Effect of Dynamic Chemical Etching on the Pore Structure, Permeability, and Mechanical Properties of Ti-Nb-Zr Scaffolds for Medical Applications

2020 ◽  
Vol 143 (5) ◽  
Author(s):  
V. Sheremetyev ◽  
S. Dubinskiy ◽  
M. A. Iqbal ◽  
K. Lukashevich ◽  
S. Prokoshkin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Porous Structure ◽  
Chemical Etching ◽  
Etching Technique ◽  
Essential Step ◽  
Compressive Stresses ◽  
Structure Geometry ◽  
Structure Lead ◽  
New Generation ◽  
Potential Use

Abstract Improving the post-processing of metallic porous tissue scaffolds is an essential step to create a new generation of superelastic implants for the replacement of damaged bone tissue. In this study, the dynamic chemical etching technique is applied to improve the permeability and to optimize the porous structure of Ti-Nb-Zr scaffolds fabricated by the powder metallurgy-based space holder technique. The etched scaffolds are characterized in terms of their porous structure geometry, permeability, and mechanical properties. It is shown that an increase in porosity from 49% to 54% during the etching is mainly due to an increase in the number of 100 to 800 μm-diameter pores, from 30% to 50% of them measuring from 100 to 300 μm in size. These changes in the porous structure lead to a significant increase of its permeability, i.e., from (0.1–15) × 10−11 m2 before etching to (44–91) × 10−11 m2, after etching; these permeability ranges corresponding to those of bone tissues. Furthermore, the etched scaffolds show systematically higher yield compressive stresses as compared to the as-sintered scaffolds of equivalent porosities. Finally, the highly permeable etched Ti-Nb-Zr scaffolds with a porosity varying from 40% to 60% exhibit an apparent Young’s modulus ranging from 8.6 to 1.9 GPa and an ultimate compressive strength from 650 to 190 MPa, which can be considered as a promising balance of properties for the potential use of these scaffolds as bone implants.

The influence of chemical etching on porous structure and mechanical properties of the Ti6AL4V Functionally Graded Porous Scaffolds fabricated by EBM

2022 ◽  
Vol 275 ◽  
pp. 125217
Author(s):  
Maria A. Surmeneva ◽  
Dmitriy Khrapov ◽  
Konstantin Prosolov ◽  
Maria Kozadayeva ◽  
Andrey Koptyug ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Porous Structure ◽  
Chemical Etching ◽  
Functionally Graded ◽  
Porous Scaffolds

Effects of vacuum soaking on the hydration, steaming, and physiochemical properties of japonica rice

2021 ◽  
Vol 85 (3) ◽  
pp. 634-642
Author(s):  
Qiuyun Li ◽  
Sen Li ◽  
Xiao Guan ◽  
Kai Huang ◽  
Fengbo Zhu
Keyword(s):  
Porous Structure ◽  
Water Absorption ◽  
Microstructure Analysis ◽  
Japonica Rice ◽  
Starch Granules ◽  
Gelatinization Temperature ◽  
Relative Crystallinity ◽  
Physiochemical Properties ◽  
Essential Step ◽  
Density Of Water

ABSTRACT Soaking is an essential step in the processing of various rice products. In this study, the influences of vacuum soaking on hydration, steaming, and physiochemical properties of rice were investigated. Results showed that vacuum soaking accelerated water absorption as well as affected the mobility and density of water protons inside rice during soaking. Vacuum soaking could considerably shorten the optimal steaming time from 58 to 32 min and reduce the adhesiveness of steamed rice. Microstructure analysis of rice revealed that porous structure was formed on rice surface and the arrangement of starch granules became loosened after vacuum soaking. Moreover, vacuum soaking slightly reduced the relative crystallinity of rice starches without altering the crystalline type. The gelatinization temperature as well as the peak and trough viscosity was also decreased after vacuum soaking. Our study suggested that vacuum soaking was conducive to improve the soaking and steaming properties of rice.

scholarly journals Influence of a Natural Plant Antioxidant on the Ageing Process of Ethylene-norbornene Copolymer (Topas)

2021 ◽  
Vol 22 (8) ◽  
pp. 4018
Author(s):  
Anna Masek ◽  
Angelika Plota
Keyword(s):  
Mechanical Properties ◽  
Food Packaging ◽  
Colour Change ◽  
Good Alternative ◽  
Plant Origin ◽  
Aging Behavior ◽  
Current State ◽  
Ft Ir ◽  
Potential Use

In the field of polymer technology, a variety of mainly synthetic additives are used to stabilize the materials during processing. However, natural compounds of plant origin can be a green alternative to chemicals such as synthetic polyphenols. An analysis of the effect of hesperidin on the aging behavior of ethylene-norbornene copolymer was performed. The evaluation of changes in the tested samples was possible by applying the following tests: determination of the surface energy and OIT values, mechanical properties analysis, colour change measurements, FT-IR and TGA analyses. The obtained results proved that hesperidin can be effectively used as natural stabilizer for polymers. Furthermore, as a result of this compound addition to Topas-silica composites, their surface and physico-mechanical properties have been improved and the resistance to aging significantly increased. Additionally, hesperidin can act as a dye or colour indicator and only few scientific reports describe a possibility of using flavonoids to detect changes in products during their service life, e.g., in food packaging. In the available literature, there is no information about the potential use of hesperidin as a stabilizer for cycloolefin copolymers. Therefore, this approach may contribute not only to the current state of knowledge, but also presents an eco-friendly solution that can be a good alternative to synthetic stabilizers.

