Application of a Simplified Approach to GE Detector System Calibration

2003 ◽  
Author(s):  
R. Leicht ◽  
G. G. Simon
Keyword(s):  
Gamma Spectroscopy ◽  
Rotational Symmetry ◽  
Polar Angle ◽  
Radioactive Material ◽  
Wall Material ◽  
Detector Response ◽  
Calibration Data ◽  
Gamma Energy ◽  
Simplified Approach ◽  
Wide Range

Basic tasks in all monitoring projects involving gamma spectroscopy are design optimization and calibration of the Ge gamma spectrometer system which in general consists of one or more Ge detectors, the corresponding collimators, and the object with radioactive material (container, drum, wall, material on a conveyor etc.). A simplified approach to these problems has been developed by RWE NUKEM GmbH, leading to the software tool “ISO-Mod” which provides a straightforward comprehensive approach for the assessment and analysis of the most common cases without any need for other resources. The detector response is measured with calibration sources as a function of gamma energy, distance and polar angle. The effect of collimators is evaluated for rotational symmetry and for rectangular design based on polygon cross sections, with the possibility to have one or more layers of specific materials. The object model allows considering cubic (e. g. box, material on conveyor) or cylindrical (e. g. drum) absorption matrix and activity distributions with additional optional absorption layers. For considering the absorption in the object matrix and in the collimator material, mass attenuation coefficients are available for a wide range of energy. A number of selected gamma energies and matrix densities can be evaluated in a single evaluation run using Point Kernel and Monte Carlo simulation methods. For selected energies and densities, ISO-Mod provides the probability distribution of the calibration data. This allows investigating the sensitivity to potentially non-homogeneous activity distributions, e. g. to assess the improvement achieved when using more than one detector since up to 4 detectors can be considered simultaneously. All design data and results are — hierarchically structured — stored in a particular database. ISO-Mod is currently being used in different monitoring projects involving conveyor belts, containers and drums with radioactive material. Good agreement was found between the calculations and the results of measurements using calibrated point and homogeneous extended volume sources. Particular procedures are applied for locating hot spots in waste packages with multi-detector systems.

Influence of Longitudinal Roughness on Friction in EHL Contacts

2004 ◽  
Vol 126 (3) ◽  
pp. 473-481 ◽  
Author(s):  
B. Jacod ◽  
C. H. Venner ◽  
P. M. Lugt
Keyword(s):  
Numerical Simulations ◽  
Operating Conditions ◽  
Simplified Approach ◽  
Curve Fit ◽  
Longitudinal Roughness ◽  
Wide Range ◽  
Equivalent Wave ◽  
Harmonic Components ◽  
Comparison Of The Results ◽  
Relative Friction

The effect of longitudinal roughness on the friction in EHL contacts is investigated by means of numerical simulations. In the theoretical model the Eyring equation is used to describe the rheological behavior of the lubricant. First the relative friction variation caused by a single harmonic roughness component is computed as a function of the amplitude and wavelength for a wide range of operating conditions. From the results a curve fit formula is derived for the relative friction variation as a function of the out-of-contact geometry of the waviness and a newly derived parameter characterizing the response of the lubricant to pressure variations. Subsequently, the case of a superposition of two harmonic components is considered. It is shown that for the effect on friction such a combined pattern can be represented by a single equivalent wave. The amplitude and the wavelength of the equivalent wave can be determined from a nonlinear relation in terms of the amplitudes and wavelengths of the individual harmonic components. Finally the approach is applied to the prediction of the effect of a real roughness profile (many components) on the friction. From a comparison of the results with full numerical simulations it appears that the simplified approach is quite accurate.

Optimized liquid-chromatographic determination of metronidazole and its metabolites in plasma.

1984 ◽  
Vol 30 (5) ◽  
pp. 784-787 ◽  
Author(s):  
R A Gibson ◽  
L Lattanzio ◽  
H McGee
Keyword(s):  
Rapid Determination ◽  
Chromatographic Determination ◽  
Reversed Phase ◽  
Detector Response ◽  
High Pressure Liquid Chromatographic ◽  
Liquid Chromatographic Method ◽  
Wide Range ◽  
Liquid Chromatographic Determination ◽  
Liquid Chromatographic

