Back side emission microscopy for failure analysis

1996 ◽  
Author(s):  
Nevil M. Wu ◽  
Kenneth Tang ◽  
James H. Lin
Keyword(s):  
Failure Analysis ◽  
Back Side ◽  
Emission Microscopy ◽  
Side Emission

Failure Analysis From Back Side of Die

1996 ◽  
Author(s):  
N.M. Wu ◽  
K. Weaver ◽  
J.H. Lin
Keyword(s):  
Failure Analysis ◽  
Fault Isolation ◽  
Back Side ◽  
Induced Current ◽  
Front Side ◽  
Root Cause ◽  
Isolation Techniques ◽  
Cause Of Failure ◽  
Emission Microscopy ◽  
Side Emission

Abstract With increasing complexity of circuit layout on the die and special packages in which the die are flipped over, failure analysis on the die front side, sometimes, can not solve the problems or is not possible by opening the front side of the package to expose the die front side. This paper discusses fault isolation techniques and procedures used on the back side of the die. The two major back side techniques, back side emission microscopy and back side OBIC (Optical Beam Induced Current), are introduced and applied to solve real problems in failure analysis. A back side decapsulation technique and procedure are also introduced. Last, several examples are given. The results indicated that the success in finding root cause of failure is greatly increased when these techniques are used in addition to the traditional front side analysis approaches.

Scanning Optical Microscopy Application in Micron® Memory Devices

2005 ◽  
Author(s):  
Wong Yaw Yuan ◽  
T.L. Edmund Poh ◽  
David Lam
Keyword(s):  
Failure Analysis ◽  
Integrated Circuit ◽  
Semiconductor Industry ◽  
Fault Isolation ◽  
Memory Devices ◽  
Back Side ◽  
Induced Voltage ◽  
Scanning Optical Microscopy ◽  
Side Emission ◽  
Complex Circuits

Abstract The migration to smaller geometries has translated to an increase in the number of transistors possible in each integrated circuit. Failure analysis of such complex circuits presents a major challenge to the semiconductor industry and is a driving force behind the considerable interest in nondestructive, cost-efficient, “shortcut” fault isolation techniques. In this paper, we present the application of thermal-induced voltage alteration (TIVA) for failure analysis of 0.11µm technology memory devices and demonstrate the key aspects of this technique. The back side TIVA results are compared with analysis performed using back side emission microscopy (EMMI), and the limitations of EMMI are highlighted. The advantages and limitations of the TIVA technique are also discussed.

Analysis of Delta Iddq Soft Fails on Pass Chips

2006 ◽  
Author(s):  
I. Österreicher ◽  
S. Eckl ◽  
B. Tippelt ◽  
S. Döring ◽  
R. Prang ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Failure Mode ◽  
Photon Emission ◽  
Complete Analysis ◽  
Functional Tests ◽  
Analysis Techniques ◽  
Atomic Force ◽  
Current Consumption ◽  
Emission Microscopy ◽  
Failure Localization

Abstract Depending on the field of application the ICs have to meet requirements that differ strongly from product to product, although they may be manufactured with similar technologies. In this paper a study of a failure mode is presented that occurs on chips which have passed all functional tests. Small differences in current consumption depending on the state of an applied pattern (delta Iddq measurement) are analyzed, although these differences are clearly within the usual specs. The challenge to apply the existing failure analysis techniques to these new fail modes is explained. The complete analysis flow from electrical test and Global Failure Localization to visualization is shown. The failure is localized by means of photon emission microscopy, further analyzed by Atomic Force Probing, and then visualized by SEM and TEM imaging.

