IPRP: Integrated Pyrolysis Combined Plant — An Efficient and Scalable Concept for Gas Turbine Based Energy Conversion From Biomass and Waste

2003 ◽  
Author(s):  
Francesco Fantozzi ◽  
Bruno D’Alessandro ◽  
Umberto Desideri
Keyword(s):  
Energy Conversion ◽  
Gas Turbine ◽  
Power Plants ◽  
Social Impact ◽  
High Efficiency ◽  
Energy Content ◽  
Waste To Energy ◽  
Fluidised Bed ◽  
Steam Power ◽  
Scale Range

A massive effort towards sustainability is necessary to prevent global warming and energy sources impoverishment: both biomass and waste to energy conversion may represent key actions to reach this goal. At the present State Of the Art (SOA) available technologies for biomass and waste to energy conversion are similar and include low to mid efficiency grate incineration or fluidised bed combustion with steam power cycles or mid to high efficiency Gas Turbine based cycles through integrated gasification technology. Nevertheless these plants are all available from mid-to-high scale range that can be highly intrusive on protected areas and socially unacceptable. This paper proposes an innovative, low cost, high efficiency plant in which the residue is gasified in absence of oxygen (pyrolysis), in a rotary kiln, by means of a highly regenerative gas turbine based cycle. Pyrolysis is preferred to gasification, because the syngas obtained has a higher LHV and produces char or tar as a by-product with an interesting energy content to be re-utilized inside the cycle. Different plant configurations are proposed and discussed through principal thermodynamic variables parametric analysis. Results show that very interesting efficiencies are obtainable in the 30%–40% range, at every scale range therefore presenting an interesting alternative especially to small size (below 5 MW) grate incineration and steam power plant technology. Moreover, the IPRP plant provides a unique solution for micro-scale (below 500 kW) power plants, opening a new and competitive possibility for distributed biomass or waste to energy conversion systems where low environmental and social impact turns into higher interest and positive dissemination effect.

Integrated Pyrolysis Regenerated Plant (IPRP): An Efficient and Scalable Concept for Gas Turbine Based Energy Conversion From Biomass and Waste

2005 ◽  
Vol 127 (2) ◽  
pp. 348-357 ◽  
Author(s):  
Francesco Fantozzi ◽  
Bruno D’Alessandro ◽  
Umberto Desideri
Keyword(s):  
Energy Conversion ◽  
Gas Turbine ◽  
Power Plants ◽  
Social Impact ◽  
High Efficiency ◽  
Energy Content ◽  
Low Cost ◽  
Waste To Energy ◽  
Fluidized Bed Combustion ◽  
Energy Conversion Systems

A massive effort towards sustainability is necessary to prevent global warming and energy sources impoverishment: both biomass and waste to energy conversion may represent key actions to reach this goal. At the present, state of the art available technologies for biomass and waste to energy conversion are similar and include low to mid efficiency grate incineration or fluidized bed combustion with steam power cycles or mid to high efficiency gas turbine based cycles through integrated gasification technology. Nevertheless, these plants are all available from mid-to-high scale range that can be highly intrusive on protected areas and socially unacceptable. This paper proposes an innovative, low cost, high efficiency plant in which the residue is gasified in the absence of oxygen (pyrolysis), in a rotary kiln, by means of a highly regenerative gas turbine based cycle. Pyrolysis is preferred to gasification, because the syngas obtained has a higher low heating value and produces char or tar as a by-product with an interesting energy content to be re-utilized inside the cycle. Different plant configurations are proposed and discussed through principal thermodynamic variables parametric analysis. Results show that very interesting efficiencies are obtainable in the 30–40% range for every plant scale. This fact shows how IPRP technology can provide an interesting alternative to traditional technologies, especially for the small size (below 5MW). Moreover, the IPRP technology provides a unique solution for microscale (below 500 kW) power plants, opening a new and competitive possibility for distributed biomass or waste to energy conversion systems where low environmental and social impact turns into higher interest and positive dissemination effect.

FEATURES OF THE METHODOLOGY OF THERMODYNAMIC MODELING OF GAS TURBINE AND COMBINED ON THEIR BASIS POWER PLANTS

2017 ◽  
Author(s):  
Gennadii Liubchik ◽  
◽  
Nataliia Fialko ◽  
Aboubakr Regragui ◽  
Julii Sherenkovskii ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Thermodynamic Analysis ◽  
Thermodynamic Modeling ◽  
Power Plants ◽  
High Efficiency ◽  
Technical Facility

The article presents the enthalpy-entropy methodology of thermodynamic analysis of gas turbine and combined power plants on their basis, the results of testing the method on a real technical facility, proving its high efficiency.

scholarly journals Thermodynamic Cycle Concepts for High-Efficiency Power Plans. Part A: Public Power Plants 60+

