Comparison of Bio-Fischer-Tropsch Fuel and Commercial Diesel Fuel Application in a 1600 CC Euro 5 Diesel Engine

2015 ◽  
Author(s):  
Claus Suldrup Nielsen ◽  
Jesper Schramm ◽  
Anders Ivarsson ◽  
Azhar Malik ◽  
Terese Løvås
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Steady State ◽  
Diesel Engine ◽  
Carbon Dioxide Emissions ◽  
Operating Conditions ◽  
Injection Timing ◽  
Nox Emissions ◽  
Fischer Tropsch ◽  
Operating Range

A direct injected and turbocharged Euro 5 diesel engine has been set up in a test bench where the vehicle driving conditions of the European NEDC (New European Driving Cycle) test can be simulated. The engine is operated as the engine of a corresponding vehicle, equipped with a similar engine and driving through the NEDC cycle. The regulated gaseous emissions, carbon monoxide, hydrocarbons and nitrogen oxides, as well as particulate numbers and size distributions where measured in 5 selected steady state operating points during the engine test. Fuel consumptions and carbon dioxide emissions where measured as well. The steady state operating conditions were chosen within the engine operating range during a vehicle NEDC test and representing as broad an operating range as possible during the NEDC test. A method is presented in which the NEDC test emissions are calculated from the 5 steady state measurements. It is shown that the method gives emission results that agree well with values that can be expected from the vehicle in question during an NEDC test. In this way a limited number of steady state measurements can be used to simulate vehicle emissions. The reason for carrying out engine experiments instead of vehicle measurements was to obtain well controlled engine conditions and thus better insight in the operation of the engine in the individual phases of operation, and thereby enable evaluation of the possibilities for improving engine performance with respect to emission and fuel consumption reduction. Two different fuels where tested. These were a Fischer-Tropsch fuel, produced from biomass at the Güssing gasification plant in Austria and a commercial diesel from a fuel station in Denmark. The results of the measurements and engine modification considerations showed that bio Fischer-Tropsch fuel does have advantages with respect to particulate and also small advantages with carbon monoxide and carbon dioxide emissions. However, NOx emissions are rather a question of the injection timing of the fuel, and the NOx emissions can be adjusted to give the same level of emissions by changing the injection timing with ordinary diesel. The injection strategy was changed in order to attempt to reduce NOx emissions below the limits in the Euro 6 regulations.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

A Study of the Effects of Biofuel Use on Piston Lubrication During Fuel Post Injection in a Direct Injection Diesel Engine

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Koji Kikuhara ◽  
Akihiro Shibata ◽  
Akemi Ito ◽  
Dallwoo Kim ◽  
Yasuhiro Ishikawa ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Diesel Engine ◽  
Diesel Engines ◽  
Carbon Dioxide Emissions ◽  
Operating Conditions ◽  
Fuel Oil ◽  
Cylinder Wall ◽  
Post Injection ◽  
Friction Forces ◽  
Lubrication Condition

The reduction of both exhaust gases and carbon dioxide emissions is necessary to meet future emissions regulations for diesel engines. Exhaust after-treatment devices are gradually being applied to diesel engines to reduce exhaust gases. Diesel particulate filters (DPF), an after-treatment device for diesel engines, in some cases require fuel post injection for regeneration. Post injection is usually conducted at the midpoint of the expansion stroke, and therefore causes fuel adhesion to the cylinder wall. However, using biofuels in a diesel engine is an effective way of reducing carbon dioxide emissions. It is well known that biofuels are chemically unstable, but the effects of biofuels on piston lubrication condition have not been thoroughly studied. In this study, piston lubrication condition during post injection in a single cylinder DI diesel engine using biofuel was investigated. Piston and ring friction forces were measured under engine operating conditions by means of a floating liner device to investigate the lubrication condition of the piston and rings. Both light fuel oil and biofuel were used in the measurements, with rapeseed methyl ester (RME) being used as the biofuel. Lubricating oil on the cylinder wall was also sampled under engine operating conditions, and the effect of post injection on fuel adhesion to the cylinder wall was analyzed. It was found that the effect of post injection on fuel adhesion to the cylinder wall was remarkable around the top dead center (TDC), and the fuel dilution rate reached approximately 90%. The results of the measurement of the piston friction forces showed that post injection caused an increase in the friction forces at the compression TDC (CTDC) in the cases of both RME and light fuel oil, and the friction forces at CTDC increased according to the delay of the post injection timing. The increase in the piston friction forces was moderate in the case of RME. It seems that the higher viscosity and the oiliness of RME suppressed the increase in piston friction forces at TDC. The following effects were found in this study. Fuel post injection caused fuel adhesion to the cylinder wall. Such phenomena affected the lubrication condition of the piston. In the case of RME, the increase in the piston friction forces caused by post injection was smaller than that of light fuel oil, but the effects on piston lubrication condition in the case of using other biofuels needs to be investigated.

