Scaled Experiments and CFD Simulations Supporting the Design of the Spallation Neutron Source Mercury Target

2000 ◽  
Author(s):  
W. David Pointer ◽  
Mark W. Wendel ◽  
Jason M. Crye ◽  
Arthur E. Ruggles ◽  
David K. Felde ◽  
...  
Keyword(s):  
Neutron Source ◽  
Cfd Simulation ◽  
Complete Characterization ◽  
Experimental Program ◽  
Working Fluid ◽  
Spallation Neutron Source ◽  
Cfd Simulations ◽  
Liquid Mercury ◽  
Computational Fluid Dynamics Cfd

Abstract A combination of experimental and computational methods is necessary to adequately characterize the flow patterns in the liquid mercury target of the Spallation Neutron Source (SNS). Since liquid mercury is completely opaque and corrosive to many materials, the use of liquid mercury as the working fluid makes complete characterization of the flow field by experiment difficult. Furthermore, flow asymmetries and quasi-periodic instabilities that are observed in early target flow experiments are difficult to capture in computational fluid dynamics (CFD) simulations of the system. Therefore, an experimental program using several scaled experiments is combined with CFD simulation for the design and development of the SNS mercury target.

scholarly journals Transient 3D CFD Simulation of a Stationary Vane, Oil Free, Rotary Compressor

2019 ◽  
Vol 63 (4) ◽  
pp. 308-318 ◽  
Author(s):  
Balázs Farkas ◽  
Jenő Miklós Suda
Keyword(s):  
Cfd Simulation ◽  
Piston Compressor ◽  
Working Fluid ◽  
Rotary Compressor ◽  
Heat Sources ◽  
Cfd Model ◽  
Cfd Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Rolling Piston ◽  
Good Agreement

The evaluation of a newly designed oil-free rotary compressor is presented based on transient 3D Computational Fluid Dynamics (CFD) simulations. The simulations are performed at low compression ratios and low pressure ratios and low rotational speeds. To place the results into context, the data presented in related literature was processed and summarized. The methods related to the CFD model of the newly designed compressor were developed, summarized and evaluated. The accessed CFD data are in good agreement with the results of the former rolling piston compressor related investigations. The oil free operation prevents the contamination of the working fluid from lubricant. Since the compressor is planned to work in open cycle within the sensitive environment of thermal heat sources contamination free operation has to be accomplished. However, oil-free operation also results in significantly lower performance based on the modelling results.

scholarly journals Investigations of Inducers Operating With High Rotational Speed

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Björn Gwiasda ◽  
Matthias Mohr ◽  
Martin Böhle
Keyword(s):  
Rotational Speed ◽  
Test Bench ◽  
Pressure Rise ◽  
Working Fluid ◽  
Cfd Simulations ◽  
High Rotational Speed ◽  
Rotating Speed ◽  
Performance Pressure ◽  
Computational Fluid Dynamics Cfd ◽  
Suction Performance

Suction performance, pressure rise, and efficiency for four different inducers are examined with computational fluid dynamics (CFD) simulations and experiments performed with 18,000 rpm and 24,000 rpm. The studies originate from a research project that includes the construction of a new test bench in order to judge the design of the different inducers. This test bench allows to conduct experiments with a rotational speed of up to 40,000 rpm and high pressure ranges from 0.1 bar to 40 bar with water as working fluid. Experimental results are used to evaluate the accuracy of the simulations and to gain a better understanding of the design parameter. The influence of increasing the rotating speed from 18,000 rpm to 24,000 rpm on the performance is also shown.

