scholarly journals Characterization of cavitation-radiated acoustic power using diffraction correction

2018 ◽  
Vol 144 (6) ◽  
pp. 3563-3574 ◽  
Author(s):  
Kyle T. Rich ◽  
Christy K. Holland ◽  
Marepalli B. Rao ◽  
T. Douglas Mast
Keyword(s):  
Acoustic Power ◽  
Diffraction Correction

A Whistling Criterion for Two Orifices in Series

2009 ◽  
Author(s):  
Romain Lacombe ◽  
Yves Aure´gan ◽  
Pierre Moussou
Keyword(s):  
Pressure Drop ◽  
Power Plants ◽  
Acoustic Power ◽  
Scattering Matrix ◽  
In Series ◽  
Inner Diameter ◽  
Acoustic Amplifier ◽  
Experimental Criterion

Whistling phenomena in pipe power plants have been observed in the past years. It occurs at pressure drop devices where vortex shedding is established. It generates high noise levels and excessive vibrations. Aure´gan and Starobinsky [1] have developed an experimental criterion to predict whistling frequencies of pressure drop devices submitted to plane propagating pressure waves. This criterion estimates the net acoustic power, an acoustic exergy generation indicating that the device behaves as an acoustic amplifier. The corresponding frequencies are potential whistling frequencies. The application of the criterion only requires the determination of the scattering matrix of the device. In previous works, this criterion was applied to different single hole orifices. The purpose of the present study is to apply the criterion to two orifices in series and to verify that the behavior of this system can be predicted from the scattering matrix of each individual orifice and of the straight pipe in-between. Measurements are done on an air test rig with an inner diameter of 3 cm, a Mach number of 2.6 × 10−2 and a Reynolds number of 104. Different distances between orifices are characterized. The study of the influence of the second orifice on the whistling criterion shows an enhancement of the whistling potential and a shift of the main potential whistling frequency. A fair agreement is found between experimental and predicted results. Characterization of orifices in series is then possible from the coefficients of the scattering matrix of one orifice and an appropriate condition on the distance between the orifices.

US Characterization of Focal Hepatic Lesions with Intermittent High-Acoustic-Power Mode and Contrast Material

2003 ◽  
Vol 10 (7) ◽  
pp. 739-750 ◽  
Author(s):  
Emilio Quaia ◽  
Michele Bertolotto ◽  
Loretta Calderan ◽  
Elisa Mosconi ◽  
Roberto Pozzi Mucelli
Keyword(s):  
Contrast Material ◽  
Acoustic Power ◽  
Focal Hepatic Lesions ◽  
Power Mode ◽  
Hepatic Lesions

Morphological Characterization of Mycobacteriophage R1

1974 ◽  
Vol 32 ◽  
pp. 254-255
Author(s):  
B. L. Soloff ◽  
T. A. Rado
Keyword(s):  
Carbon Source ◽  
Stationary Phase ◽  
Growth Phase ◽  
Minimal Medium ◽  
Morphological Characterization ◽  
Logarithmic Growth Phase ◽  
Complete Lysis ◽  
Lysogenic Culture ◽  
Logarithmic Growth

Mycobacteriophage R1 was originally isolated from a lysogenic culture of M. butyricum. The virus was propagated on a leucine-requiring derivative of M. smegmatis, 607 leu−, isolated by nitrosoguanidine mutagenesis of typestrain ATCC 607. Growth was accomplished in a minimal medium containing glycerol and glucose as carbon source and enriched by the addition of 80 μg/ ml L-leucine. Bacteria in early logarithmic growth phase were infected with virus at a multiplicity of 5, and incubated with aeration for 8 hours. The partially lysed suspension was diluted 1:10 in growth medium and incubated for a further 8 hours. This permitted stationary phase cells to re-enter logarithmic growth and resulted in complete lysis of the culture.

AEM analysis of crystallization in Ti-based amorphous alloys

1983 ◽  
Vol 41 ◽  
pp. 270-271
Author(s):  
A.R. Pelton ◽  
A.F. Marshall ◽  
Y.S. Lee
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Amorphous Materials ◽  
Isothermal Annealing ◽  
Amorphous Matrix ◽  
Nucleation And Growth ◽  
Current Interest ◽  
Amorphous Films ◽  
Electrical And Magnetic Properties

Amorphous materials are of current interest due to their desirable mechanical, electrical and magnetic properties. Furthermore, crystallizing amorphous alloys provides an avenue for discerning sequential and competitive phases thus allowing access to otherwise inaccessible crystalline structures. Previous studies have shown the benefits of using AEM to determine crystal structures and compositions of partially crystallized alloys. The present paper will discuss the AEM characterization of crystallized Cu-Ti and Ni-Ti amorphous films.Cu60Ti40: The amorphous alloy Cu60Ti40, when continuously heated, forms a simple intermediate, macrocrystalline phase which then transforms to the ordered, equilibrium Cu3Ti2 phase. However, contrary to what one would expect from kinetic considerations, isothermal annealing below the isochronal crystallization temperature results in direct nucleation and growth of Cu3Ti2 from the amorphous matrix.

