scholarly journals Assessing the Effects of Engine Load on Compression Ignition Engines Using Biodiesel Blends

2021 ◽  
Author(s):  
Semakula Maroa ◽  
Freddie Inambao
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Diesel Engine ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Waste Plastic ◽  
Compression Ignition Engines ◽  
Carbon Dioxide Co2

This study evaluated the performance of a diesel engine operated with waste plastic biodiesel fuel (WPPO) blends. Findings were that at all engine loads (from idling to full load) the emissions of carbon monoxide (CO), unburnt hydrocarbon (UHC) and carbon dioxide (CO2) were low compared to conventional diesel (PD), although the emissions of NOX were higher. The brake specific fuel consumption (BSFC) for the blends dropped while the brake thermal efficiency (BTE) increased with load for all blends until intermediate load when it decreased. WPPO blends had a higher viscosity compared to PD. CO emissions for blend 95/WPPO5 at all engine speed idling modes were 285 ppm, 298 ppm, 320ppm, and 388 ppm while PD emissions were 270 ppm, 295 ppm, 315 ppm and 365 ppm respectively. The values for UHC for blend 95/WPPO5 at all modes were 35 ppm, 28 ppm, 22 ppm, and 18 ppm compared to PD fuel with 20ppm, 25 ppm, 30 ppm, and 40ppm respectively. The NOX emissions for PD fuel at all modes were 175 ppm, 225 ppm, 300 ppm and 375 ppm compared to blend 95/WPPO5 at 195 ppm, 245 ppm, 335 ppm, and 397 ppm. The BSFC values for blend 95/WPPO5 at all modes were 0.48 kg/kW.h, 0.41 kg/kW.h, 0.35 kg/kW.h and 0.4 kg/kW.h compared to PD at 0.45 kg/kW.h, 0.39 kg/kW.h, 0.33 kg/kW.h and 035 kg/kW.h respectively.

scholarly journals Determination of the optimal composition of mixed fuel based on the environmental performance of a diesel engine

2021 ◽  
Vol 1 (1) ◽  
pp. 14-22
Author(s):  
S.A. Plotnikov ◽  
◽  
Sh.V. Buzikov ◽  
I.S. Kozlov ◽  
◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Diesel Engine ◽  
Environmental Performance ◽  
Environmental Indicators ◽  
Effective Pressure ◽  
Bench Tests ◽  
Mixed Fuel ◽  
Unburned Hydrocarbons ◽  
Carbon Dioxide Co2

The use of rapeseed oil (RO) in tractor engines and other agricultural machinery in its pure form or a mixture of RO with diesel fuel (DF) imposes a number of limitations associated with some dif-ference in physical and chemical properties. Therefore, the most promising is the use of mixed fuel (MF) consisting of DF and RO. The purpose of these studies is to determine the optimal composi-tion of the MF, consisting of DF and RM by optimizing the approximated dependences of the envi-ronmental indicators of a diesel engine. To solve this problem, bench tests of the operation of the D-245.5S diesel engine (4ChN 11.0 / 12.5) were carried out. The following determined environmental performance indicators of a diesel engine are selected: soot (С), nitrogen oxides (NOx), unburned hydrocarbons (CxHy), carbon dioxide (CO2) and carbon monoxide (CO). The studies were carried out on various compositions of MF, consisting of 80% DF and 20% RO, 55% DF and 45% RO, 20% DF and 80% RO by weight, respectively. As a result of the bench tests, two load characteris-tics were obtained, the one at a speed of n = 1400 min-1 corresponding to the value of the maximum torque, and the second at a speed of n = 1800 min-1 corresponding to the value of the rated power, as well as the external speed characteristic of the D-245.5S tractor diesel engine (4ChN 11.0 / 12.5). The analysis of the obtained experimental data revealed the dependence of environmental indicators on the rotational speed of the diesel engine crankshaft, the average effective pressure and the addi-tion of RO in MF by weight. Using the least squares method, the approximated mathematical de-pendences of the ecological indicators of a diesel engine are determined. The analysis of the ob-tained dependencies showed that: the increase in the crankshaft speed n, the proportion of RO in MF and a decrease in the average effective pressure pe, leads to a decrease in soot С to 4.0%, nitro-gen oxides NOx to 100.0 ppm, unburned hydrocarbons CxHy to 1.0 ppm, carbon dioxide, CO2 up to 2%, and an increase in carbon monoxide CO up to 0.16%. As a result of solving the obtained system of equations for the approximated dependences of environmental indicators, the optimal addition of RO to MF of up to 35% by weight was determined.