CFD simulation of empty fuel tanks separation from a trainer jet

2020 ◽  
Vol 92 (10) ◽  
pp. 1459-1468
Author(s):  
Aleksander Olejnik ◽  
Adam Dziubiński ◽  
Łukasz Kiszkowiak
Keyword(s):  
Cfd Simulation ◽  
Body Movement ◽  
Cfd Simulations ◽  
Content Type ◽  
Sequential Release ◽  
Wind Tunnel Data ◽  
Computational Fluid Dynamics Cfd ◽  
External Forces ◽  
Additional Value ◽  
Control Surfaces

Purpose This study aims to create 6-degree of freedom (SDOF) for computational fluid dynamics (CFD) simulations of body movement, and to validate using the experimental data for empty tank separation from I-22 Iryda jet trainer. The procedure has an ability to be modified or extended, to simulate, for example, a sequential release from the joints. Design/methodology/approach A set of CFD simulations are calculated. Both the SDOF procedure and the CFD simulation settings are validated using the wind tunnel data available for the aircraft. Findings The simulation using designed procedure gives predictable results, but offers availability to be modified to represent external forces, i.e. from body interaction or control system without necessity to model the control surfaces. Practical implications The procedure could be used to model the separation of external stores and design the deployment of anti-radar chaff, flares or ejection seats. Originality/value The work presents original work, caused by insufficient abilities of original SDOF procedure in ANSYS code. Additional value is the ability of the procedure to be easily modified.

scholarly journals Thermal management of machine compartment in a built-in refrigerator

2018 ◽  
Vol 240 ◽  
pp. 05005
Author(s):  
Milind Devle ◽  
Ankur Garg ◽  
Darci Cavali
Keyword(s):  
Heat Exchange ◽  
Cfd Simulation ◽  
Heat Extraction ◽  
Free Standing ◽  
Cfd Simulations ◽  
Performance Effectiveness ◽  
Hot Air ◽  
Computational Fluid Dynamics Cfd ◽  
Major Factors ◽  
Side Gap

In general a multi-door refrigerator machine compartment comprises of fan, condenser, compressor, control box, drain tray, and drain tubes. The performance of machine compartment depends upon the efficiency of heat extraction or heat exchange from heat generating components such as condenser and compressor. The efficiency of heat exchange can be improved by addressing two major factors, namely (1) Air bypass and (2) Hot air recirculation. The hot air recirculation in the machine compartment for builtin multi-door refrigerator configuration is the focus of this study. The results from Computational Fluid Dynamics (CFD) simulations show that efficiency of heat exchange for built-in application is lower than that for free-standing configuration. Recirculation of hot air and reduction in airflow are the two major factors which contribute towards the variation in machine compartment performance. The CFD simulations were coupled with Partial Factorial Design of Experiment (DoE) approach to systematically investigate the effect of variables such as (a) side gap and top gap between kitchen cabinetry and the refrigerator, (b) the baffle/flap (i.e. back and bottom of machine compartment) on the performance effectiveness of machine compartment. The results of the simulation provided critical design improvement directions resulting in performance improvement. Furthermore, the CFD simulation results were also compared to test data and the results compared favourably.

CFD Simulations of the Cold Neutron Source at the OPAL Reactor

2020 ◽  
Author(s):  
James L Spedding ◽  
Mark Ho ◽  
Weijian Lu
Keyword(s):  
Neutron Source ◽  
Cold Neutron ◽  
Operating Conditions ◽  
Convergence Time ◽  
Cfd Model ◽  
Cfd Simulations ◽  
Cold Neutron Source ◽  
Order Of Magnitude ◽  
Computational Fluid Dynamics Cfd ◽  
Polyhedral Mesh

Abstract The Open Pool Australian Light-water (OPAL) reactor Cold Neutron Source (CNS) is a 20 L liquid deuterium thermosiphon system which has performed consistently but will require replacement in the future. The CNS deuterium exploits neutronic heating to passively drive the thermosiphon loop and is cryogenically cooled by forced convective helium flow via a heat exchanger. In this study, a detailed computational fluid dynamics (CFD) model of the complete thermosiphon system was developed for simulation. Unlike previous studies, the simulation employed a novel polyhedral mesh technique. Results demonstrated that the polyhedral technique reduced simulation computational requirements and convergence time by an order of magnitude while predicting thermosiphon performance to within 1% accuracy when compared with prototype experiments. The simulation model was extrapolated to OPAL operating conditions and confirmed the versatility of the CFD model as an engineering design and preventative maintenance tool. Finally, simulations were performed on a proposed second-generation CNS design that increases the CNS moderator deuterium volume by 5 L, and results confirmed that the geometry maintains the thermosiphon deuterium in the liquid state and satisfies the CNS design criteria.

