scholarly journals Attenuation of a Slow Subsonic A0 Mode Ultrasonic Guided Wave in Thin Plastic Films

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1648 ◽  
Author(s):  
Rymantas Kažys ◽  
Reimondas Šliteris ◽  
Liudas Mažeika ◽  
Olgirdas Tumšys ◽  
Egidijus Žukauskas
Keyword(s):  
Guided Waves ◽  
High Efficiency ◽  
Lamb Waves ◽  
Ultrasonic Transducer ◽  
Plane Waves ◽  
Ultrasound Velocity ◽  
Guided Wave ◽  
Low Frequencies ◽  
Plastic Films ◽  
Thin Plastic

The ultrasonic testing technique using Lamb waves is widely used for the non-destructive testing and evaluation of various structures. For air-coupled excitation and the reception of A0 mode Lamb waves, leaky guided waves are usually exploited. However, at low frequencies (<100 kHz), the velocity of this mode in plastic and composite materials can become slower than the ultrasound velocity in air, and its propagation in films is accompanied only by an evanescent wave in air. To date, the information about the attenuation of the slow A0 mode is very contradictory. Therefore, the objective of this investigation was the measurement of the attenuation of the slow A0 mode in thin plastic films. The measurement of the attenuation of normal displacements of the film caused by a propagating slow A0 mode is discussed. The normal displacements of the film at different distances from the source were measured by a laser interferometer. In order to reduce diffraction errors, the measurement method based on the excitation of cylindrical but not plane waves was proposed. The slow A0 mode was excited in the polyvinylchloride film by a dry contact type ultrasonic transducer made of high-efficiency PMN-32%PT strip-like piezoelectric crystal. It was found that that the attenuation of the slow A0 mode in PVC film at the frequency of 44 kHz is 2 dB/cm. The obtained results can be useful for the development of quality control methods for plastic films.

scholarly journals Numerical Investigation of Excitation of Various Lamb Waves Modes in Thin Plastic Films

2022 ◽  
Vol 12 (2) ◽  
pp. 849
Author(s):  
Rymantas Jonas Kazys ◽  
Justina Sestoke ◽  
Egidijus Zukauskas
Keyword(s):  
Numerical Investigation ◽  
Lamb Wave ◽  
Guided Waves ◽  
Phased Array ◽  
Ultrasonic Transducer ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Plastic Films ◽  
Thin Plastic ◽  
Wave Modes

Ultrasonic-guided waves are widely used for the non-destructive testing and material characterization of plates and thin films. In the case of thin plastic polyvinyl chloride (PVC), films up to 3.2 MHz with only two Lamb wave modes, antisymmetrical A0 and symmetrical S0, may propagate. At frequencies lower that 240 kHz, the velocity of the A0 mode becomes slower than the ultrasonic velocity in air which makes excitation and reception of such mode complicated. For excitation of both modes, we propose instead a single air-coupled ultrasonic transducer to use linear air-coupled arrays, which can be electronically readjusted to optimally excite and receive the A0 and S0 guided wave modes. The objective of this article was the numerical investigation of feasibility to excite different types of ultrasonic-guided waves, such as S0 and A0 modes in thin plastic films with the same electronically readjusted linear phased array. Three-dimensional and two-dimensional simulations of A0 and S0 Lamb wave modes using a single ultrasonic transducer and a linear phased array were performed. The obtained results clearly demonstrate feasibility to excite efficiently different guided wave modes in thin plastic films with readjusted phased array.

scholarly journals Air-Coupled Reception of a Slow Ultrasonic A0 Mode Wave Propagating in Thin Plastic Film

Sensors ◽  
2020 ◽  
Vol 20 (2) ◽  
pp. 516 ◽  
Author(s):  
Rymantas J. Kazys ◽  
Almantas Vilpisauskas
Keyword(s):  
Evanescent Wave ◽  
Ultrasound Velocity ◽  
Thin Plates ◽  
Destructive Testing ◽  
Low Frequencies ◽  
Plastic Films ◽  
Additional Signal ◽  
Virtual Array ◽  
Thin Plastic ◽  
Coupled Technique

