High Dimensional Matching Optimization of Impeller–Vaned Diffuser Interaction for a Centrifugal Compressor Stage

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Ruihong Qin ◽  
Yaping Ju ◽  
Lee Galloway ◽  
Stephen Spence ◽  
Chuhua Zhang
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Sequential Optimization ◽  
High Dimensional ◽  
Compressor Stage ◽  
Optimization Strategy ◽  
Impeller Blade ◽  
Vaned Diffuser ◽  
Flow Angle

Abstract The matching and interaction between the impeller and vaned diffuser is the most important aerodynamic-coupling between the components of a high-speed centrifugal compressor. Many research studies have been carried out during the last decade, both experimentally and numerically, on the flow mechanisms underlying impeller–vaned diffuser matching and interaction, with the aim of achieving a high-performance stage. However, the published work lacks any study that optimizes the matching of the impeller–vaned diffuser components in the environment of a full compressor stage due to two unresolved issues, i.e., identifying an effective matching optimization strategy and the high dimensional nature of the problem. To tackle these difficulties, four different optimization strategies (i.e., (1) integrated, (2) single component, (3) parallel, and (4) sequential optimization strategies) have been proposed and validated through a high dimensional matching optimization of the Radiver compressor test case published by the Institute of Jet Propulsion and Turbomachinery at Rheinisch-Westfälische Technische Hochschule (RWTH) Aachen University. Particular attention has been paid to the slope of the diffuser total pressure ratio characteristic near the surge point to further extend the stage surge margin. The results showed that the integrated optimization strategy was the most effective one for achieving good matching of the impeller–vaned diffuser interaction due to its inherently strong coupling optimization. Compared with the baseline compressor, the optimized stage achieved a gain of 1.2% in total-to-total isentropic efficiency at the peak efficiency point as well as a predicted 26.17% increase in stable operating range. For the stage examined in this study, a fore-loaded design of impeller blade as well as an increased vane angle for the diffuser vane was beneficial to the impeller–vaned diffuser matching. The more uniform spanwise distributions of the impeller discharge flow angle and the diffuser vane incidence presented the opportunity for a more optimized matching of the flow field between the 3D impeller and the 2D vaned diffuser. The outcomes of this work are particularly relevant for the advanced design of high-speed centrifugal compressors.

Some Studies on Low Solidity Vaned Diffusers of a Centrifugal Compressor Stage

2005 ◽  
Author(s):  
T. Ch. Siva Reddy ◽  
G. V. Ramana Murty ◽  
Prasad Mukkavilli ◽  
D. N. Reddy
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Pressure Recovery ◽  
Compressor Stage ◽  
Recovery Coefficient ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Centrifugal Compressor Stage ◽  
Pressure Recovery Coefficient

Numerical simulation of impeller and low solidity vaned diffuser (LSD) of a centrifugal compressor stage is performed individually using CFX- BladeGen and BladeGenPlus codes. The tip mach number for the chosen study was 0.35. The same configuration was used for experimental investigation for a comparative study. The LSD vane is formed using standard NACA profile with marginal modification at trailing edge. The performance parameters obtained form numerical studies at the exit of impeller and the diffuser have been compared with the corresponding experimental data. These parameters are pressure ratio, polytropic efficiency and flow angle at the impeller exit where as the parameters those have been compared at the exit of diffuser are the static pressure recovery coefficient and the exit flow angle. In addition, the numerical prediction of the blade loading in terms of blade surface pressure distribution on LSD vane has been compared with the corresponding experimental results. Static pressure recovery coefficient and flow angle at diffuser exit is seen to match closely at higher flows. The difference at lower flows could be due to the effect of interaction between impeller and diffuser combinations, as the numerical analysis was done separately for impeller and diffuser and the effect of impeller diffuser interaction was not considered.

scholarly journals Flow Studies in a Centrifugal Compressor Stage

2014 ◽  
Author(s):  
R. Rajendran
Keyword(s):  
Centrifugal Compressor ◽  
Flow Behavior ◽  
Compressor Stage ◽  
Impeller Blade ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Impeller Outlet ◽  
Outlet Flow

The overall efficiency of a compressor is dependent on the design of both the impeller and the diffuser. The vaned diffuser reduces the operating range compared to the vaneless diffuser. However, by proper setting of the diffuser with reference to the impeller, it is possible to achieve a good stage performance. This paper describes the experimental investigation of the detailed flow behavior inside a centrifugal compressor stage for three different setting angles of the vaned diffuser with reference to the fixed impeller blade outlet angle. It is seen that diffuser setting angles lower than the impeller outlet flow angle gives wide operating range.