scholarly journals Experimental Study of Injection Parameters on the Performance of a Diesel Engine with Fischer–Tropsch Fuel Synthesized from Coal

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3280 ◽  
Author(s):  
Jinhong Shi ◽  
Tie Wang ◽  
Zhen Zhao ◽  
Tiantian Yang ◽  
Zhengwu Zhang
Keyword(s):  
Diesel Engine ◽  
Combustion Process ◽  
Injection Pressure ◽  
Injection Timing ◽  
Nox Emissions ◽  
Cylinder Pressure ◽  
Fischer Tropsch ◽  
Ignition Point ◽  
Injection Parameters ◽  
Combustion Emissions

Experimental research was conducted on a turbo-charged, inter-cooling and common-rail diesel engine with Fischer–Tropsch fuel synthesized from Coal-to-liquid (CTL), in order to investigate the influence of different injection parameters on the combustion, emissions and efficiency characteristics of the engine. The results showed that the ignition point was advanced, the in-cylinder pressure and heat release rate increased as the injection timing advanced and the injection pressure increased. By comparing the peak in-cylinder pressure of 100 cycles for one sample, it was found that the coefficient variation (COV) remained under 2% throughout the tests and the combustion process remained stable. NOx emissions decreased with delayed injection timing and lower injection pressure. In contrast to NOXNOx emissions, soot emissions were almost zero when the injection pressure was up to 143.5 MPa. The indicated thermal efficiency (ITE) showed no obvious change with different injection parameters, and remained under 40% in all the tests.

scholarly journals Assessing the Effects of Engine Load on Compression Ignition Engines Using Biodiesel Blends

2021 ◽  
Author(s):  
Semakula Maroa ◽  
Freddie Inambao
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Diesel Engine ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Waste Plastic ◽  
Compression Ignition Engines ◽  
Carbon Dioxide Co2

This study evaluated the performance of a diesel engine operated with waste plastic biodiesel fuel (WPPO) blends. Findings were that at all engine loads (from idling to full load) the emissions of carbon monoxide (CO), unburnt hydrocarbon (UHC) and carbon dioxide (CO2) were low compared to conventional diesel (PD), although the emissions of NOX were higher. The brake specific fuel consumption (BSFC) for the blends dropped while the brake thermal efficiency (BTE) increased with load for all blends until intermediate load when it decreased. WPPO blends had a higher viscosity compared to PD. CO emissions for blend 95/WPPO5 at all engine speed idling modes were 285 ppm, 298 ppm, 320ppm, and 388 ppm while PD emissions were 270 ppm, 295 ppm, 315 ppm and 365 ppm respectively. The values for UHC for blend 95/WPPO5 at all modes were 35 ppm, 28 ppm, 22 ppm, and 18 ppm compared to PD fuel with 20ppm, 25 ppm, 30 ppm, and 40ppm respectively. The NOX emissions for PD fuel at all modes were 175 ppm, 225 ppm, 300 ppm and 375 ppm compared to blend 95/WPPO5 at 195 ppm, 245 ppm, 335 ppm, and 397 ppm. The BSFC values for blend 95/WPPO5 at all modes were 0.48 kg/kW.h, 0.41 kg/kW.h, 0.35 kg/kW.h and 0.4 kg/kW.h compared to PD at 0.45 kg/kW.h, 0.39 kg/kW.h, 0.33 kg/kW.h and 035 kg/kW.h respectively.

Comparison of Emission Levels of Motor Cars, Motorcycles, and Tricycles Using Petrol Engines in Southwestern Nigeria

2021 ◽  
Vol 900 ◽  
pp. 183-187
Author(s):  
Odunlami Olayemi Abosede ◽  
Akeredolu Funso Alaba
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Carbon Dioxide Emissions ◽  
Mean Value ◽  
Southwestern Nigeria ◽  
Mean Values ◽  
Mobile Sources ◽  
Southwest Nigeria ◽  
The Mean ◽  
European Standards

The emissions of carbon monoxide, carbon dioxide, and hydrocarbon from four stroke-powered motorcars and two stroke-powered motorcycles and tricycles in Southwest Nigeria were examined using an automotive 4-gas analyer. Results show that tricycles produced more hydrocarbon and carbon monoxide emissions than motorcycles, while motorcycles emitted more of these pollutants than the gasoline fueled motor cars. (The gasoline fueled motorcars produced lowest hydrocarbon and carbon monoxide while the tricycles produced the highest hydrocarbon and carbon monoxide emissions). On the contrary, motor cars had the highest mean value of carbon dioxide followed by the motorcycles, while tricycles had the least. This could be attributed to the presence of the catalytic converters in some of the motor cars oxidizing carbon monoxide to carbon dioxide. The mean values of hydrocarbon, carbon monoxide and carbon dioxide emissions from motorcars are 630ppm, 10200ppm and 59900ppm. This is much higher than the NESREA (National Environmental standards and Regulations Enforcement Agency) standards as well as Euro II and Euro III (European standards) for vehicular emission. The mean values for hydrocarbon, carbon monoxide and carbon dioxide emissions from motorcycles and tricycles are (2150ppm, 21530ppm and 31200ppm) and (2820ppm, 24880ppm and 38710ppm) respectively. These results do not comply with Nigeria and European emission standards for hydrocarbon, and carbon monoxide. Tricycles and motorcycles account for higher concentrations of hydrocarbon and carbon monoxide pollutants from mobile sources, while they emit carbon dioxide minimally.