At low frequencies, in thin plates the phase velocity of the guided A0 mode can become slower than that of the ultrasound velocity in air. Such waves do not excite leaky waves in the surrounding air, and therefore, it is impossible to excite and receive them by conventional air-coupled methods. The objective of this research was the development of an air-coupled technique for the reception of slow A0 mode in thin plastic films. This study demonstrates the feasibility of picking up a subsonic A0 mode in plastic films by air-coupled ultrasonic arrays. The air-coupled reception was based on an evanescent wave in air accompanying the propagating A0 mode in a film. The efficiency of the reception was enhanced by using a virtual array which was arranged from the data collected by a single air-coupled receiver. The signals measured at the points corresponding to the positions of the phase-matched array were recorded and processed. The transmitting array excited not only the A0 mode in the film, but also a direct wave in air. This wave propagated at ultrasound velocity in air and was faster than the evanescent wave. For efficient reception of the A0 mode, the additional signal-processing procedure based on the application of the 2D Fourier transform in a spatial–temporal domain. The obtained results can be useful for the development of novel air-coupled ultrasonic non-destructive testing techniques.

scholarly journals Air-Coupled Excitation of a Slow A0 Mode Wave in Thin Plastic Films by an Ultrasonic PMN-32%PT Array

Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 3156 ◽  
Author(s):  
Rymantas Kazys ◽  
Liudas Mazeika ◽  
Reimondas Sliteris ◽  
Justina Sestoke
Keyword(s):  
Lamb Wave ◽  
Composite Structures ◽  
Guided Waves ◽  
Ultrasound Velocity ◽  
Processing Technique ◽  
Wave Mode ◽  
Destructive Testing ◽  
Plastic Films ◽  
Directivity Patterns ◽  
Thin Plastic

Ultrasonic non-destructive testing techniques (NDT) based on the application of guided waves are already used for inspection of plate-type structures made of various materials, including composite materials. Air-coupled ultrasonic techniques are used to test such structures by means of guided waves. The objective of this research was development and investigation of air-coupled excitation of a slow A0 Lamb wave mode in thin plastic films by a PMN-32%PT ultrasonic array. It is known that when the velocity of the A0 mode in the film is less than the ultrasound velocity in air no leaky wave is observed in a surrounding air. It opens new possibilities for NDT of composite structures. The influence of the airborne wave may be eliminated by 3D filtering in a wavenumbers-frequency domain. A special filter and corresponding signals processing technique were developed in order to obtain directivity patterns and velocity maps of the waves propagating in all directions. The measured ultrasound velocity values prove that, with the proposed method, it is possible to excite a slow A0 Lamb wave mode and to separate it from other parasitic waves propagating in air. Measurements of the parameters of the slow A0 mode, such as the propagation velocity in the plastic film, may be applied for the material characterization.

Inspection of Concrete-Metal Rod Interface Using Guided Waves

2000 ◽  
Author(s):  
Won-Bae Na ◽  
Tribikram Kundu ◽  
Mohammad R. Ehsani
Keyword(s):  
Lamb Wave ◽  
Guided Waves ◽  
Lamb Waves ◽  
Guided Wave ◽  
Ultrasonic Transducers ◽  
Interface Debonding ◽  
Long Distance ◽  
Steel Rebar ◽  
Steel Bars ◽  
Steel Rebars

Abstract The feasibility of detecting interface degradation and separation of steel rebars in concrete beams using Lamb waves is investigated in this paper. It is shown that Lamb waves can easily detect these defects. A special coupler between the steel rebar and ultrasonic transducers has been used to launch non-axisymmetric guided waves in the steel rebar. This investigation shows that the Lamb wave inspection technique is an efficient and effective tool for health monitoring of reinforced concrete structures because the Lamb wave can propagate a long distance along the reinforcing steel bars embedded in concrete as the guided wave and is sensitive to the interface debonding between the steel rebar and concrete.

