Low-Constraint Toughness Testing of Two Single-Edge Notched Tension Methods in a Single Specimen

2016 ◽  
Vol 138 (5) ◽  
Author(s):  
Dong-Yeob Park ◽  
Jean-Philippe Gravel ◽  
C. Hari Manoj Simha ◽  
Jie Liang ◽  
Da-Ming Duan
Keyword(s):  
Fracture Toughness ◽  
Crack Tip ◽  
Size Estimation ◽  
Single Specimen ◽  
Single Edge ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Line Pipe ◽  
Toughness Testing ◽  
Low Constraint

Single-edge notched tension (SE(T) or SENT) specimens have been increasingly proposed as a low-constraint toughness test to measure toughness of line pipe materials, as the crack tip constraint approximates a circumferential surface flaw in a pipe under loading. The clamped SE(T) single-specimen procedures recently developed by Shen and Tyson (2008, “Fracture Toughness Evaluation of High Strength Steel Pipe,” ASME Paper No. PVP2008-61100; 2008, “Development of Procedure for Low-Constraint Toughness Testing Using a Single-Specimen Technique,” CANMET Materials Technology Laboratory, Technical Report No. 2008-18 (TR)) and Tang et al. (2010, “Development of the SENT Test of Strain-Based Design of Welded Pipelines,” 8th International Pipeline Conference, IPC 2010, Calgary, AB, Canada) have both used in common the use of a clamped single-specimen of similar geometry and relied on the unloading compliance technique for crack size estimation. In the former case, a single clip gauge is attached to the integral knife edge and the crack-tip opening displacement (CTOD) is estimated by means of a J-integral-to-CTOD conversion, similar to the procedure of ASTM E1820-11. The latter uses a pair of clip gauges mounted on an attachable raised set of knife edges to estimate CTOD at the original crack tip position by a triangulation rule. Consolidating these two sets of clip gauges in a specimen makes direct comparisons of two SE(T) methods under identical test conditions: material, specimen geometry, equipment, test temperature, and operator (Weeks et al., 2013, “Fracture Toughness Instrumentation Techniques for Single-Specimen Clamped SE(T) Tests on X100 Linepipe Steel: Experimental Setup,” 6th Pipeline Technology Conference, Ostend, Belgium). In this study, SE(T) testing employing these two SE(T) methods on a single specimen was conducted on B × B shallow-cracked (a/W ∼ 0.35) specimens of two X70 pipeline girth welds. This paper discusses details of the two SE(T) methods and techniques on the same specimen.

Low-Constraint Toughness Testing of Two SE(T) Methods in a Single Specimen

2014 ◽  
Author(s):  
Dong-Yeob Park ◽  
Jean-Philippe Gravel ◽  
C. Hari Manoj Simha ◽  
Jie Liang ◽  
Da-Ming Duan
Keyword(s):  
Crack Tip ◽  
Crack Size ◽  
Size Estimation ◽  
Single Specimen ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Line Pipe ◽  
Low Constraint ◽  
Girth Welds ◽  
Crack Tip Constraint

Single-edge notched tension (SE(T) or SENT) specimens has been increasingly proposed as a low-constraint toughness test to measure toughness of line pipe materials, as the crack tip constraint approximates a circumferential surface flaw in a pipe under loading. The clamped SE(T) single-specimen procedures recently developed by Shen and Tyson [1, 2] and Tang et al. [3] have in common the use of a clamped single-specimen of similar geometry and rely on unloading compliance technique for crack size estimation. In the former case, a single clip gauge is attached to the integral knife edge and the crack-tip opening displacement (CTOD) is estimated by means of a J-integral-to-CTOD conversion, similar to the procedure of ASTM E1820. The latter uses a pair of clip gauges mounted to an attachable raised set of knife edges to estimate CTOD at the original crack tip position by a triangulation rule. Consolidating these two sets of clip gauges in a specimen makes direct comparisons of two SE(T) methods on identical test conditions: material, specimen geometry, equipment, test temperature and operator [4]. In this study, SE(T) testing employing these two SE(T) methods on a single specimen was conducted on BxB shallow-cracked (a/W∼0.35) specimens of two x70 pipeline girth welds. This paper discusses the details of two SE(T) methods and techniques on the same specimen.

Fracture Toughness of X70 Pipe Girth Welds Using Clamped SE(T) and SE(B) Single-Specimens

2014 ◽  
Author(s):  
Dong-Yeob Park ◽  
Jean-Philippe Gravel ◽  
C. Hari Manoj Simha ◽  
Jie Liang ◽  
Da-Ming Duan
Keyword(s):  
Fracture Toughness ◽  
Heat Affected Zone ◽  
Peak Load ◽  
Single Specimen ◽  
Single Edge ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Resistance Curves ◽  
Girth Welds ◽  
Crack Tip Opening

Shallow-notched single edge-notched tension (SE(T) or SENT) and deep- and shallow-notched single edge-notched bend (SE(B) or SENB) specimens with notches positioned in the weld and the heat-affected zone were tested. Crack-tip opening displacement (CTOD) versus resistance curves were obtained using both a single and double clip gauge consolidated in a SE(T) single-specimen. Up until the peak load the resistance curves from both gauging methods yield approximately the same results; thereafter the curves deviate. Interrupted testing showed that the crack had initiated below 50% of the peak load, and in some cases had propagated significantly prior to reaching the peak load.