Abstract Metronidazole and its known metabolites in plasma can be rapidly separated by a "high-pressure" liquid-chromatographic method that can also be adapted for rapid determination of tinidazole. Samples deproteinized with trichloroacetic acid (50 g/L final concentration) undergo isocratic separation on a reversed-phase C18 column eluted with an 8/92 (by vol) mixture of acetonitrile/KH2PO4 (5 mmol/L, pH 3.0). The method is sensitive, reliably detecting as little as 25 micrograms of metronidazole and (or) its metabolites per milliliter of plasma. The detector response varied linearly with concentration for all compounds tested over a wide range (25-500 micrograms/L). Within-day and between-day variation was generally less than 2.5% for all concentrations of all compounds tested. Various other antibiotics tested did not interfere.

scholarly journals Conditional Wasserstein Generative Adversarial Networks for Fast Detector Simulation

2021 ◽  
Vol 251 ◽  
pp. 03055
Author(s):  
John Blue ◽  
Braden Kronheim ◽  
Michelle Kuchera ◽  
Raghuram Ramanujan
Keyword(s):  
High Energy Physics ◽  
High Energy ◽  
Generative Models ◽  
Generative Adversarial Networks ◽  
Detector Response ◽  
Event Simulation ◽  
Simulation Process ◽  
Adversarial Networks ◽  
Wide Range ◽  
Detector Simulation

Detector simulation in high energy physics experiments is a key yet computationally expensive step in the event simulation process. There has been much recent interest in using deep generative models as a faster alternative to the full Monte Carlo simulation process in situations in which the utmost accuracy is not necessary. In this work we investigate the use of conditional Wasserstein Generative Adversarial Networks to simulate both hadronization and the detector response to jets. Our model takes the 4-momenta of jets formed from partons post-showering and pre-hadronization as inputs and predicts the 4-momenta of the corresponding reconstructed jet. Our model is trained on fully simulated tt events using the publicly available GEANT-based simulation of the CMS Collaboration. We demonstrate that the model produces accurate conditional reconstructed jet transverse momentum (pT) distributions over a wide range of pT for the input parton jet. Our model takes only a fraction of the time necessary for conventional detector simulation methods, running on a CPU in less than a millisecond per event.

Simplified approach to confidence limited in radioimmunassay.

1980 ◽  
Vol 26 (6) ◽  
pp. 763-765 ◽  
Author(s):  
R C Baxter
Keyword(s):  
Quality Control ◽  
Mean Value ◽  
Confidence Limits ◽  
Simple Method ◽  
Response Variable ◽  
Simplified Approach ◽  
Quadratic Curve ◽  
Wide Range ◽  
Advanced Computing ◽  
Routine Quality Control

Abstract A simple method of calculating confidence limits for radioimmunoassay data is presented. The method involves the use of the within-assay variation in dose estimate of three routine quality-control specimens, measured in repeated assays, to estimate the confidence limits for results on unknown samples. Results for control specimens are combined by calculating the unique quadratic curve fitting a graph of within-assay standard deviation vs mean value for each control. This method requires no special data accumulation or advanced computing equipment. For cortisol, lutropin, and thyroxine radioimmunoassays, confidence limits calculated in this way have been compared with those calculated from the variance of the response variable “B/B0” in repeated standard curves. Both methods agree well with actual limits observed when plasma pools containing a wide range of hormone concentrations are assayed repeatedly.

scholarly journals Factors affecting the consumption of fuel and energy resources during the construction of monolithic buildings

2020 ◽  
Vol 164 ◽  
pp. 08020
Author(s):  
Oleg Korol
Keyword(s):  
Average Energy ◽  
Energy Resources ◽  
Factors Affecting ◽  
Simplified Approach ◽  
Master Plans ◽  
Construction Organizations ◽  
Wide Range ◽  
Expert Assessments ◽  
Technological Documentation ◽  
Technological Modeling

The organization of work at the construction site is regulated by the calculated indicators of the consumption of fuel and energy resources. In the process of solving the problems of organizational and technological modeling, factors are determined that, to varying degrees, affect the reduction in the consumption of fuel and energy resources during construction and installation works. The purpose of the study is to determine the factors that affect the reduction of fuel and energy resources at the stage of organizational and technological design. We used the method of expert assessments, method of a simplified approach to average energy costs for individual types of consumers for a certain period of work, specific indicators of the consumption of certain types of resources in a wide range are used. When developing calendar plans and building master plans as part of the organizational and technological documentation, a methodology for summarizing and consolidating a number of indicators is used, most of which have no quantitative measurement. As the results, the variation coefficients are determined for the factors to ensure the activities of construction organizations in the field of energy conservation and energy efficiency.