Early Fatigue Damage Evaluation of Nonlinear Guided Wave Imaging in Hyperelastic Materials

2021 ◽  
Author(s):  
Chengwei Zhao ◽  
Sunia Tanweer ◽  
Jian Li ◽  
Min Lin ◽  
Xiang Zhang ◽  
...  
Keyword(s):  
Fatigue Damage ◽  
Guided Waves ◽  
Lamb Waves ◽  
Tone Burst ◽  
Guided Wave ◽  
Third Order ◽  
Hyperelastic Materials ◽  
Third Order Elastic Constants ◽  
Wave Imaging ◽  
Processing Platform

Abstract Nonlinear ultrasonic guided waves have superior sensitivity of the early fatigue damage. This paper investigates the analysis of the second harmonics of Lamb waves in a free boundary aluminum plate, and the internal resonance conditions between the Lamb wave primary modes and the second harmonics. The Murnaghan’s model is implemented in a finite element (FE) analysis to describe the hyperelastic constitutive relation for nonlinear acoustic modeling. The second harmonics of s0 mode are actuated by a 60kHz Hanning-windowed tone burst. A guided wave signal processing platform is developed for tomographic imaging. The different stages of fatigue are reflected by the changes of third-order elastic constants (TOECs) in Murnaghan’s model. The reconstructed damage locations match well with the actual ones cross different degrees and depths of fatigue.

scholarly journals Warped Wigner-Hough Transform for Defect Reflection Enhancement in Ultrasonic Guided Wave Monitoring

2012 ◽  
Vol 2012 ◽  
pp. 1-15 ◽  
Author(s):  
Luca De Marchi ◽  
Emanuele Baravelli ◽  
Giampaolo Cera ◽  
Nicolò Speciale ◽  
Alessandro Marzani
Keyword(s):  
Hough Transform ◽  
Guided Waves ◽  
Lamb Waves ◽  
Guided Wave ◽  
Nonlinear Signal Processing ◽  
Localization Accuracy ◽  
Time Frequency ◽  
Ultrasonic Guided Wave ◽  
Inspection Systems ◽  
Nonlinear Signal

To improve the defect detectability of Lamb wave inspection systems, the application of nonlinear signal processing was investigated. The approach is based on a Warped Frequency Transform (WFT) to compensate the dispersive behavior of ultrasonic guided waves, followed by a Wigner-Ville time-frequency analysis and the Hough Transform to further improve localization accuracy. As a result, an automatic detection procedure to locate defect-induced reflections was demonstrated and successfully tested by analyzing numerically simulated Lamb waves propagating in an aluminum plate. The proposed method is suitable for defect detection and can be easily implemented for real-world structural health monitoring applications.

scholarly journals Nonlinear Guided Wave Tomography for Detection and Evaluation of Early-Life Material Degradation in Plates

Sensors ◽  
2021 ◽  
Vol 21 (16) ◽  
pp. 5498
Author(s):  
Chengwei Zhao ◽  
Sunia Tanweer ◽  
Jian Li ◽  
Min Lin ◽  
Xiang Zhang ◽  
...  
Keyword(s):  
Early Life ◽  
Guided Waves ◽  
Lamb Waves ◽  
Tone Burst ◽  
Guided Wave ◽  
Material Degradation ◽  
Third Order Elastic Constants ◽  
Metal Plates ◽  
Wave Tomography ◽  
Aluminum Plates

In this paper, the possibility of using nonlinear ultrasonic guided waves for early-life material degradation in metal plates is investigated through both computational modeling and study. The analysis of the second harmonics of Lamb waves in a free boundary aluminum plate, and the internal resonance conditions between the Lamb wave primary modes and the second harmonics are investigated. Subsequently, Murnaghan’s hyperelastic model is implemented in a finite element (FE) analysis to study the response of aluminum plates subjected to a 60 kHz Hanning-windowed tone burst. Different stages of material degradation are reflected as the changes in the third order elastic constants (TOECs) of the Murnaghan’s model. The reconstructed degradations match the actual ones well across various degrees of degradation. The effects of several relevant factors on the accuracy of reconstructions are also discussed.

scholarly journals Core–skin debonding detection in honeycomb sandwich structures through guided wave wavefield analysis

2018 ◽  
Vol 30 (9) ◽  
pp. 1306-1317 ◽  
Author(s):  
Lingyu Yu ◽  
Zhenhua Tian ◽  
Xiaopeng Li ◽  
Rui Zhu ◽  
Guoliang Huang
Keyword(s):  
Guided Waves ◽  
Sandwich Structures ◽  
Lamb Waves ◽  
Laser Doppler Vibrometer ◽  
Low Frequency ◽  
Guided Wave ◽  
Honeycomb Sandwich ◽  
Debonding Detection ◽  
The Waves ◽  
Detection And Quantification