2019 ◽  
Vol 11 (2) ◽  
pp. 554 ◽  
Author(s):  
Krzysztof Kosowski ◽  
Karol Tucki ◽  
Marian Piwowarski ◽  
Robert Stępień ◽  
Olga Orynycz ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Carbon Dioxide Emissions ◽  
Power Plants ◽  
High Efficiency ◽  
Thermodynamic Cycle ◽  
Economic Resilience ◽  
Public Power ◽  
Pass System ◽  
Classical Gas ◽  
Gas Turbine Cycle

An analysis was carried out for different thermodynamic cycles of power plants with air turbines. Variants with regeneration and different cogeneration systems were considered. In the paper, we propose a new modification of a gas turbine cycle with the combustion chamber at the turbine outlet. A special air by-pass system of the combustor was applied and, in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with a regenerator can provide higher efficiency than a classical gas turbine cycle with a regenerator. The best arrangements of combined air–steam cycles achieved very high values for overall cycle efficiency—that is, higher than 60%. An increase in efficiency to such degree would decrease fuel consumption, contribute to the mitigation of carbon dioxide emissions, and strengthen the sustainability of the region served by the power plant. This increase in efficiency might also contribute to the economic resilience of the area.

scholarly journals Reheat and Regenerative Gas Turbines for Feed Water Repowering of Steam Power Plant

1995 ◽  
Author(s):  
G. Negri di Montenegro ◽  
M. Gambini ◽  
A. Peretto
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Flow Rate ◽  
Gas Turbines ◽  
Power Plants ◽  
Feed Water ◽  
Brayton Cycle ◽  
Energy Integration ◽  
Steam Power ◽  
Steam Power Plants

This study is concerned with the repowering of existing steam power plants (SPP) by gas turbine (GT) units. The energy integration between SPP and GT is analyzed taking into particular account the employment of simple and complex cycle gas turbines. With regard to this, three different gas turbine has been considered: simple Brayton cycle, regenerative cycle and reheat cycle. Each of these cycles has been considered for feed water repowering of three different existing steam power plants. Moreover, the energy integration between the above plants has been analyzed taking into account three different assumptions for the SPP off-design conditions. In particular it has been established to keep the nominal value for steam turbine power output or for steam flow-rate at the steam turbine inlet or, finally, for steam flow-rate in the condenser. The numerical analysis has been carried out by the employment of numerical models regarding SPP and GT, developed by the authors. These models have been here properly connected to evaluate the performance of the repowered plants. The results of the investigation have revealed the interest of considering the use of complex cycle gas turbines, especially reheat cycles, for the feed water repowering of steam power plants. It should be taken into account that these energy advantages are determined by a repowering solution, i.e. feed water repowering which, although it is attractive for its simplicity, do not generally allows, with Brayton cycle, a better exploitation of the energy system integration in comparison with other repowering solutions. Besides these energy considerations, an analysis on the effects induced by repowering in the working parameters of existing components is also explained.

Enhancing Gas Turbine Operation With Heavy Fuel Oil

2013 ◽  
Author(s):  
Vikram Muralidharan ◽  
Matthieu Vierling
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Power Plants ◽  
High Efficiency ◽  
Combined Cycle ◽  
Fuel Oil ◽  
Residual Oil ◽  
Heavy Fuel Oil ◽  
Hydro Power

Power generation in south Asia has witnessed a steep fall due to the shortage of natural gas supplies for power plants and poor water storage in reservoirs for low hydro power generation. Due to the current economic scenario, there is worldwide pressure to secure and make more gas and oil available to support global power needs. With constrained fuel sources and increasing environmental focus, the quest for higher efficiency would be imminent. Natural gas combined cycle plants operate at a very high efficiency, increasing the demand for gas. At the same time, countries may continue to look for alternate fuels such as coal and liquid fuels, including crude and residual oil, to increase energy stability and security. In over the past few decades, the technology for refining crude oil has gone through a significant transformation. With the advanced refining process, there are additional lighter distillates produced from crude that could significantly change the quality of residual oil used for producing heavy fuel. Using poor quality residual fuel in a gas turbine to generate power could have many challenges with regards to availability and efficiency of a gas turbine. The fuel needs to be treated prior to combustion and needs a frequent turbine cleaning to recover the lost performance due to fouling. This paper will discuss GE’s recently developed gas turbine features, including automatic water wash, smart cooldown and model based control (MBC) firing temperature control. These features could significantly increase availability and improve the average performance of heavy fuel oil (HFO). The duration of the gas turbine offline water wash sequence and the rate of output degradation due to fouling can be considerably reduced.