scholarly journals Performance and exhaust gases of a diesel engine using different magnetic treatments of the fuel

2020 ◽  
Vol 14 (1) ◽  
pp. 6285-6294
Author(s):  
R. Arias Gilart ◽  
M. R. B. Ungaro ◽  
C. E. A. Rodríguez ◽  
J. F. F. Hernández ◽  
M. C. Sofia ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Diesel Engine ◽  
Compression Ratio ◽  
Engine Speed ◽  
Magnetic Treatment ◽  
Static Magnetic Fields ◽  
Mass Consumption ◽  
Exhaust Gases ◽  
Carbon Dioxide Co2

In this research, different magnetic treatments were applied to diesel fuel using static magnetic fields of 0.36T of magnetic induction. The magnetic conditioners (MCs) were installed in different positions of the fuel lines in the engine and the magnetic treatment of the diesel was also carried out before introducing it into the engine tanks. The study was conducted using a four-stroke, two-cylinder, Lister Petter (LPWS2) engine with a compression ratio of 23.5:1 and a constant engine speed of 1500 rpm. The emissions of carbon monoxide (CO), carbon dioxide (CO2), oxygen (O2), nitrogen oxides and the temperature of the exhaust gases and the mass consumption of fuel were measured. The highest levels of reduction were achieved with the magnetic treatments that locate the MC directly in the engine's pipes. As the number of MC in the engine pipes increases, the emissions of polluting gases decrease. With the treatment that locates one MC in front of each injector, two MC at the entrance of the filter and two MC in the return of fuel were able to increase the O2 emissions by 6.9% and decrease the CO emissions in about 21.3% in the last load of the generator set. With this treatment a decrease in fuel consumption of 4.89% to 80% of engine load was obtained.

scholarly journals Effectiveness of oxygen enriched hydrogen-HHO gas addition on DI diesel engine performance, emission and combustion characteristics

2014 ◽  
Vol 18 (1) ◽  
pp. 259-268 ◽  
Author(s):  
S.R. Premkartikkumar ◽  
K. Annamalai ◽  
A.R. Pradeepkumar
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Diesel Engine ◽  
Engine Performance ◽  
Water Electrolysis ◽  
Combustion Characteristics ◽  
Flow Rates ◽  
Brake Thermal Efficiency ◽  
Unburned Hydrocarbon ◽  
Di Diesel Engine

Nowadays, more researches focus on protecting the environment. Present investigation concern with the effectiveness of Oxygen Enriched hydrogen- HHO gas addition on performance, emission and combustion characteristics of a DI diesel engine. Here the Oxygen Enriched hydrogen-HHO gas was produced by the process of water electrolysis. When potential difference is applied across the anode and cathode electrodes of the electrolyzer, water is transmuted into Oxygen Enriched hydrogen-HHO gas. The produced gas was aspirated into the cylinder along with intake air at the flow rates of 1 lpm and 3.3 lpm. The results show that when Oxygen Enriched hydrogen-HHO gas was inducted, the brake thermal efficiency of the engine increased by 11.06%, Carbon monoxide decreased by 15.38%, Unburned hydrocarbon decreased by 18.18%, Carbon dioxide increased by 6.06%, however, the NOX emission increased by 11.19%.

Effects of Iron Nanoparticles Blended Biodiesel on the Performance and Emission Characteristics of a Diesel Engine

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
S. Debbarma ◽  
R. D. Misra
Keyword(s):  
Diesel Engine ◽  
Iron Nanoparticles ◽  
Specific Energy Consumption ◽  
Biodiesel Fuel ◽  
Emission Characteristics ◽  
Nox Emissions ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Fuel Blends ◽  
Suitable Modification