Ultrasonic guided waves have proven to be an effective and efficient method for damage detection and quantification in various plate-like structures. In honeycomb sandwich structures, wave propagation and interaction with typical defects such as hidden debonding damage are complicated; hence, the detection of defects using guided waves remains a challenging problem. The work presented in this article investigates the interaction of low-frequency guided waves with core–skin debonding damage in aluminum core honeycomb sandwich structures using finite element simulations. Due to debonding damage, the waves propagating in the debonded skin panel change to fundamental antisymmetric Lamb waves with different wavenumber values. Exploiting this mechanism, experimental inspection using a non-contact laser Doppler vibrometer was performed to acquire wavefield data from pristine and debonded structures. The data were then processed and analyzed with two wavefield data–based imaging approaches, the filter reconstruction imaging and the spatial wavenumber imaging. Both approaches can clearly indicate the presence, location, and size of the debonding in the structures, thus proving to be effective methods for debonding detection and quantification for honeycomb sandwich structures.

scholarly journals Application of Air-Coupled Ultrasonic Arrays for Excitation of a Slow Antisymmetric Lamb Wave

Sensors ◽  
2018 ◽  
Vol 18 (8) ◽  
pp. 2636 ◽  
Author(s):  
Rymantas Kazys ◽  
Almantas Vilpisauskas ◽  
Justina Sestoke
Keyword(s):  
Lamb Wave ◽  
Guided Waves ◽  
Ultrasound Velocity ◽  
Optimization Procedure ◽  
Wave Mode ◽  
Zero Order ◽  
Air Gap ◽  
Thin Plates ◽  
Low Frequencies ◽  
Excitation Method

Air-coupled excitation and reception of ultrasonic guided waves is already used for non-destructive testing and evaluation (NDT & E). Usually for air-coupled NDT & E purposes the lowest zero-order antisymmetric Lamb wave mode A0 is used, because it is most sensitive to internal defects and thickness variations. The velocity of the A0 mode is reduced with a reducing frequency and at low frequencies may become slower than the ultrasound velocity in air. Such a wave is named a slow Lamb wave. The objective of this research was the development and investigation of an air-coupled excitation method of the slow zero-order antisymmetric Lamb wave based on application of a piezoceramic ultrasonic array. We have proposed to excite the A0 mode by a planar air-coupled phased array with rectangular elements. The array is matched to the wavelength of the A0 mode in the film. Performance of such an excitation method was investigated both theoretically and experimentally. Two excitation methods of the array were analysed: when all array elements were excited simultaneously or one by one with a proper delay. In order to reduce crosstalk between array elements via the air gap, we have proposed an optimization procedure based on additional shifts of electric excitation impulses of the array elements. For experimental verification of the proposed approach a prototype of the air-coupled eight element array made of Pz-29 piezoceramic strips was manufactured. Experimental validation confirmed the possibility of exciting the slow A0 Lamb wave mode through the air gap in thin plates and films.

NUMERICAL MODELING OF WALL THINNING DEFECTS CHARACTERIZATION: APPLICATIONS IN LAMB WAVE GENERATION AND INTERACTION

2008 ◽  
Vol 22 (11) ◽  
pp. 935-940
Author(s):  
HYUNJO JEONG ◽  
SEUNG-SEOK LEE ◽  
YOUNG-GIL KIM
Keyword(s):  
Guided Waves ◽  
Lamb Waves ◽  
Mode Conversion ◽  
Wave Interaction ◽  
Guided Wave ◽  
Destructive Interference ◽  
Wall Thinning ◽  
Mode Dispersion ◽  
Periodic Ring ◽  
Axisymmetric Scattering

The generation of axisymmetric Lamb waves and interaction with wall thinning (corrosion) defects in hollow cylinders are simulated using the finite element method. Guided wave interaction with defects in cylinders is challenged by the multi-mode dispersion and the mode conversion. In this paper, two longitudinal, axisymmetric modes are generated using the concept of a time-delay periodic ring arrays (TDPRA), which makes use of the constructive/destructive interference concept to achieve the unidirectional emission and reception of guided waves. The axisymmetric scattering by the wall thinning extending in full circumference of a cylinder is studied with a two-dimensional FE simulation. The effect of wall thinning depth, axial extension, and the edge shape on the reflections of guided waves is discussed.

Sign in / Sign up

Export Citation Format

Share Document