Experimental Validation of Jacobian-Based Stiffness Analysis Method for Parallel Manipulators With Nonredundant Legs

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Antonius G. L. Hoevenaars ◽  
Clément Gosselin ◽  
Patrice Lambert ◽  
Just L. Herder
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Experimental Validation ◽  
Parallel Manipulators ◽  
Parallel Mechanisms ◽  
Analysis Method ◽  
Stiffness Analysis ◽  
Levels Of Detail ◽  
Structural Compliance

A complete stiffness analysis of a parallel manipulator considers the structural compliance of all elements, both in designed degrees-of-freedom (DoFs) and constrained DoFs, and also includes the effect of preloading. This paper presents the experimental validation of a Jacobian-based stiffness analysis method for parallel manipulators with nonredundant legs, which considers all those aspects, and which can be applied to limited-DoF parallel manipulators. The experimental validation was performed by comparing differential wrench measurements with predictions based on stiffness analyses with increasing levels of detail. For this purpose, two passive parallel mechanisms were designed, namely, a planar 3DoF mechanism and a spatial 1DoF mechanism. For these mechanisms, it was shown that a stiffness analysis becomes more accurate if preloading and structural compliance are considered.

Jacobian-based stiffness analysis method for parallel manipulators with non-redundant legs

2015 ◽  
Vol 230 (3) ◽  
pp. 341-352 ◽  
Author(s):  
Antonius GL Hoevenaars ◽  
Patrice Lambert ◽  
Just L Herder
Keyword(s):  
Parallel Manipulator ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Structural Elements ◽  
Analysis Method ◽  
End Effector ◽  
Stiffness Analysis ◽  
Compliant Joints ◽  
Lower Mobility ◽  
Actuated Joints

Stiffness is an important element in the model of a parallel manipulator. A complete stiffness analysis includes the contributions of joints as well as structural elements. Parallel manipulators potentially include both actuated joints, passive compliant joints, and zero stiffness joints, while a leg may impose constraints on the end-effector in the case of lower mobility parallel manipulators. Additionally, parallel manipulators are often designed to interact with an environment, which means that an external wrench may be applied to the end-effector. This paper presents a Jacobian-based stiffness analysis method, based on screw theory, that effectively considers all above aspects and which also applies to parallel manipulators with non-redundant legs.

Determination of the Workspace of a Three-Degrees-of-Freedom Parallel Manipulator Using a Three-Dimensional Computer-Aided-Design Software Package and the Concept of Virtual Chains1

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Andrew Johnson ◽  
Xianwen Kong ◽  
James Ritchie
Keyword(s):  
Computer Aided Design ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Graphical Representation ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Workspace Analysis ◽  
Computer Aided ◽  
Aided Design

The determination of workspace is an essential step in the development of parallel manipulators. By extending the virtual-chain (VC) approach to the type synthesis of parallel manipulators, this technical brief proposes a VC approach to the workspace analysis of parallel manipulators. This method is first outlined before being illustrated by the production of a three-dimensional (3D) computer-aided-design (CAD) model of a 3-RPS parallel manipulator and evaluating it for the workspace of the manipulator. Here, R, P and S denote revolute, prismatic and spherical joints respectively. The VC represents the motion capability of moving platform of a manipulator and is shown to be very useful in the production of a graphical representation of the workspace. Using this approach, the link interferences and certain transmission indices can be easily taken into consideration in determining the workspace of a parallel manipulator.

Dynamic Modeling of a Parallel Manipulator With Three Translational Degrees of Freedom

1998 ◽  
Author(s):  
Richard Stamper ◽  
Lung-Wen Tsai
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Close Agreement ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Kinematic Structure ◽  
End Effector ◽  
Moving Platform ◽  
Euler Approach ◽  
Computationally Intensive

Abstract The dynamics of a parallel manipulator with three translational degrees of freedom are considered. Two models are developed to characterize the dynamics of the manipulator. The first is a traditional Lagrangian based model, and is presented to provide a basis of comparison for the second approach. The second model is based on a simplified Newton-Euler formulation. This method takes advantage of the kinematic structure of this type of parallel manipulator that allows the actuators to be mounted directly on the base. Accordingly, the dynamics of the manipulator is dominated by the mass of the moving platform, end-effector, and payload rather than the mass of the actuators. This paper suggests a new method to approach the dynamics of parallel manipulators that takes advantage of this characteristic. Using this method the forces that define the motion of moving platform are mapped to the actuators using the Jacobian matrix, allowing a simplified Newton-Euler approach to be applied. This second method offers the advantage of characterizing the dynamics of the manipulator nearly as well as the Lagrangian approach while being less computationally intensive. A numerical example is presented to illustrate the close agreement between the two models.

