Double-patterning interactions with wafer processing, optical proximity correction, and physical design flows

Abstract Many semiconductor products are manufactured with mature technologies involving the uses of aluminum (Al) lines and tungsten (W) vias. High resistances of the vias were sometimes observed only after electrical or thermal stress. A layer of Ti oxide was found on such a via. In the wafer processing, the post W chemical mechanical planarization (WCMP) cleaning left residual W oxide on the W plugs. Ti from the overlaying metal line spontaneously reduced the W oxide, through which Ti oxide formed. Compared with W oxide, the Ti oxide has a larger formation enthalpy, and the valence electrons of Ti are more tightly bound to the O ion cores. As a result, the Ti oxide is more resistive than the W oxide. Consequently, the die functioned well in the first test in the fab, but the via resistance increased significantly after a thermal stress, which led to device failure in the second test. The NH4OH concentration was therefore increased to more effectively remove residual W oxide, which solved the problem. The thermal stress had prevented the latent issue from becoming a more costly field failure.

Download Full-text

Impact of Metal Pad Etch-Induced Plasma Damage on Dynamic Retention Time Degradation during High Temperature Stress in High Density DRAM Technology

ISTFA 2005: Conference Proceedings from the 31st International Symposium for Testing and Failure Analysis ◽

10.31399/asm.cp.istfa2005p0407 ◽

2005 ◽

Author(s):

D-J Kim ◽

I-G Kim ◽

J-Y Noh ◽

H-J Lee ◽

S-H Park ◽

...

Keyword(s):

High Temperature ◽

Temperature Stress ◽

Retention Time ◽

High Temperature Stress ◽

High Density ◽

Cell Junction ◽

Antenna Effect ◽

Plasma Damage ◽

Root Cause ◽

Wafer Processing

Abstract As DRAM technology extends into 12-inch diameter wafer processing, plasma-induced wafer charging is a serious problem in DRAM volume manufacture. There are currently no comprehensive reports on the potential impact of plasma damage on high density DRAM reliability. In this paper, the possible effects of floating potential at the source/drain junction of cell transistor during high-field charge injection are reported, and regarded as high-priority issues to further understand charging damage during the metal pad etching. The degradation of block edge dynamic retention time during high temperature stress, not consistent with typical reliability degradation model, is analyzed. Additionally, in order to meet the satisfactory reliability level in volume manufacture of high density DRAM technology, the paper provides the guidelines with respect to plasma damage. Unlike conventional model as gate antenna effect, the cell junction damage by the exposure of dummy BL pad to plasma, was revealed as root cause.

Download Full-text

Localization Techniques on a 0.15um CMOS Device: Charge Pump Failure Analysis

ISTFA 2002: Conference Proceedings from the 28th International Symposium for Testing and Failure Analysis ◽

10.31399/asm.cp.istfa2002p0771 ◽

2002 ◽

Author(s):

Hui Pan ◽

Thomas Gibson

Keyword(s):

Failure Analysis ◽

Focused Ion Beam ◽

Ion Beam ◽

Electrical Characterization ◽

Charge Pump ◽

Front Side ◽

Pump Failure ◽

Electrical Failure ◽

Optical Proximity Correction ◽

A Charge

Abstract In recent years, there have been many advances in the equipment and techniques used to isolate faults. There are many options available to the failure analyst. The available techniques fall into the categories of electrical, photonic, thermal and electron/ion beam [1]. Each technique has its advantages and its limitations. In this paper, we introduce a case of successful failure analysis using a combination of several fault localization techniques on a 0.15um CMOS device with seven layers of metal. It includes electrical failure mode characterization, front side photoemission, backside photoemission, Focused Ion Beam (FIB), Scanning Electron Microscope (SEM) and liquid crystal. Electrical characterization along with backside photoemission proved most useful in this case as a poly short problem was found to be causing a charge pump failure. A specific type of layout, often referred to as a hammerhead layout, and the use of Optical Proximity Correction (OPC) contributed to the poly level shorts.

Download Full-text

Physical Design, Preparation and Functionalization of Carbon Membranes for Gas Separation

Journal of Inorganic Materials ◽

10.3724/sp.j.1077.2010.00449 ◽

2010 ◽

Vol 25 (5) ◽

pp. 449-456 ◽

Cited By ~ 2

Author(s):

Lin LI ◽

Tong-Hua WANG ◽

Yi-Ming CAO ◽

Jie-Shan QIU

Keyword(s):

Gas Separation ◽

Physical Design ◽

Carbon Membranes

Download Full-text