Ultra-Low Emission Hydrogen/Syngas Combustion With a 1.3 MW Injector Using a Micro-Mixing Lean-Premix System

2011 ◽  
Author(s):  
Brian Hollon ◽  
Erlendur Steinthorsson ◽  
Adel Mansour ◽  
Vincent McDonell ◽  
Howard Lee
Keyword(s):  
Carbon Dioxide ◽  
Natural Gas ◽  
Flame Temperature ◽  
Fuel Mixture ◽  
Full Scale ◽  
Operating Conditions ◽  
Nox Emissions ◽  
Fuel Injector ◽  
Nitrogen Dilution ◽  
Fuel Mixtures

This paper discusses the development and testing of a full-scale micro-mixing lean-premix injector for hydrogen and syngas fuels that demonstrated ultra-low emissions and stable operation without flashback for high-hydrogen fuels at representative full-scale operating conditions. The injector was fabricated using Macrolamination technology, which is a process by which injectors are manufactured from bonded layers. The injector utilizes sixteen micro-mixing cups for effective and rapid mixing of fuel and air in a compact package. The full scale injector is rated at 1.3 MWth when operating on natural gas at 12.4 bar (180 psi) combustor pressure. The injector operated without flash back on fuel mixtures ranging from 100% natural gas to 100% hydrogen and emissions were shown to be insensitive to operating pressure. Ultra-low NOx emissions of 3 ppm were achieved at a flame temperature of 1750 K (2690 °F) using a fuel mixture containing 50% hydrogen and 50% natural gas by volume with 40% nitrogen dilution added to the fuel stream. NOx emissions of 1.5 ppm were demonstrated at a flame temperature over 1680 K (2564 °F) using the same fuel mixture with only 10% nitrogen dilution, and NOx emissions of 3.5 ppm were demonstrated at a flame temperature of 1730 K (2650 °F) with only 10% carbon dioxide dilution. Finally, using 100% hydrogen with 30% carbon dioxide dilution, 3.6 ppm NOx emissions were demonstrated at a flame temperature over 1600 K (2420 °F). Superior operability was achieved with the injector operating at temperatures below 1470 K (2186 °F) on a fuel mixture containing 87% hydrogen and 13% natural gas. The tests validated the micro-mixing fuel injector technology and the injectors show great promise for use in future gas turbine engines operating on hydrogen, syngas or other fuel mixtures of various compositions.

Techno-Economic Evaluation of Pressurized Oxy-Fuel Combustion Systems

2010 ◽  
Author(s):  
Jongsup Hong ◽  
Ahmed F. Ghoniem ◽  
Randall Field ◽  
Marco Gazzino
Keyword(s):  
Carbon Dioxide ◽  
Carbon Dioxide Emissions ◽  
Power Plants ◽  
Carbon Dioxide Capture ◽  
Fuel Combustion ◽  
Economic Feasibility ◽  
Operating Conditions ◽  
Air Separation ◽  
Separation Unit ◽  
Coal Price

Oxy-fuel combustion coal-fired power plants can achieve significant reduction in carbon dioxide emissions, but at the cost of lowering their efficiency. Research and development are conducted to reduce the efficiency penalty and to improve their reliability. High-pressure oxy-fuel combustion has been shown to improve the overall performance by recuperating more of the fuel enthalpy into the power cycle. In our previous papers, we demonstrated how pressurized oxy-fuel combustion indeed achieves higher net efficiency than that of conventional atmospheric oxy-fuel power cycles. The system utilizes a cryogenic air separation unit, a carbon dioxide purification/compression unit, and flue gas recirculation system, adding to its cost. In this study, we perform a techno-economic feasibility study of pressurized oxy-fuel combustion power systems. A number of reports and papers have been used to develop reliable models which can predict the costs of power plant components, its operation, and carbon dioxide capture specific systems, etc. We evaluate different metrics including capital investments, cost of electricity, and CO2 avoidance costs. Based on our cost analysis, we show that the pressurized oxy-fuel power system is an effective solution in comparison to other carbon dioxide capture technologies. The higher heat recovery displaces some of the regeneration components of the feedwater system. Moreover, pressurized operating conditions lead to reduction in the size of several other critical components. Sensitivity analysis with respect to important parameters such as coal price and plant capacity is performed. The analysis suggests a guideline to operate pressurized oxy-fuel combustion power plants in a more cost-effective way.