The technology for use of biodiesels (up to 20%) as alternative fuel in diesel engines has already been established. In this regard, some suitable modification of biodiesel with appropriate additives may help in increasing the biodiesel component in the biodiesel fuel blends. In order to evaluate the effects of iron nanoparticles (INP) blended palm biodiesel (PB) on the performance and emission characteristics of diesel engine, an experimental investigation is carried out in a single cylinder diesel engine. Methodically, biodiesel prepared from palm oil and commercially available nanosized INP is used in this study. Iron nanoparticles are suspended in the biodiesel in proportions of 40 ppm to 120 ppm using an ultrasonicator. The intact study is conducted in the diesel engine using the four fuel samples, namely diesel, PB20, INP50PB30, and INP75PB30, consecutively. The addition of nano-additive has resulted in higher brake thermal efficiency (BTE) by 3% and break-specific energy consumption (BSEC) by 3.3%, compared to diesel fuel. The emission levels of carbon monoxide (∼56%) and NOx (∼4%) are appreciably reduced with the addition of INP. Increase of INP in the blend from 50 ppm to 75 ppm, BTE and BSEC tend to reduce, but CO and NOx emissions are reduced.

scholarly journals Comparison between PEE10 and PEE10-Bioethanol Blends on Performance and Emission Characteristics of a HSDI Diesel Engine

2021 ◽  
Vol 18 (22) ◽  
pp. 451
Author(s):  
Ekkachai Sutheerasak ◽  
Charoen Chinwanitcharoen ◽  
Sathaporn Chuepeng
Keyword(s):  
Nitric Oxide ◽  
Carbon Dioxide ◽  
Diesel Engine ◽  
Palm Oil ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency

Biofuels are an alternative fuel currently being developed to reduce the diesel-engine environmental impact. The release of carbon dioxide (CO2), nitric oxide (NO) and black smoke (BS) becomes an issue derived from diesel engines even in lean-mixture combustion causing an adverse effect to human health. The main aim of the research study is to present the use of biofuels, a mixture of diesel and 10 % palm oil ethyl ester (PEE10) and PEE10 blended with bioethanol from 5 to 20 %, compared with conventional diesel fuel. The biofuels were run on a high-speed direct injection diesel engine at a constant speed of 3,000 rpm under various loads. The use of PEE10 resulted in brake thermal efficiency (BTE) reduction by 2 % and brake specific fuel consumption (BSFC) incrementation by 8 %, but the exhaust emissions were lower than diesel, except for CO2 and NO. However, PEE10 engine performance was better and exhaust gas emissions were lower for both pollutants than diesel mixed with 10 % bioethanol. The investigation of PEE10 with increasing bioethanol revealed that the use of PEE10 blended with 5 % bioethanol (PEE10E5) can improve engine performance, while the BTE and BSFC were close to that of diesel, and exhaust emissions, especially CO2, NO and BS reduced. Moreover, BTE from PEE10E5 fueling increased by 2 % but BSFC was subtle increased, compared to PEE10. On the other hand, the increasing bioethanol from 10 to 20 % in PEE10 led to the more reduction in engine performance, but the engine pollutants were also continuously decreased. Specifically, the blend of PEE10 and 20 % bioethanol indicates that CO2, NO and BS were reduced by 10, 15 and 33 %, respectively, compared to diesel fuel. HIGHLIGHTS A mixture of diesel and 10 % palm oil ethyl ester (PEE10) has less exhaust emissions than diesel blended with 10 % palm oil methyl ester (PME10) PEE10 blended with 5 % bioethanol can improve engine performance, while the brake thermal efficiency and brake specific fuel consumption are close to that of diesel and PME10 The increasing bioethanol from 10 to 20 % in PEE10 leads to the more reduction in engine performance, but the engine pollutants, especially carbon dioxide, nitric oxide and black smoke, are also continuously decreased GRAPHICAL ABSTRACT

Comparison of Bio-Fischer-Tropsch Fuel and Commercial Diesel Fuel Application in a 1600 CC Euro 5 Diesel Engine

2015 ◽  
Author(s):  
Claus Suldrup Nielsen ◽  
Jesper Schramm ◽  
Anders Ivarsson ◽  
Azhar Malik ◽  
Terese Løvås
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Steady State ◽  
Diesel Engine ◽  
Carbon Dioxide Emissions ◽  
Operating Conditions ◽  
Injection Timing ◽  
Nox Emissions ◽  
Fischer Tropsch ◽  
Operating Range

