine and debonded structures. The data were then processed and analyzed with two wavefield data–based imaging approaches, the filter reconstruction imaging and the spatial wavenumber imaging. Both approaches can clearly indicate the presence, location, and size of the debonding in the structures, thus proving to be effective methods for debonding detection and quantification for honeycomb sandwich structures.

NUMERICAL MODELING OF WALL THINNING DEFECTS CHARACTERIZATION: APPLICATIONS IN LAMB WAVE GENERATION AND INTERACTION

2008 ◽  
Vol 22 (11) ◽  
pp. 935-940
Author(s):  
HYUNJO JEONG ◽  
SEUNG-SEOK LEE ◽  
YOUNG-GIL KIM
Keyword(s):  
Guided Waves ◽  
Lamb Waves ◽  
Mode Conversion ◽  
Wave Interaction ◽  
Guided Wave ◽  
Destructive Interference ◽  
Wall Thinning ◽  
Mode Dispersion ◽  
Periodic Ring ◽  
Axisymmetric Scattering

The generation of axisymmetric Lamb waves and interaction with wall thinning (corrosion) defects in hollow cylinders are simulated using the finite element method. Guided wave interaction with defects in cylinders is challenged by the multi-mode dispersion and the mode conversion. In this paper, two longitudinal, axisymmetric modes are generated using the concept of a time-delay periodic ring arrays (TDPRA), which makes use of the constructive/destructive interference concept to achieve the unidirectional emission and reception of guided waves. The axisymmetric scattering by the wall thinning extending in full circumference of a cylinder is studied with a two-dimensional FE simulation. The effect of wall thinning depth, axial extension, and the edge shape on the reflections of guided waves is discussed.

Sign in / Sign up

Export Citation Format

Share Document