Performance and Economics of Advanced Energy Conversion Systems for Coal and Coal-Derived Fuels

1978 ◽  
Vol 100 (2) ◽  
pp. 252-259 ◽  
Author(s):  
J. C. Corman ◽  
G. R. Fox
Keyword(s):  
Energy Conversion ◽  
Power Plants ◽  
Technical Information ◽  
Steam Power ◽  
Energy Conversion Systems ◽  
Combined Cycles ◽  
Energy Conversion System ◽  
Open Cycle ◽  
Topping Cycle ◽  
Mhd System

The desire to establish an efficient Energy Conversion System to utilize the fossil fuel of the future—coal—has produced many candidate systems. A comparative technical/economic evaluation was performed on the seven most attractive advanced energy conversion systems. The evaluation maintains a cycle-to-cycle consistency in both performance and economic projections. The technical information base can be employed to make program decisions regarding the most attractive concept. A reference steam power plant was analyzed to the same detail and, under the same ground rules, was used as a comparison base. The power plants were all designed to utilize coal or coal-derived fuels and were targeted to meet an environmental standard. The systems evaluated were two advanced steam systems, a potassium topping cycle, a closed cycle helium system, two open cycle gas turbine combined cycles, and an open cycle MHD system.

Integrated Micro-Turbine and Rotary-Kiln Pyrolysis System as a Waste to Energy Solution for a Small Town in Central Italy: Cost Positioning and Global Warming Assessment

2002 ◽  
Author(s):  
Francesco Fantozzi ◽  
Francesco Di Maria ◽  
Umberto Desideri
Keyword(s):  
Global Warming ◽  
Power Plants ◽  
High Efficiency ◽  
Small Town ◽  
Central Italy ◽  
High Energy ◽  
Economic Feasibility ◽  
Cost Evaluation ◽  
Waste To Energy ◽  
Innovative Technology

Solid waste, and bio-residuals in general, are usually disposed of or alternatively converted into energy by means of medium to big scale power plants. For isolated communities, usually in protected natural areas, this turns into high energy and waste management costs because of their intrinsic distance from landfills and power plants. Considering also the electric dependency from the grid, small towns are commonly showing low sustainability. This paper focuses on both problems by evaluating the economic feasibility and the global warming contribution of an innovative micro scale waste to energy system based on a microturbine fuelled by waste pyrolysis gas. The plant reaches high efficiency, considering the scale, because of its high regenerative rate and is tailored to the waste disposal needs of Giano Dell’Umbria a small town in central Italy. The economic analysis was carried out, with the Net Present Value method, to determine the expected capital cost of the plant considering that the innovative technology utilized does not allow a reliable cost evaluation. The global warming contribution was calculated considering CO2 and CH4 avoided emission from landfilling and the better CO2 emission rate of such a technology with respect to the status quo. Results obtained show an acceptable cost positioning for the plant that makes it an interesting solution for distributed waste to energy systems. Executive projecting and construction of the proposed technology was funded and a pilot plant will be built and tested in 2002, in a laboratory facility of the University of Perugia.

scholarly journals Up-Rated Reheat Gas Turbine for the Repowering of Steam Power Plants

1999 ◽  
Author(s):  
G. Negri di Montenegro ◽  
A. Peretto ◽  
E. Mantino
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Fossil Fuel ◽  
Lower Cost ◽  
Combined Cycle ◽  
Internal Rate Of Return ◽  
Steam Power ◽  
Steam Power Plants ◽  
Combined Cycles ◽  
Fossil Fuel Power Plants

In the present paper, a thermoeconomic analysis of combined cycles derived from existing steam power plants is performed. The gas turbine employed is a reheat gas turbine. The increase of the two combustor outlet temperatures was also investigated. The study reveals that the transformation of old conventional fossil fuel power plants in combined cycle power plants with reheat gas turbine supplies a cost per kWh lower than that of a new combined cycle power plant, also equipped with reheat gas turbine. This occurs for all the repowered plants analyzed. Moreover, the solution of increasing the two combustor outlet temperatures resulted a strategy to pursue, leading, in particular, to a lower cost per kWh, Pay Back Period and to a greater Internal Rate of Return.

Thermoeconomic Analysis of Power Plants With Integrated Exergy Stream

2000 ◽  
Author(s):  
Duck-Jin Kim ◽  
Hyun-Soo Lee ◽  
Ho-Young Kwak ◽  
Jae-Ho Hong
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Plants ◽  
Unit Cost ◽  
Combined Cycle ◽  
Cogeneration Plant ◽  
Steam Power ◽  
Unit Costs ◽  
Combined Cycle Plant ◽  
The Cost

Abstract Exegetic and thermoeconomic analysis were performed for a 500-MW combined cycle plant and a 137-MW steam power plant without decomposition of exergy into thermal and mechanical exergy. A unit cost was assigned to a specific exergy stream of matter, regardless of its condition or state in this analysis. The calculated costs of electricity were almost same within 0.5% as those obtained by the thermoeconomic analysis with decomposition of the exergy stream for the combined cycle plant, which produces the same kind of product. Such outcome indicated that the level at which the cost balances are formulated does not affect the result of thermoeconomic analysis, that is somewhat contradictory to that concluded previously. However this is true for the gas-turbine cogeneration plant which produces different kinds of products, electricity and steam whose unit costs are dominantly affected by the mechanical and thermal exergy respectively.

Sign in / Sign up

Export Citation Format

Share Document