Study on Aerodynamic Redesign of a High Pressure Ratio Centrifugal Compressor

2010 ◽  
Author(s):  
Chaolei Zhang ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Centrifugal Compressor ◽  
Cfd Simulation ◽  
Pressure Ratio ◽  
Aerodynamic Performance ◽  
Compressor Stage ◽  
Operation Condition ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Optimum Configuration ◽  
Operation Conditions

This paper describes the aerodynamic redesign and optimization of a typical single stage centrifugal compressor, in which the total pressure ratio was improved from the original 4.0 to final 5.0 with the restrictions of keeping the impeller tip diameter, the design rotational speed and the design mass flow rate unchanged. Firstly the backsweep angle and the outlet blade height of the impeller were adjusted and the vaned diffuser was redesigned. Then a sensitivity analysis of the aerodynamic performance correlated to the primary redesign centrifugal compressor stage with respect to the chosen redesign variables was conducted, according to the parameterized results of the impeller and the vaned diffuser. Secondly the impeller and the vaned diffuser were optimized respectively under the stage environment at the design operation condition to improve the stage isentropic efficiency by using a global optimization method which coupled Evolutionary Algorithm (EA) and Artificial Neural Network (ANN), provided by the commercial software NUMECA DESIGN-3D. Subsequently the detailed performance maps of the centrifugal compressor stage corresponding to the primary redesign configuration and the optimum configuration were presented by Computational Fluid Dynamics (CFD) simulation. Finally the flow fields correlated to the centrifugal compressor configurations before and after optimization at the design operation condition were also compared and analyzed in detail. As a result the design target was achieved after the primary redesign, as a 2.7% gain in stage efficiency and a 3.6% increase in stage pressure ratio were obtained when compared with the primary redesign configuration after optimization. Moreover, the aerodynamic performance of the optimum configuration at the off-design operation conditions was also improved.

Multi-Blade Row Interactions in a Low Pressure Ratio Centrifugal Compressor Stage With a Vaned Diffuser

2011 ◽  
Author(s):  
Kishore Ramakrishnan ◽  
Simon K. Richards ◽  
Franc¸ois Moyroud ◽  
Vittorio Michelassi
Keyword(s):  
Centrifugal Compressor ◽  
Oil And Gas ◽  
Pressure Ratio ◽  
Compressor Stage ◽  
Vaneless Diffuser ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Acoustic Interaction ◽  
Field Excitation

Previous experimental and CFD investigation of a GE Oil and Gas centrifugal compressor stage with a vaneless diffuser revealed a complex excitation mechanism caused by an aero-acoustic interaction between three blade rows. In stages with vaned diffusers, additional sources of aeromechanical excitation on the impeller can be expected. This unsteady CFD investigation is a follow-up from the previous vaneless diffuser study to identify any additional sources of excitation that arise in the presence of a vaned diffuser in preparation for aeromechanic tests to be conducted later. The study confirms that excitation from impeller-diffuser interaction generated acoustic modes can dominate the potential field excitation from the diffuser vanes. In addition, a significant aero-acoustic excitation to the impeller at a vane pass frequency corresponding to the sum of the vane counts in the two downstream vane rows is observed, and its origination is discussed. The latter excitation is different from that observed in the vaneless diffuser stage where the vane pass frequency observed by the impeller corresponds to the sum of the vane counts in the upstream and downstream vane rows.

Effect of Unsteadiness on the Performance of a Transonic Centrifugal Compressor Stage

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Isabelle Trébinjac ◽  
Pascale Kulisa ◽  
Nicolas Bulot ◽  
Nicolas Rochuon
Keyword(s):  
Shock Wave ◽  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Wake Flow ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