Controllable end shape modification of ZnO nano-arrays/rods by a simple wet chemical etching technique

2015 ◽  
Vol 48 (36) ◽  
pp. 365303 ◽  
Author(s):  
Jingchang Sun ◽  
Ting Zhao ◽  
Zhangwei Ma ◽  
Ming Li ◽  
Cheng Chang ◽  
...  
Keyword(s):  
Chemical Etching ◽  
Shape Modification ◽  
Etching Technique ◽  
Wet Chemical ◽  
Wet Chemical Etching

scholarly journals The Art of Tungsten Etching in Semiconductor Chips

1999 ◽  
Vol 7 (2) ◽  
pp. 24-25
Author(s):  
Lisa Litz-Montanaro
Keyword(s):  
Manufacturing Process ◽  
Chemical Etching ◽  
Layer By Layer ◽  
Ion Milling ◽  
Etching Technique ◽  
Semiconductor Structures ◽  
Wet Chemical ◽  
Wet Chemical Etching ◽  
Semiconductor Chips ◽  
Complex Semiconductor

In the course of both physical and failure analysis of semiconductor chips (i.e., verifying what you actually deposited as a layer, vs, what caused the circuit to fail), it is essential to have appropriate deprocessing tools at your disposal in order to evaluate complex semiconductor structures, Deprocessing techniques are developed for each product manufactured and involve multi-step procedures that reveal the layer-by-layer secrets of the chip, These techniques require constant tweaking in duration and procedure as the manufacturing process imposes changes and as the architecture of the semiconductor changes. While there are many tools that assist in these analytical pursuits, such as RIE (reactive ion etching - a dry etching technique), ion milling, and microcleaving, the wet chemical etching of tungsten is sometimes more reproducible than RIE techniques.

Defining the Mechanical Properties of a Spring-hinged Ankle Foot Orthosis to Assess its Potential Use in Children With Spastic Cerebral Palsy

2014 ◽  
Vol 30 (6) ◽  
pp. 728-731 ◽  
Author(s):  
Yvette L. Kerkum ◽  
Merel-Anne Brehm ◽  
Annemieke I. Buizer ◽  
Josien C. van den Noort ◽  
Jules G. Becher ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cerebral Palsy ◽  
Knee Flexion ◽  
Spastic Cerebral Palsy ◽  
Gait Performance ◽  
Ankle Foot Orthosis ◽  
The Moment ◽  
Potential Use ◽  
Foot Orthosis ◽  
Walking Energy Cost

A rigid ventral shelf ankle foot orthosis (AFO) may improve gait in children with spastic cerebral palsy (SCP) whose gait is characterized by excessive knee flexion in stance. However, these AFOs can also impede ankle range of motion (ROM) and thereby inhibit push-off power. A more spring-like AFO can enhance push-off and may potentially reduce walking energy cost. The recent development of an adjustable spring-hinged AFO now allows adjustment of AFO stiffness, enabling tuning toward optimal gait performance. This study aims to quantify the mechanical properties of this spring-hinged AFO for each of its springs and settings. Using an AFO stiffness tester, two AFO hinges and their accompanying springs were measured. The springs showed a stiffness range of 0.01−1.82 N·m·deg−1. The moment-threshold increased with increasing stiffness (1.13–12.1 N·m), while ROM decreased (4.91–16.5°). Energy was returned by all springs (11.5–116.3 J). These results suggest that the two stiffest available springs should improve joint kinematics and enhance push-off in children with SCP walking with excessive knee flexion.

Use of Sugarcane Bagasse Ashes as Raw Material in the Replacement of Fluxes for Applications on Porcelain Tile

2016 ◽  
Vol 881 ◽  
pp. 383-386 ◽  
Author(s):  
Raimundo J.S. Paranhos ◽  
Wilson Acchar ◽  
Vamberto Monteiro Silva
Keyword(s):  
Mechanical Properties ◽  
Environmental Impact ◽  
Physical Properties ◽  
Sugarcane Bagasse ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Raw Material ◽  
The Cost ◽  
Potential Use ◽  
Porcelain Tile

This study evaluated the potential use of Sugarcane Bagasse Ashes (SBA) as a flux, replacing phyllite for the production of enamelled porcelain tile. The raw materials of the standard mass components and the SBA residue were characterized by testing by XRF, XRD, AG, DTA and TGA. Test samples were fabricated, assembled in lots of 3 units and sintered at temperatures of 1150 ° C to 1210 ° C. The results of the physical properties, mechanical properties and SEM of the sintered samples, showed that the formulation, G4 - in which applied 10% of SBA replacing phyllite, sintering temperature 1210 ° C showed better performance as the previously mentioned properties due to the formation of mullite crystals, meeting the prerequisites of standards for enamelled porcelain tile, while reducing the environmental impact and the cost of production.