A direct injected and turbocharged Euro 5 diesel engine has been set up in a test bench where the vehicle driving conditions of the European NEDC (New European Driving Cycle) test can be simulated. The engine is operated as the engine of a corresponding vehicle, equipped with a similar engine and driving through the NEDC cycle. The regulated gaseous emissions, carbon monoxide, hydrocarbons and nitrogen oxides, as well as particulate numbers and size distributions where measured in 5 selected steady state operating points during the engine test. Fuel consumptions and carbon dioxide emissions where measured as well. The steady state operating conditions were chosen within the engine operating range during a vehicle NEDC test and representing as broad an operating range as possible during the NEDC test. A method is presented in which the NEDC test emissions are calculated from the 5 steady state measurements. It is shown that the method gives emission results that agree well with values that can be expected from the vehicle in question during an NEDC test. In this way a limited number of steady state measurements can be used to simulate vehicle emissions. The reason for carrying out engine experiments instead of vehicle measurements was to obtain well controlled engine conditions and thus better insight in the operation of the engine in the individual phases of operation, and thereby enable evaluation of the possibilities for improving engine performance with respect to emission and fuel consumption reduction. Two different fuels where tested. These were a Fischer-Tropsch fuel, produced from biomass at the Güssing gasification plant in Austria and a commercial diesel from a fuel station in Denmark. The results of the measurements and engine modification considerations showed that bio Fischer-Tropsch fuel does have advantages with respect to particulate and also small advantages with carbon monoxide and carbon dioxide emissions. However, NOx emissions are rather a question of the injection timing of the fuel, and the NOx emissions can be adjusted to give the same level of emissions by changing the injection timing with ordinary diesel. The injection strategy was changed in order to attempt to reduce NOx emissions below the limits in the Euro 6 regulations.

Performance Investigation of a Four Stroke Diesel Engine, Using Water-Based Ferrofluid as an Additive

2011 ◽  
Author(s):  
F. Daneshvar ◽  
N. Jahani ◽  
M. B. Shafii
Keyword(s):  
Experimental Study ◽  
Magnetic Nanoparticles ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Brake Specific Fuel Consumption ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Diesel Fuels ◽  
Water Based

In this experimental study, a four stroke diesel engine was conducted to investigate the effect of adding water-based ferrofluid to diesel fuel on engine performance. To our knowledge, Magnetic nanoparticles had not been used before. To this end, emulsified diesel fuels of 0, 0.4, and 0.8 water-based ferrofluid/Diesel ratios by volume were used as fuel. The ferrofluid used in this study was a handmade water-based ferrofluid prepared by the authors. The results show that adding water-based ferrofluid to diesel fuel has a perceptible effect on engine performance, increasing the brake thermal efficiency relatively up to 12%, and decreasing the brake specific fuel consumption relatively up to 11% as compared to diesel fuel. In addition, the results indicate that increasing ferrofluid concentration will magnify the results. Furthermore, it was found that magnetic nanoparticles can be collected at the engine exhaust using magnetic bar.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

S. I. Engine Pollution Control Using Low-Cost Palletized Catalytic Converter

Volume 2 ◽  
2004 ◽  
Author(s):  
Madhuri Jakkaraju ◽  
Vasudha Patri
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Pollution Control ◽  
Noble Metals ◽  
Fossil Fuel ◽  
Catalytic Converter ◽  
Low Cost ◽  
Hydrocarbon Emissions ◽  
Oxides Of Nitrogen ◽  
Carbon Dioxide Co2

I. C. Engines consume large amounts of fossil fuel emitting harmful pollutants like carbon monoxide (CO), unburnt hydrocarbons (UBHC), and oxides of nitrogen (NOx). By using a catalytic converter (CC), the carbon monoxide, hydrocarbon emissions can be transformed into less harmful carbon dioxide (CO2) & water vapor (H2O). Currently available CC’s are using costly noble metals like platinum (pt), palladium (pd), rhodium (rh) etc., hence making them expensive. This paper deals with the use of low-cost palletized silver coated alumina as the catalyst element in a CC. In this study, alumina and silver were used in the ratio of 10:1. All tests have been conducted on a stationary S.I. Engine at a constant speed of 1500 r.p.m with and without CC. Also, the performance of the palletized CC in combination with promoters like Bismuth, Cerium and Lanthanum was tested which have shown better results than silver alone as the coating element. It has been experimentally determined that the CO emissions have dropped from 7.25 (% vol) to 3.03(% vol) and the HC values have reduced from 350 ppm to 190 ppm.

Sign in / Sign up

Export Citation Format

Share Document