Numerical and experimental investigations were conducted in a transonic centrifugal compressor stage composed of a backswept splittered unshrouded impeller and a vaned diffuser. The characteristic curves of the compressor stage resulting from the unsteady simulations and the experiments show a good agreement over the whole operating range. On the contrary, the total pressure ratio resulting from the steady simulations is clearly overestimated. A detailed analysis of the flow field at design operating point led to identify the physical mechanisms involved in the blade row interaction that underlie the observed shift in performance. Attention was focused on the deformation in shape of the vane bow shock wave due its interaction with the jet and wake flow structure emerging from the impeller. An analytical model is proposed to quantify the time-averaged effects of the associated entropy increase. The model is based on the calculation of the losses across a shock wave at various inlet Mach numbers corresponding to the moving of the jet and wake flow in front of the shock wave. The model was applied to the compressor stage performance calculated with the steady simulations. The resulting curve of the overall pressure ratio as a function of the mass flow is clearly shifted toward the unsteady results. The model, in particular, enhances the prediction of the choked mass flow.

Experimental Study of Pinch in Vaneless Diffuser of Centrifugal Compressor

2009 ◽  
Author(s):  
Teemu Turunen-Saaresti ◽  
Aki-Pekka Gro¨nman ◽  
Ahti Jaatinen
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Compressor Stage ◽  
Vaneless Diffuser ◽  
Moderate Amount ◽  
Flow Angle ◽  
Isentropic Efficiency

A centrifugal compressor is often equipped with a vaneless diffuser because the operation range of a vaneless diffuser is wider than the operation range of vaned diffuser, and the geometry of the vaneless diffuser is simple and inexpensive. The flow field after the centrifugal compressor rotor is highly complicated and the velocity is high. A moderate amount of this velocity should be recovered to the static pressure. It is important to study the flow field in the vaneless diffuser in order to achieve guidelines for design and an optimal performance. In this article, the experimental study of the pinch in the vaneless diffuser is conducted. Five different diffuser heights were used, b/b2 = 1, b/b2 = 0.903, b/b2 = 0.854, b/b2 = 0.806 and b/b2 = 0.903 (shroud). In three of the cases, the pinch was made to both walls of the diffuser, hub and shroud, and in one case, the pinch was made to the shroud wall. The total and the static pressure, the total temperature and the flow angle were measured at the diffuser inlet and outlet by using a cobra-probe, kiel-probes and flush-mounted pressure taps. In addition, the static pressure in the diffuser was measured at three different radius ratios. The overall performance, the mass flow, the pressure ratio and the isentropic efficiency of the compressor stage were also monitored. Detailed flow field measurements were carried out at the design rotational speed and at the three different mass flows (close to the surge, design and close to the choke). The isentropic efficiency and the pressure ratio of the compressor stage was increased with the pinched diffuser. The efficiency of the rotor and the diffuser was increased, whereas the efficiency of the volute/exit cone was decreased. The pinch made to the shroud wall was the most effective. The pinch made the flow angle more radial and increased the velocity at the shroud where the secondary flow (passage wake) from the rotor is present.

The Analysis of Aerodynamic Load for High Speed Centrifugal Compressor Blade

2013 ◽  
Vol 675 ◽  
pp. 103-106
Author(s):  
Gui Hua Zhu ◽  
Tuan Hui Qiu ◽  
Min Xie
Keyword(s):  
Flow Rate ◽  
Centrifugal Compressor ◽  
High Speed ◽  
Fluid Model ◽  
Pressure Ratio ◽  
Design Flow ◽  
Aerodynamic Load ◽  
Impeller Blade ◽  
Rate Condition ◽  
Rotating Speed

With the ANSYS Workbench software,the 3D fluid model of the impeller for the centrifugal compressor is set up,whose design flow is 3.2kg/s,rotating speed is 32473r/min,pressure ratio is 3.8,and then with the method of CFD,the k-ε two equations model is selected as the turbulence model,in the condition of design speed,the fluid region of the impeller is simulated under eight different flow rate,the aerodynamic load of the impeller blade and its distribution is acquired under different flow rate,the results showed that the location of the largest aerodynamic load is in the blade that near the outlet of impeller,under the design flow rate condition,the largest aerodynamic load is 0.1969MPa,the aerodynamic load increases with the flow rate decreases.

