scholarly journals Three-dimensional computational fluid dynamics for the Spallation Neutron Source liquid mercury target

1998 ◽  
Author(s):  
M.W. Wendel ◽  
M. Siman-Tov
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Neutron Source ◽  
Three Dimensional ◽  
Spallation Neutron Source ◽  
Liquid Mercury

Improving Computational Fluid Dynamics Simulations for the Spallation Neutron Source Jet-Flow Target

2016 ◽  
Author(s):  
C. Barbier ◽  
E. Dominguez-Ontiveros
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Neutron Source ◽  
Jet Flow ◽  
Computational Time ◽  
Spallation Neutron Source ◽  
Mean Flow ◽  
Cfd Simulations ◽  
Flow Measurements ◽  
Piv Measurements

A liquid mercury target is used at Oak Ridge National Laboratory’s (ORNL [1]) Spallation Neutron Source (SNS [2]) to generate neutrons. The mercury is flowing in a stainless steel containment vessel for neutron spallation, but also to cool the vessel itself. Computational Fluid Dynamics (CFD) simulations have been used to estimate the temperature and pressure fields needed for the thermal stress analysis. Because of the geometry complexity, the high turbulence number, and the computational time requirements, generating a quality mesh that can accurately capture the flow and heat transfer has always been a challenge. However, with today’s High Performance Computing (HPC) advances, larger and larger meshes can now be used and better accuracy can be achieved. In this study, two meshing methods were used for the SNS jet-flow target: automatic tetrahedral method (ANSYS meshing) and manual hexahedral meshing (ICEM-CFD). Both methods are compared in terms of quality, size, ease of generation, convergence, and user-friendliness. Both meshes were used with ANSYS-CFX to simulate the steady, Newtonian, single phase, isothermal, incompressible and turbulent flow in the target. The Shear Stress Transport (SST) k-ω model developed by Menter [3] was used for turbulence modeling. The accuracy of the CFD simulations are tested against experimental data presented in the current paper. An in-depth series of Particle Image Velocimetry (PIV) measurements performed on a “visual jet-flow target”, an acrylic replica target running with water, are presented in the paper. Since flow measurements in mercury are difficult, a water loop was built to investigate the flow in the target and a potential gas injection in the flow to mitigate the pressure wave [4]. A PIV system on a precise translation stage was setup on the water loop to perform detailed and accurate PIV measurements. Mean flow velocity fields were used to validate the CFD simulations. The paper concludes on the choice for mesh generation for future target analysis, and the path forward for CFD simulations for the future SNS targets.

scholarly journals Computational Analysis to Factor Wind into the Design of an Architectural Environment

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Hassam Nasarullah Chaudhry ◽  
John Kaiser Calautit ◽  
Ben Richard Hughes
Keyword(s):  
Fluid Dynamics ◽  
Power Generation ◽  
Computational Fluid Dynamics ◽  
Three Dimensional ◽  
Numerical Data ◽  
Navier Stokes ◽  
Windward Side ◽  
Average Value ◽  
Continuity Equations ◽  
Prevailing Wind Direction

The effect of wind distribution on the architectural domain of the Bahrain Trade Centre was numerically analysed using computational fluid dynamics (CFD). Using the numerical data, the power generation potential of the building-integrated wind turbines was determined in response to the prevailing wind direction. The three-dimensional Reynolds-averaged Navier-Stokes (RANS) equations along with the momentum and continuity equations were solved for obtaining the velocity and pressure field. Simulating a reference wind speed of 6 m/s, the findings from the study quantified an estimate power generation of 6.4 kW indicating a capacity factor of 2.9% for the benchmark model. At the windward side of the building, it was observed that the layers of turbulence intensified in inverse proportion to the height of the building with an average value of 0.45 J/kg. The air velocity was found to gradually increase in direct proportion to the elevation with the turbine located at higher altitude receiving maximum exposure to incoming wind. This work highlighted the potential of using advanced computational fluid dynamics in order to factor wind into the design of any architectural environment.

scholarly journals Numerical Simulation and Analysis on Spray Drift Movement of Multirotor Plant Protection Unmanned Aerial Vehicle

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2399 ◽  
Author(s):  
Fengbo Yang ◽  
Xinyu Xue ◽  
Chen Cai ◽  
Zhu Sun ◽  
Qingqing Zhou
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Droplet Size ◽  
Wind Field ◽  
Flow Model ◽  
Two Phase Flow ◽  
Plant Protection ◽  
Three Dimensional ◽  
Phase Flow ◽  
Two Phase