Review of Low-Constraint Fracture Resistance Testing With SENT Specimens

2014 ◽  
Author(s):  
Xian-Kui Zhu ◽  
Tom McGaughy ◽  
Fabian Orth ◽  
Jon Jennings
Keyword(s):  
Fracture Resistance ◽  
Crack Tip ◽  
Test Methods ◽  
Resistance Testing ◽  
Resistance Curve ◽  
Single Specimen ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Resistance Curves ◽  
Low Constraint

Fracture resistance is an important material property and characterized by a J-integral resistance curve (J-R curve) or a crack-tip opening displacement (CTOD) resistance curve. ASTM standard specimens with deep cracks are subject to bending dominant forces, leading to high crack-tip constraint conditions and conservative fracture resistance curves. Actual cracks occurring in line pipes and welds are often shallow ones dominated by tensile forces, resulting in low constraint conditions. Shallow cracks have been shown to generate elevated fracture resistance curves in comparison to standard deep-crack results. To reduce the over-conservatism of standard resistance curves and to produce more realistic toughness properties to meet the needs of strain-based design approaches for pipelines, different procedures and technologies have been developed over the years to determine the low-constraint fracture resistance curves by use of the single edge-notched tension (SENT) specimens. This includes the multiple specimen method developed and standardized by DNV for J-R curve testing, the single specimen method developed by CanMet for J-R and CTOD-R curve testing, and the single-specimen method developed by ExxonMobil for CTOD-R curve testing. This paper delivers a technical review of existing fracture test methods using SENT specimens, and discusses the advantages and limitations of each method.

Why Conduct SEN(T) Tests and Considerations in Conducting/Analyzing SEN(T) Testing

2010 ◽  
Author(s):  
S. Kalyanam ◽  
G. M. Wilkowski ◽  
D.-J. Shim ◽  
F. W. Brust ◽  
Y. Hioe ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Crack Growth ◽  
Traditional Approach ◽  
Crack Tip ◽  
Maximum Load ◽  
Single Edge ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Growing Crack ◽  
Crack Tip Opening

This paper outlines a methodology used to conduct a SEN(T) fracture test and discusses the analysis procedure used to obtain J-R and CTOD-R resistance curves from the experimental data. The CTOD-R curve depicts the change in toughness with crack growth, in a manner similar to the J-R curve methodology. Significant crack growth can arise from the start of ductile tearing to maximum load in the case of surface-cracked pipes with heavier-wall piping used in recent designs of natural gas pipelines that are required to handle greater pressures and much lower temperatures. CTOD-R curves provide toughness values that are a factor of 2 to 3 times higher at maximum load when compared to the toughness at crack initiation. The impacts of this on stress and strain-based design of pipelines are highlighted. Further, the differences between the traditional approach that uses the crack-tip-opening-displacement at the initial crack tip (CTOD′) versus the more recent developments that employ the crack-tip-opening-displacement at the growing crack tip (CTOD) are examined. The CTOD-R curve for the growing crack tip is more consistent with J-R curve analyses. Single-edge-notched bend [SEN(B)] or popularly called bend-bar specimens are used for crack-tip-opening-displacement (CTOD) as well as J-integral toughness testing. This paper discusses the advantages of using the fracture toughness data determined from a single-edge-notched tension [SEN(T)] specimen from considerations of the constraints faced by surface cracks in pipelines and the differences in fracture toughness values seen between the SEN(T) and SEN(B) specimens in the transition temperature region.

scholarly journals Modelling of Fracture Toughness of X80 Pipeline Steels in DTB Transition Region Involving the Effect of Temperature and Crack Growth

Metals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 28
Author(s):  
Jie Xu ◽  
Wei Song ◽  
Wenfeng Cheng ◽  
Lingyu Chu ◽  
Hanlin Gao ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Crack Growth ◽  
Three Dimensional ◽  
Crack Tip ◽  
Effect Of Temperature ◽  
Single Edge ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Pipeline Steels ◽  
3D Effect

This work presents an investigation of the effects of temperature and crack growth on cleavage fracture toughness for weld thermal simulated X80 pipeline steels in the ductile-to-brittle transition (DBT) regime. A great bulk of fracture toughness (crack tip opening displacement—CTOD) tests and numerical simulations are carried out by deep-cracked single-edge-notched bending (SENB) and shallow-cracked single-edge-notched tension (SENT) specimens at various temperatures (−90 °C, −60 °C, −30 °C, and 0 °C). Three-dimensional (3D) finite element (FE) models of tested specimens have been employed to obtain computational data. The results show that temperature exerts only a slight effect on the material hardening behavior, which indicates the crack tip constraint (as denoted by Q-parameter) is less dependent on the temperature. The measured CTOD-values give considerable scatter but confirm well-established trends of increasing toughness with increasing temperature and reducing constraint. Crack growth and 3D effect exhibited significant influences on CTOD-CMOD relations at higher temperatures, −30 °C and 0 °C for the SENT specimen.

Impact of Metallic Foam’s Microstructure to its Mechanical Property

2013 ◽  
Vol 634-638 ◽  
pp. 2808-2812
Author(s):  
Zhu Feng Sun ◽  
Ling Yun Xie
Keyword(s):  
Fracture Toughness ◽  
Cell Structure ◽  
Crack Tip ◽  
Metallic Foam ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Metal Material ◽  
Loading Mode ◽  
Foam Metal ◽  
Material Fracture

Explored the influence of pore structure of foam metal material on mechanical behavior of fracture. Discuss fracture toughness of several different micro geometric structure of foam metal material with finite element method. The author's calculations showed, microstructure and loading mode has an important effect on the fracture toughness of the foam metal material. due to ignoring the effects of cell structure on the mechanical properties of materials, the classic fracture toughness criterion -crack tip opening displacement (COD) is incomplete, it would be more efficient to take opening displacement change rate of the crack-tip as the parameter to characteristic the metallic foam material fracture toughness.

Sign in / Sign up

Export Citation Format

Share Document