Spike and Modal Stall Inception in an Advanced Turbocharger Centrifugal Compressor

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Z. S. Spakovszky ◽  
C. H. Roduner
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Compression System ◽  
The Impact ◽  
Highly Loaded

In turbocharger applications, bleed air near the impeller exit is often used for secondary flow systems to seal bearing compartments and to balance the thrust load on the bearings. There is experimental evidence that the performance and operability of highly-loaded centrifugal compressor designs can be sensitive to the amount of bleed air. To investigate the underlying mechanisms and to assess the impact of bleed air on the compressor dynamic behavior, a research program was carried out on a preproduction, 5.0 pressure ratio, high-speed centrifugal compressor stage of advanced design. The investigations showed that bleed air can significantly reduce the stable flow range. Compressor rig experiments, using an array of unsteady pressure sensors and a bleed valve to simulate a typical turbocharger environment, suggest that the path into compression system instability is altered by the bleed flow. Without the bleed flow, the prestall behavior is dominated by short-wavelength disturbances, or so called “spikes,” in the vaneless space between the impeller and the vaned diffuser. Introducing bleed flow at the impeller exit reduces endwall blockage in the vaneless space and destabilizes the highly-loaded vaned diffuser. The impact is a 50% reduction in stable operating range. The altered diffuser characteristic reduces the compression system damping responsible for long-wavelength modal prestall behavior. A four-lobed backward traveling rotating stall wave is experimentally measured in agreement with calculations obtained from a previously developed dynamic compressor model. In addition, a self-contained endwall blockage control strategy was employed, successfully recovering 75% of the loss in surge-margin due to the bleed flow and yielding a one point increase in adiabatic compressor efficiency.

Effect of Unsteadiness on the Performance of a Transonic Centrifugal Compressor Stage

2008 ◽  
Author(s):  
Isabelle Tre´binjac ◽  
Pascale Kulisa ◽  
Nicolas Bulot ◽  
Nicolas Rochuon
Keyword(s):  
Shock Wave ◽  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Wake Flow ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

Numerical and experimental investigations were conducted in a transonic centrifugal compressor stage composed of a backswept splittered unshrouded impeller and a vaned diffuser. The characteristic curves of the compressor stage resulting from the unsteady simulations and the experiments show a good agreement over the whole operating range. On the contrary, the total pressure ratio resulting from the steady simulations is clearly overestimated. A detailed analysis of the flow field at design operating point led to identify the physical mechanisms involved in the blade row interaction that underlie the observed shift in performance. Attention was focused on the deformation in shape of the vane bow shock wave due its interaction with the jet and wake flow structure emerging from the impeller. An analytical model is proposed to quantify the time-averaged effects of the associated entropy increase. The model is based on the calculation of the losses across a shock wave at various inlet Mach numbers corresponding to the moving of the jet and wake flow in front of the shock wave. The model was applied to the compressor stage performance calculated with the steady simulations. The resulting curve of the overall pressure ratio as a function of the mass flow is clearly shifted towards the unsteady results. The model in particular enhances the prediction of the choked mass flow.

Numerical study on the Effect of Interaction Vaned Diffuser with Impeller on the Performance of a Modified Centrifugal Compressor

2013 ◽  
Vol 30 (2) ◽  
pp. 113-121 ◽  
Author(s):  
L. H. Jawad ◽  
S. Abdullah ◽  
R. Zulkifli ◽  
W. M. F. W. Mahmood
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Internal Flow ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Compressor Impeller ◽  
Inlet Conditions

ABSTRACTThis paper is a numerical simulation that was made in the three-dimensional flow, carried out in a modified centrifugal compressor, having vaned diffuser stage, used as an auto-motive turbo charger. Moreover, the performance of the centrifugal compressor was dependent on the proper matching between compressor impeller and vaned diffuser, influencing significantly surge and the efficiency of centrifugal compressor stages. In addition, a modified compressor impeller, coupled with vane and vaneless diffuser, has been found to have similar internal flow patterns for both the vaneless and vaned diffuser design. The vaned diffuser effect has been paid particular attention in terms of better analysis where the diffuser was designed for high sub-sonic inlet conditions. Another aim of this research was to study and simulate the effect of vaned diffuser on the performance of a centrifugal compressor. The simulation was undertaken by using a commercial software, the so-called ANSYS CFX, to predict numerically the performance in terms of pressure ratio, poly tropic efficiency and mass flow rate for the centrifugal compressor stage. The results were generated from CFD and were analyzed for better understanding of the fluid flow through centrifugal compressor stage. Conclusively, it was observed that the effect of the vaned diffuser is to convert the kinetic energy into a high static pressure after analyzing the results of the simulation.

Sign in / Sign up

Export Citation Format

Share Document