scholarly journals Comparison of performance of biodiesels of mahua oil and gingili oil in dual fuel engine

2008 ◽  
Vol 12 (1) ◽  
pp. 151-156 ◽  
Author(s):  
Kapilan Nadar ◽  
Pratap Reddy ◽  
Rao Anjuri
Keyword(s):  
Carbon Monoxide ◽  
Methyl Ester ◽  
Dual Fuel ◽  
Injection Timing ◽  
Nox Emissions ◽  
Test Results ◽  
Liquefied Petroleum Gas ◽  
Mahua Oil ◽  
Hydro Carbon ◽  
Pilot Fuel

In this work, an experimental work was carried out to compare the performance of biodiesels made from non edible mahua oil and edible gingili oil in dual fuel engine. A single cylinder diesel engine was modified to work in dual fuel mode and liquefied petroleum gas was used as primary fuel. Biodiesel was prepared by transesterification process and mahua oil methyl ester (MOME) and gingili oil methyl ester (GOME) were used as pilot fuels. The viscosity of MOME is slightly higher than GOME. The dual fuel engine runs smoothly with MOME and GOME. The test results show that the performance of the MOME is close to GOME, at the pilot fuel quantity of 0.45 kg/h and at the advanced injection timing of 30 deg bTDC. Also it is observed that the smoke, carbon monoxide and unburnt hydro carbon emissions of GOME lower than the MOME. But the GOME results in slightly higher NOx emissions. From the experimental results it is concluded that the biodiesel made from mahua oil can be used as a substitute for diesel in dual fuel engine.

In-situ monitoring of carbon dioxide emissions from a diesel engine using a mid-infrared optical fibre sensor

2011 ◽  
Author(s):  
Elfed Lewis ◽  
John Clifford ◽  
Colin Fitzpatrick ◽  
Gerard Dooly ◽  
Weizhong Zhao ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Diesel Engine ◽  
Optical Fibre ◽  
Carbon Dioxide Emissions ◽  
In Situ Monitoring ◽  
Mid Infrared ◽  
Optical Fibre Sensor ◽  
Fibre Sensor

An Experimental Study on Smoke Reduction Effect of Post Injection in Combination With Pilot Injection for a Diesel Engine

2013 ◽  
Vol 136 (4) ◽  
Author(s):  
Long Liu ◽  
Naoto Horibe ◽  
Tatsuya Komizo ◽  
Issei Tamura ◽  
Takuji Ishiyama
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pilot Injection ◽  
Post Injection ◽  
Spray Flames ◽  
Injection Quantity ◽  
Main Injection ◽  
Reduction Effect

With the universal utilization of the common-rail injection system in automotive diesel engines, the multistage injection strategies have become typical approaches to satisfy the increasingly stringent emission regulations, and especially the post injection has received considerable attention as an effective way for reducing the smoke emissions. Normally the post injection is applied in combination with the pilot injection to restrain the NOx emissions, smoke emissions, and combustion noise simultaneously, and the pilot injection condition affects the combustion process of the main injection and might affect the smoke reduction effect of the post injection. Thus this study aims at obtaining the post injection strategy to reduce smoke emissions in a diesel engine, where post injection is employed in combination with pilot injection. The experiments were performed using a single-cylinder diesel engine under various conditions of pilot and post injection with a constant load at an IMEP of 1.01 MPa, fixed speed of 1500 rpm, and NOx emissions concentration of 150 ± 5 ppm that was maintained by adjusting the EGR ratio. The injection pressure was set at 90 MPa at first, and then it was varied to 125 MPa to evaluate the effects of post injection on the smoke reduction in the case of higher injection pressure. The experimental results show that small post injection quantity with a short interval from the end of main injection causes less smoke emissions. And larger pilot injection quantity and later pilot injection timing lead to higher smoke emissions. And then, to explore and interpret the smoke emissions tendencies with varying pilot and post injection conditions, the experimental results of three-stage injection conditions were compared to those of two reference cases, which only included the pilot and main injection, and the interaction between main spray flames and post sprays was applied for analysis. Based on the comparative analysis, the larger smoke reduction effect of post injection was observed with the larger pilot injection quantity, while it is not greatly influenced by pilot injection timing. In addition, the smoke emissions can be reduced considerably by increasing the injection pressure, however the smoke reduction effect of post injection was attenuated. And all of these tendencies were able to be interpreted by considering the intensity variation of the interaction between main spray flames and post sprays.

Sign in / Sign up

Export Citation Format

Share Document