The Application of a Two-Dimensional Zone Model to the Design and Control of a Continuously Operated, Gas-Fired Furnace

2002 ◽  
Author(s):  
Sara A. C. Correia ◽  
John Ward
Keyword(s):  
Dynamics Simulation ◽  
Relative Mass ◽  
Zone Model ◽  
Two Dimensional ◽  
Furnace Design ◽  
Simplified Approach ◽  
Flow Models ◽  
Discharge Temperature ◽  
Wide Range ◽  
And Control

This paper describes the development of a two-dimensional zone model to predict the throughput and thermal performance of a continuously operated gas-fired furnace heating steel bars to a nominal discharge temperature of 1250°C. Ultimately the model is intended to be a tool which can be used for the design and control of industrial furnaces. Consequently relatively short computing times are necessary and this was achieved by employing an isothermal computational fluid dynamics simulation to estimate the relative mass flows, and hence enthalpy flows to or from adjacent volume zones in the overall model. This simplified approach, which utilises a single “once off” isothermal computation of the flows, was considered to be adequate since isothermal flow models have been used successfully in the past to study the flow related behaviour of combustion systems. The coupling of a multi-zone model with a single “once off” isothermal computation of the flows enables a wide range of furnace design modifications to be studied quickly and easily. To illustrate the potential use of the model in a furnace design application, it was then used to investigate the effects of inclining the burners downwards towards the load as well as those associated with increasing the length of the furnace.

3-E Analysis of a Heat Pump Driven by a Micro-Cogenerator

2005 ◽  
Author(s):  
Maurizio Sasso ◽  
Raffaello Possidente ◽  
Carlo Roselli ◽  
Sibilio Sergio
Keyword(s):  
Heat Pump ◽  
Thermal Energy ◽  
Primary Energy ◽  
Operating Conditions ◽  
Environmental Benefits ◽  
Test Facility ◽  
Cooling Mode ◽  
Simplified Approach ◽  
Wide Range ◽  
Network Losses

The cogeneration, or the combined production of electric (and/or mechanical) and thermal energy, is a well established technology, which has important environmental benefits and it has been noted by the European Community as one of the first elements to save primary energy, to avoid network losses and to reduce the greenhouse gas emissions. In particular, the study will be focused on the micro-cogeneration process with micro-combined heat and power system, or MCHP (electric power output ≤ 15 kW), which represents a valid and interesting application of this technology applicable, above all, to residential and light commercial users. This paper presents the Energy, Economic and Environmental (3-E) analysis of a natural gas-fired MCHP in combination with an electric heat pump (EHP). The 3-E analysis of the MCHP/EHP begins with the results of a detailed experimental activity developed in a test facility [1] for a wide range of conditions. Two operating conditions were simulated: a heating mode with co-production of electric and thermal energy, and a cooling mode with co-production of electric, thermal and cooling energy (tri-generation). The annual operating performance, also based on the typical features of the Italian market, is also discussed with a simplified approach.

Measurement of Total Water with a Tunable Diode Laser Hygrometer: Inlet Analysis, Calibration Procedure, and Ice Water Content Determination

2007 ◽  
Vol 24 (3) ◽  
pp. 463-475 ◽  
Author(s):  
Sean M. Davis ◽  
A. Gannet Hallar ◽  
Linnea M. Avallone ◽  
William Engblom
Keyword(s):  
Particle Size ◽  
Water Vapor ◽  
Water Content ◽  
Diode Laser ◽  
Tunable Diode Laser ◽  
Calibration Data ◽  
Total Water ◽  
Wide Range ◽  
Ice Water Content ◽  
Ice Water

Abstract The University of Colorado closed-path tunable diode laser hygrometer (CLH), a new instrument for the in situ measurement of enhanced total water (eTW, the sum of water vapor and condensed water enhanced by a subisokinetic inlet), has recently been flown aboard the NASA DC-8 and WB-57F aircrafts. The CLH has the sensitivity necessary to quantify the ice water content (IWC) of extremely thin subvisual cirrus clouds (∼0.1 mg m−3), while still providing measurements over a large range of conditions typical of upper-tropospheric cirrus (up to 1 g m−3). A key feature of the CLH is its subisokinetic inlet system, which is described in detail in this paper. The enhancement and evaporation of ice particles that results from the heated subisokinetic inlet is described both analytically and based on computational fluid dynamical simulations of the flow around the aircraft. Laboratory mixtures of water vapor with an accuracy of 2%–10% (2σ) were used to calibrate the CLH over a wide range of water vapor mixing ratios (∼50–50 000 ppm) and pressures (∼100–1000 mb). The water vapor retrieval algorithm, which is based on the CLH instrument properties as well as on the spectroscopic properties of the water absorption line, accurately fits the calibration data to within the uncertainty of the calibration mixtures and instrument signal-to-noise ratio. A method for calculating cirrus IWC from the CLH enhanced total water measurement is presented. In this method, the particle enhancement factor is determined from an independent particle size distribution measurement and the size-dependent CLH inlet efficiency. It is shown that despite the potentially large uncertainty in particle size measurements, the error introduced by this method adds ∼5% error to the IWC calculation. IWC accuracy ranges from 20% at the largest IWC to 50% at small IWC (<5 mg m−3).