In recent years, multirotor unmanned aerial vehicles (UAVs) have become more and more important in the field of plant protection in China. Multirotor unmanned plant protection UAVs have been widely used in vast plains, hills, mountains, and other regions, and become an integral part of China’s agricultural mechanization and modernization. The easy takeoff and landing performances of UAVs are urgently required for timely and effective spraying, especially in dispersed plots and hilly mountains. However, the unclearness of wind field distribution leads to more serious droplet drift problems. The drift and distribution of droplets, which depend on airflow distribution characteristics of UAVs and the droplet size of the nozzle, are directly related to the control effect of pesticide and crop growth in different growth periods. This paper proposes an approach to research the influence of the downwash and windward airflow on the motion distribution of droplet group for the SLK-5 six-rotor plant protection UAV. At first, based on the Navier-Stokes (N-S) equation and SST k–ε turbulence model, the three-dimensional wind field numerical model is established for a six-rotor plant protection UAV under 3 kg load condition. Droplet discrete phase is added to N-S equation, the momentum and energy equations are also corrected for continuous phase to establish a two-phase flow model, and a three-dimensional two-phase flow model is finally established for the six-rotor plant protection UAV. By comparing with the experiment, this paper verifies the feasibility and accuracy of a computational fluid dynamics (CFD) method in the calculation of wind field and spraying two-phase flow field. Analyses are carried out through the combination of computational fluid dynamics and radial basis neural network, and this paper, finally, discusses the influence of windward airflow and droplet size on the movement of droplet groups.

scholarly journals Three-Dimensional Aerodynamic Analysis of a Darrieus Wind Turbine Blade Using Computational Fluid Dynamics and Lifting Line Theory

2017 ◽  
Author(s):  
Francesco Balduzzi ◽  
Alessandro Bianchini ◽  
Giovanni Ferrara ◽  
David Marten ◽  
George Pechlivanoglou ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Performance ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Cost Effective ◽  
Navier Stokes ◽  
Line Theory ◽  
Wake Model ◽  
Lifting Line

Due to the rapid progress in high-performance computing and the availability of increasingly large computational resources, Navier-Stokes computational fluid dynamics (CFD) now offers a cost-effective, versatile and accurate means to improve the understanding of the unsteady aerodynamics of Darrieus wind turbines and deliver more efficient designs. In particular, the possibility of determining a fully resolved flow field past the blades by means of CFD offers the opportunity to both further understand the physics underlying the turbine fluid dynamics and to use this knowledge to validate lower-order models, which can have a wider diffusion in the wind energy sector, particularly for industrial use, in the light of their lower computational burden. In this context, highly spatially and temporally refined time-dependent three-dimensional Navier-Stokes simulations were carried out using more than 16,000 processor cores per simulation on an IBM BG/Q cluster in order to investigate thoroughly the three-dimensional unsteady aerodynamics of a single blade in Darrieus-like motion. Particular attention was payed to tip losses, dynamic stall, and blade/wake interaction. CFD results are compared with those obtained with an open-source code based on the Lifting Line Free Vortex Wake Model (LLFVW). At present, this approach is the most refined method among the “lower-fidelity” models and, as the wake is explicitly resolved in contrast to BEM-based methods, LLFVW analyses provide three-dimensional flow solutions. Extended comparisons between the two approaches are presented and a critical analysis is carried out to identify the benefits and drawbacks of the two approaches.

scholarly journals Three-Dimensional Aerodynamic Analysis of a Darrieus Wind Turbine Blade Using Computational Fluid Dynamics and Lifting Line Theory

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Francesco Balduzzi ◽  
David Marten ◽  
Alessandro Bianchini ◽  
Jernej Drofelnik ◽  
Lorenzo Ferrari ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Performance ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Cost Effective ◽  
Navier Stokes ◽  
Line Theory ◽  
Wake Model ◽  
Lifting Line

Due to the rapid progress in high-performance computing and the availability of increasingly large computational resources, Navier–Stokes (NS) computational fluid dynamics (CFD) now offers a cost-effective, versatile, and accurate means to improve the understanding of the unsteady aerodynamics of Darrieus wind turbines and deliver more efficient designs. In particular, the possibility of determining a fully resolved flow field past the blades by means of CFD offers the opportunity to both further understand the physics underlying the turbine fluid dynamics and to use this knowledge to validate lower-order models, which can have a wider diffusion in the wind energy sector, particularly for industrial use, in the light of their lower computational burden. In this context, highly spatially and temporally refined time-dependent three-dimensional (3D) NS simulations were carried out using more than 16,000 processor cores per simulation on an IBM BG/Q cluster in order to investigate thoroughly the 3D unsteady aerodynamics of a single blade in Darrieus-like motion. Particular attention was paid to tip losses, dynamic stall, and blade/wake interaction. CFD results are compared with those obtained with an open-source code based on the lifting line free vortex wake model (LLFVW). At present, this approach is the most refined method among the “lower-fidelity” models, and as the wake is explicitly resolved in contrast to blade element momentum (BEM)-based methods, LLFVW analyses provide 3D flow solutions. Extended comparisons between the two approaches are presented and a critical analysis is carried out to identify the benefits and drawbacks of the two approaches.

Sign in / Sign up

Export Citation Format

Share Document