Characterization of Coherent, Ordered Precipitates in Nickel-Base Alloys

1973 ◽  
Vol 31 ◽  
pp. 144-145
Author(s):  
B. H. Kear ◽  
J. M. Oblak
Keyword(s):  
Stable Phase ◽  
Nickel Base Superalloy ◽  
Alloy 718 ◽  
Commercial Alloy ◽  
Precipitate Morphology ◽  
Continuous Precipitation ◽  
Nickel Base ◽  
Base Superalloy ◽  
Strengthening Precipitate

A nickel-base superalloy is essentially a Ni/Cr solid solution hardened by additions of Al (Ti, Nb, etc.) to precipitate a coherent, ordered phase. In most commercial alloy systems, e.g. B-1900, IN-100 and Mar-M200, the stable precipitate is Ni3 (Al,Ti) γ′, with an LI2structure. In A lloy 901 the normal precipitate is metastable Nis Ti3 γ′ ; the stable phase is a hexagonal Do2 4 structure. In Alloy 718 the strengthening precipitate is metastable γ″, which has a body-centered tetragonal D022 structure.Precipitate MorphologyIn most systems the ordered γ′ phase forms by a continuous precipitation re-action, which gives rise to a uniform intragranular dispersion of precipitate particles. For zero γ/γ′ misfit, the γ′ precipitates assume a spheroidal.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Skeletal elements of crinoid echinoderms: High-resolution structural and microanalytical results

1983 ◽  
Vol 41 ◽  
pp. 194-195
Author(s):  
D. F. Blake ◽  
L. F. Allard ◽  
D. R. Peacor
Keyword(s):  
High Resolution ◽  
Marine Invertebrates ◽  
Sea Urchins ◽  
Structural Features ◽  
Sea Stars ◽  
High Resolution Tem ◽  
Relationship Of ◽  
The Relationship ◽  
Insight Into

Echinodermata is a phylum of marine invertebrates which has been extant since Cambrian time (c.a. 500 m.y. before the present). Modern examples of echinoderms include sea urchins, sea stars, and sea lilies (crinoids). The endoskeletons of echinoderms are composed of plates or ossicles (Fig. 1) which are with few exceptions, porous, single crystals of high-magnesian calcite. Despite their single crystal nature, fracture surfaces do not exhibit the near-perfect {10.4} cleavage characteristic of inorganic calcite. This paradoxical mix of biogenic and inorganic features has prompted much recent work on echinoderm skeletal crystallography. Furthermore, fossil echinoderm hard parts comprise a volumetrically significant portion of some marine limestones sequences. The ultrastructural and microchemical characterization of modern skeletal material should lend insight into: 1). The nature of the biogenic processes involved, for example, the relationship of Mg heterogeneity to morphological and structural features in modern echinoderm material, and 2). The nature of the diagenetic changes undergone by their ancient, fossilized counterparts. In this study, high resolution TEM (HRTEM), high voltage TEM (HVTEM), and STEM microanalysis are used to characterize tha ultrastructural and microchemical composition of skeletal elements of the modern crinoid Neocrinus blakei.

Some applications of electron beam microanalysis techniques in VLSI process evaluation

1983 ◽  
Vol 41 ◽  
pp. 160-161
Author(s):  
Simon Thomas
Keyword(s):  
Integrated Circuits ◽  
Process Evaluation ◽  
Large Scale ◽  
Technology Development ◽  
Analytical Techniques ◽  
Successful Implementation ◽  
Analysis Of Failures ◽  
Characterization Of Materials ◽  
Circuits Vlsi

Trends in the technology development of very large scale integrated circuits (VLSI) have been in the direction of higher density of components with smaller dimensions. The scaling down of device dimensions has been not only laterally but also in depth. Such efforts in miniaturization bring with them new developments in materials and processing. Successful implementation of these efforts is, to a large extent, dependent on the proper understanding of the material properties, process technologies and reliability issues, through adequate analytical studies. The analytical instrumentation technology has, fortunately, kept pace with the basic requirements of devices with lateral dimensions in the micron/ submicron range and depths of the order of nonometers. Often, newer analytical techniques have emerged or the more conventional techniques have been adapted to meet the more stringent requirements. As such, a variety of analytical techniques are available today to aid an analyst in the efforts of VLSI process evaluation. Generally such analytical efforts are divided into the characterization of materials, evaluation of processing steps and the analysis of failures.

Sign in / Sign up

Export Citation Format

Share Document