Transient CFD Visualization of Fossil Fuel Combustion Simulations

2003 ◽  
Author(s):  
Brian Dotson ◽  
Kent Eshenberg ◽  
Chris Guenther ◽  
Thomas O’Brien
Keyword(s):  
Power Plants ◽  
High Efficiency ◽  
Cfd Simulation ◽  
Low Cost ◽  
Three Dimensional ◽  
Cfd Simulations ◽  
Projection System ◽  
Computational Fluid Dynamics Cfd ◽  
High Level ◽  
Wall System

The design of high-efficiency lower-emission coal-fed power plants is facilitated by the extensive use of computational fluid dynamics (CFD) simulations. This paper describes work conducted at the National Energy Technology Laboratory (NETL) and Pittsburgh Supercomputing Center (PSC) to provide an environment for the immersive three-dimensional visualization of CFD simulation results. A low-cost high-resolution projection system has been developed in the visualization lab at NETL. This multi-wall system consists of four projection screens, three of which are tiled into four quadrants. The graphics for the multi-wall system are rendered using a cluster of eight personal computers. A high-level visualization interface named Mavis has also been developed to combine the powerful 3D modules of OpenDX with methods developed at NETL for studying multiphase CFD data. With Python, a completely new OpenDX user interface was built that extends and simplifies the features of a basic graphics library.

Improving Computational Fluid Dynamics Simulations for the Spallation Neutron Source Jet-Flow Target

2016 ◽  
Author(s):  
C. Barbier ◽  
E. Dominguez-Ontiveros
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Neutron Source ◽  
Jet Flow ◽  
Computational Time ◽  
Spallation Neutron Source ◽  
Mean Flow ◽  
Cfd Simulations ◽  
Flow Measurements ◽  
Piv Measurements

A liquid mercury target is used at Oak Ridge National Laboratory’s (ORNL [1]) Spallation Neutron Source (SNS [2]) to generate neutrons. The mercury is flowing in a stainless steel containment vessel for neutron spallation, but also to cool the vessel itself. Computational Fluid Dynamics (CFD) simulations have been used to estimate the temperature and pressure fields needed for the thermal stress analysis. Because of the geometry complexity, the high turbulence number, and the computational time requirements, generating a quality mesh that can accurately capture the flow and heat transfer has always been a challenge. However, with today’s High Performance Computing (HPC) advances, larger and larger meshes can now be used and better accuracy can be achieved. In this study, two meshing methods were used for the SNS jet-flow target: automatic tetrahedral method (ANSYS meshing) and manual hexahedral meshing (ICEM-CFD). Both methods are compared in terms of quality, size, ease of generation, convergence, and user-friendliness. Both meshes were used with ANSYS-CFX to simulate the steady, Newtonian, single phase, isothermal, incompressible and turbulent flow in the target. The Shear Stress Transport (SST) k-ω model developed by Menter [3] was used for turbulence modeling. The accuracy of the CFD simulations are tested against experimental data presented in the current paper. An in-depth series of Particle Image Velocimetry (PIV) measurements performed on a “visual jet-flow target”, an acrylic replica target running with water, are presented in the paper. Since flow measurements in mercury are difficult, a water loop was built to investigate the flow in the target and a potential gas injection in the flow to mitigate the pressure wave [4]. A PIV system on a precise translation stage was setup on the water loop to perform detailed and accurate PIV measurements. Mean flow velocity fields were used to validate the CFD simulations. The paper concludes on the choice for mesh generation for future target analysis, and the path forward for CFD simulations for the future SNS targets.

Characterization of irradiated AISI 316L stainless steel disks removed from the Spallation Neutron Source

2014 ◽  
Vol 450 (1-3) ◽  
pp. 147-162 ◽  
Author(s):  
Bradley J. Vevera ◽  
David A. McClintock ◽  
James W. Hyres ◽  
Bernard W. Riemer
Keyword(s):  
Stainless Steel ◽  
Neutron Source ◽  
316L Stainless Steel ◽  
Spallation Neutron Source ◽  
Aisi 316L ◽  
Aisi 316L Stainless Steel
Sign in / Sign up

Export Citation Format

Share Document