Failure Analysis of Killer Defects and Yield Enhancement of Flat ROM Devices in Wafer Fabrication

2000 ◽  
Author(s):  
Y. N. Hua ◽  
Z. R. Guo ◽  
L. H. An ◽  
Shailesh Redkar
Keyword(s):  
Electron Microscope ◽  
Failure Analysis ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Wafer Fabrication ◽  
X Ray ◽  
Particle Contamination ◽  
Emission Microscopy ◽  
Microscopy Techniques ◽  
Scanning Electron

Abstract In this paper, some low yield cases in Flat ROM device (0.45 and 0.6 µm) were investigated. To find killer defects and particle contamination, KLA, bitmap and emission microscopy techniques were used in fault isolation. Reactive ion etching (RIE) and chemical delayering, 155 Wright Etch, BN+ Etch and scanning electron microscope (SEM) were used for identification and inspection of defects. In addition, energy-dispersive X-ray microanalysis (EDX) was used to determine the composition of the particle or contamination. During failure analysis, seven kinds of killer defects and three killer particles were found in Flat ROM devices. The possible root causes, mechanisms and elimination solutions of these killer defects/particles were also discussed.

SRAM Failure Analysis Strategy

2003 ◽  
Author(s):  
P. Egger ◽  
C. Burmer
Keyword(s):  
Liquid Crystal ◽  
Failure Analysis ◽  
The Other ◽  
Other Hand ◽  
Analysis Strategy ◽  
Emission Microscopy ◽  
Metal Layers ◽  
Failure Localization

Abstract The area of embedded SRAMs in advanced logic ICs is increasing more and more. On the other hand smaller structure sizes and an increasing number of metal layers make conventional failure localization by using emission microscopy or liquid crystal inefficient. In this paper a SRAM failure analysis strategy will be presented independent on layout and technology.

Pseudo-Dynamic Fault Isolation Technique Using Backside Emission Microscopy – Case Study, Where All Other Methods Fail

2002 ◽  
Author(s):  
Yoav Weizman ◽  
Ezra Baruch ◽  
Michael Zimin
Keyword(s):  
Failure Analysis ◽  
Process Variations ◽  
Fault Isolation ◽  
Operating Conditions ◽  
Detection Sensitivity ◽  
Isolation Technique ◽  
Root Cause ◽  
Emission Microscopy ◽  
Failure Location ◽  
Noisy Background

Abstract Emission microscopy is usually implemented for static operating conditions of the DUT. Under dynamic operation it is nearly impossible to identify a failure out of the noisy background. In this paper we describe a simple technique that could be used in cases where the temporal location of the failure was identified however the physical location is not known or partially known. The technique was originally introduced to investigate IDDq failures (1) in order to investigate timing related issues with automated tester equipment. Ishii et al (2) improved the technique and coupled an emission microscope to the tester for functional failure analysis of DRAMs and logic LSIs. Using consecutive step-by-step tester halting coupled to a sensitive emission microscope, one is able detect the failure while it occurs. We will describe a failure analysis case in which marginal design and process variations combined to create contention at certain logic states. Since the failure occurred arbitrarily, the use of the traditional LVP, that requires a stable failure, misled the analysts. Furthermore, even if we used advanced tools as PICA, which was actually designed to locate such failures, we believe that there would have been little chance of observing the failure since the failure appeared only below 1.3V where the PICA tool has diminished photon detection sensitivity. For this case the step-by-step halting technique helped to isolate the failure location after a short round of measurements. With the use of logic simulations, the root cause of the failure was clear once the failing gate was known.

Yield and Failure Analysis of FinFET Source to Drain Leakage in 12nm Technology

2020 ◽  
Author(s):  
Felix Beaudoin ◽  
Satish Kodali ◽  
Rohan Deshpande ◽  
Wayne Zhao ◽  
Edmund Banghart ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Fault Localization ◽  
Detailed Characterization ◽  
Laser Stimulation ◽  
Emission Microscopy ◽  
Scan Chain ◽  
Multiple Samples ◽  
Tem Lamella ◽  
Diffusion Activation

Abstract Fault localization using both dynamic laser stimulation and emission microscopy was used to localize the failing transistors within the failing scan chain latch on multiple samples. Nanoprobing was then performed and the source to drain leakage in N-type FinFETs was identified. After extensive detailed characterization, it was concluded that the N-type dopant signal was likely due to projections from the source/drain regions included in the TEM lamella. Datamining identified the scan chain fail to be occurring uniquely for a specific family of tools used during source/drain implant diffusion activation. This paper discusses the processes involved in yield delta datamining of FinFET and its advantages over failure characterization, fault localization, nanoprobing, and physical failure analysis.

Sign in / Sign up

Export Citation Format

Share Document