scholarly journals The potential use of lightweight cellular concrete in pavement application: a review

2020 ◽  
Vol 13 (6) ◽  
pp. 686-696
Author(s):  
Frank Mi-Way Ni ◽  
Abimbola Grace Oyeyi ◽  
Susan Tighe
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ease Of Use ◽  
Potential Candidate ◽  
Actual Performance ◽  
Freeze Thaw ◽  
Lower Weight ◽  
And Performance ◽  
Potential Use ◽  
Cellular Concrete

AbstractProtecting the pavement subgrade to increase the service life of road pavements is an aspect currently being explored. Several alternative pavement subbase materials are being considered, including Lightweight Cellular Concrete (LCC). Due to its lower weight, LCC incorporating industrial by-product, making it sustainable, and ease of use amongst other benefits, is seen as a potential candidate. This paper reports reviewing the potential application of LCC within the pavement structure with a specific application as a subbase. It examines the various properties such as modulus of elasticity, compressive and tensile strength, Water absorption, and freeze-thaw resistance necessary for pavement application. It also assesses its use in the field in Canada considering the design methods utilized. Some limitations and gaps for LCC application in pavements are also established and recommendations on how to further its use and performance. This review concludes that LCC possesses potential as a pavement subbase alternative; however, other mechanical properties like LCC’s fatigue life is essential. A comparative field study is also recommended to monitor actual performance and various factors on performance.

Anti-obesity Medications in Cancer Therapy: A Comprehensive Insight

2021 ◽  
Vol 21 ◽  
Author(s):  
Rajveer Singh Shekhawat ◽  
Chandi C Mandal
Keyword(s):  
Cross Talk ◽  
Neoplastic Transformation ◽  
Cancer Growth ◽  
Chemotherapeutic Drug ◽  
Essential Step ◽  
Cellular Events ◽  
Oncogenic Pathways ◽  
Increased Risk ◽  
Risk Of Cancer ◽  
Potential Use

: The interplay between cancer and obesity is multifactorial and complex with the increased risk of cancer development in obese individuals posing a significant threat. Obesity leads to the upregulation or hyperactivation of several oncogenic pathways in cancer cells, which drives them towards a deleterious phenotype. The cross-talk between cancer and obesity is considered a large contributing factor in the development of chemotherapeutic drug resistance and the resistance to radiotherapy. The link between obesity and the development of cancer is so strong that a medication that demonstrates effectiveness against both conditions would serve as an essential step. In this context, anti-obesity medications provide a worthy list of candidates based on their chemo-preventive potential and chemotherapeutic properties. The current study focuses on exploring the potential of anti-obesity medicines as dual anticancer drugs. These medications target several key signaling pathways (e.g., AMPK, PI3K/Akt/mTOR, MAPK, NF-κB, JNK/ERK), which prove to be crucial for both cancer growth and metastases. Some of these drugs also play an important role in attenuating the signaling and cellular events which incite cancer-obesity cross-talk and demonstrate efficient counteraction of neoplastic transformation. Thus, this review highlights a comprehensive view of the potential use of anti-obesity medicines to treat both cancer and obesity for patients exhibiting both comorbities.

Performance of Wood-Polymer Composite Prepared by In Situ Synthesis of Terpolymer within Wood

2010 ◽  
Vol 34-35 ◽  
pp. 1165-1169 ◽  
Author(s):  
Yong Feng Li ◽  
Bao Gang Wang ◽  
Qi Liang Fu ◽  
Yi Xing Liu ◽  
Xiao Ying Dong
Keyword(s):  
Mechanical Properties ◽  
Porous Structure ◽  
Polymer Composite ◽  
Value Added ◽  
Untreated Wood ◽  
Modulus Of Rupture ◽  
Hydroxyl Group ◽  
Wood Polymer ◽  
Wood Polymer Composite

In order to improve the value-added applications of low-quality wood, a novel composite, wood-polymer composite, was fabricated by in-situ terpolymerization of MMA, VAc and St within wood porous structure. The structure of the composite and the reaction of monomers within wood were both analyzed by SEM and FTIR, and the mechanical properties were also evaluated. The SEM observation showed that the polymer mainly filled up wood pores, suggesting good polymerizating crafts. The FTIR results indicated that under the employed crafts, three monomers terpolymerized in wood porous structure, and grafted onto wood matrix through reaction of ester group from monomers and hydroxyl group from wood components, suggesting chemical combination between the two phases. The mechanical properties of the wood-polymer composite involving modulus of rupture, compressive strength, wearability and hardness were improved 69%, 68%, 36% and 210% over those of untreated wood, respectively. Such method seems to be an effective way to converting low-quality wood to high-quality wood.

Sign in / Sign up

Export Citation Format

Share Document