scholarly journals Polarization data from SCIAMACHY limb backscatter observations compared to vector radiative transfer model simulations

2013 ◽  
Vol 6 (6) ◽  
pp. 1503-1520 ◽  
Author(s):  
P. Liebing ◽  
K. Bramstedt ◽  
S. Noël ◽  
V. Rozanov ◽  
H. Bovensmann ◽  
...  
Keyword(s):  
Radiative Transfer ◽  
Polarization Measurement ◽  
Radiative Transfer Model ◽  
Polarization Sensitivity ◽  
Transfer Model ◽  
Calibration Data ◽  
Radiometric Calibration ◽  
Polarization Data ◽  
Imaging Spectrometer ◽  
Wide Range

Abstract. SCIAMACHY is a passive imaging spectrometer onboard ENVISAT designed to obtain trace gas abundances from measured radiances and irradiances in the UV to SWIR range in nadir-, limb- and occultation-viewing modes. Its grating spectrometer introduces a substantial sensitivity to the polarization of the incoming light with nonnegligible effects on the radiometric calibration. To be able to correct for the polarization sensitivity, SCIAMACHY utilizes broadband Polarization Measurement Devices (PMDs). While for the nadir-viewing mode the measured atmospheric polarization has been validated against POLDER data (Tilstra and Stammes, 2007, 2010), a similar validation study regarding the limb-viewing mode has not yet been performed. This paper aims at an assessment of the quality of the SCIAMACHY limb polarization data. Since limb polarization measurements by other air/spaceborne instruments in the spectral range of SCIAMACHY are not available, a comparison with radiative transfer simulations by SCIATRAN V3.1 (Rozanov et al., 2013) using a wide range of atmospheric parameters is performed. SCIATRAN is a vector radiative transfer model (VRTM) capable of performing calculations of the multiply scattered radiance in a spherically symmetric atmosphere. The study shows that the limb polarization data exhibit a large time-dependent bias that decreases with wavelength. Possible reasons for this bias are a still unknown combination of insufficient accuracy or inconsistencies of the on-ground calibration data, scan mirror degradation and stress induced changes of the polarization response of components inside the optical bench of the instrument. It is shown that it should in principle be feasible to recalibrate the effective polarization sensitivity of the instrument using the in-flight data and VRTM simulations.

Development of a Capacitance Based Void Fraction Sensor for Two-Phase Flow Measurements

2013 ◽  
Author(s):  
Rodward L. Hewlin ◽  
John P. Kizito
Keyword(s):  
Void Fraction ◽  
Two Phase Flow ◽  
Full Range ◽  
Working Fluid ◽  
Phase Flow ◽  
Calibration Data ◽  
Two Phase ◽  
Flow Measurements ◽  
Static Calibration ◽  
Wide Range

The aim of this paper was to develop a capacitance based sensor capable of measuring void fraction in a continuous two-phase flow field. The design methodology and operation of the capacitance based void fraction sensor is discussed. Two designs of capacitance void fraction sensors were developed and tested. Some of the problems associated with the first were identified and a new sensor electrode configuration was developed which presented a more sensitive and repeatable response. Data was collected covering a wide range of void fraction measurements ranging from 0 to 1 for water as the working fluid. Calibration of the sensor required that the air gap or void capacitance (dry signal) be measured followed by an increase in liquid levels (wet signal) to obtain a range of void fraction measurements for static calibration. The static calibration data obtained was nonlinear for the full range of void fraction measurements for water. This paper covers the design requirements, calibration procedure and static calibration data obtained for the developed sensor, and dynamic void fraction data measurements. The sensor was tested in both a horizontal and vertical orientation and proved to be orientation insensitive. The experimental results are promising for water and verify successful operation for measuring void fraction in continuous two-phase flows.

Sign in / Sign up

Export Citation Format

Share Document