Kinematics, Workspace Optimization, and Performance Evaluation of a 3-Leg 6-DOF Robot in RRRS Configuration

2020 ◽  
Author(s):  
Nathan A. Jensen ◽  
Carl A. Nelson
Keyword(s):  
Performance Evaluation ◽  
Degrees Of Freedom ◽  
Experimental Validation ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Inverse Kinematic ◽  
And Performance ◽  
Workspace Optimization ◽  
Optimization And Performance

Abstract Underactuated parallel manipulators that achieve 6 DOF via multiple controllable degrees of freedom per leg are often pursued and reported due to their large workspaces. This benefit comes at a cost to the manipulator’s performance, however. Such manipulators must then be evaluated in order to characterize their kinematics in terms of position and motion. This paper establishes a pair of inverse kinematic solutions for a previously proposed and prototyped 3-leg, 6-DOF parallel robot. These solutions are then used to define the robot’s workspace with experimental validation and to optimize the robot’s geometry for maximum workspace volume. The linear components of the Jacobian are then defined, allowing for analysis of the manipulability of the robot. The full Jacobian is also defined, and singularities are examined throughout the workspace of the robot.

A Novel Parallel Mechanism With 3-RRUR Legs

2007 ◽  
Author(s):  
Yanwen Li ◽  
Yueyue Zhang ◽  
Lumin Wang ◽  
Zhen Huang
Keyword(s):  
Machine Tools ◽  
Parallel Mechanism ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Forward Kinematics ◽  
Symmetrical Structure ◽  
Forward Kinematic ◽  
Accumulated Error

This paper investigates a novel 4-DOF 3-RRUR parallel manipulator, the number and the characteristics of its degrees of freedom are determined firstly, the rational input plan and the invert and forward kinematic solutions are carried out then. The corresponding numeral example of the forward kinematics is given. This type of parallel manipulators has a symmetrical structure, less accumulated error, and can be used to construct virtual-axis machine tools. The analysis in this paper will play an important role in promoting the application of such manipulators.

A Measure for Evaluation of Maximum Acceleration of Redundant and Nonredundant Parallel Manipulators

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Jun Wu ◽  
Binbin Zhang ◽  
Liping Wang
Keyword(s):  
Dynamic Model ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Virtual Work ◽  
Parallel Manipulators ◽  
Maximum Acceleration ◽  
Virtual Work Principle ◽  
Joint Force ◽  
Joint Forces ◽  
Three Degrees Of Freedom

The paper deals with the evaluation of acceleration of redundant and nonredundant parallel manipulators. The dynamic model of three degrees-of-freedom (3DOF) parallel manipulator is derived by using the virtual work principle. Based on the dynamic model, a measure is proposed for the acceleration evaluation of the redundant parallel manipulator and its nonredundant counterpart. The measure is designed on the basis of the maximum acceleration of the mobile platform when one actuated joint force is unit and other actuated joint forces are less than or equal to a unit force. The measure for evaluation of acceleration can be used to evaluate the acceleration of both redundant parallel manipulators and nonredundant parallel manipulators. Furthermore, the acceleration of the 4-PSS-PU parallel manipulator and its nonredundant counterpart are compared.

Kinematic Synthesis of a Spatial 3-RPS Parallel Manipulator

2003 ◽  
Vol 125 (1) ◽  
pp. 92-97 ◽  
Author(s):  
Han Sung Kim ◽  
Lung-Wen Tsai
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Point Of View ◽  
Dimensional Synthesis ◽  
Kinematic Synthesis ◽  
End Effector ◽  
Solution Methods ◽  
Moving Platform ◽  
At Will

This paper presents the design of spatial 3-RPS parallel manipulators from dimensional synthesis point of view. Since a spatial 3-RPS manipulator has only 3 degrees of freedom, its end effector cannot be positioned arbitrarily in space. It is shown that at most six positions and orientations of the moving platform can be prescribed at will and, given six prescribed positions, there are at most ten RPS chains that can be used to construct up to 120 manipulators. Further, solution methods for fewer than six prescribed positions are also described.

A 2(3-RRPS) parallel manipulator inspired by Gough–Stewart platform

Robotica ◽  
2012 ◽  
Vol 31 (3) ◽  
pp. 381-388 ◽  
Author(s):  
Jaime Gallardo-Alvarado ◽  
Mario A. García-Murillo ◽  
Eduardo Castillo-Castaneda
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Forward Kinematics ◽  
Triangular Prism ◽  
Input Output ◽  
Six Degrees Of Freedom ◽  
Moving Platform

SUMMARYThis study addresses the kinematics of a six-degrees-of-freedom parallel manipulator whose moving platform is a regular triangular prism. The moving and fixed platforms are connected to each other by means of two identical parallel manipulators. Simple forward kinematics and reduced singular regions are the main benefits offered by the proposed parallel manipulator. The Input–Output equations of velocity and acceleration are systematically obtained by resorting to reciprocal-screw theory. A case study, which is verified with the aid of commercially available software, is included with the purpose to exemplify the application of the method of kinematic analysis.

scholarly journals Design and Prototyping of a Partially Decoupled 4-DOF 3T1R Parallel Manipulator With High-Load Carrying Capacity

2008 ◽  
Vol 130 (12) ◽  
Author(s):  
Sébastien Briot ◽  
Vigen Arakelian ◽  
Sylvain Guégan
Keyword(s):  
Carrying Capacity ◽  
Horizontal Plane ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Experimental Validation ◽  
Vertical Axis ◽  
High Load ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Fixed Orientation

In this paper, a new four degrees of freedom 3T1R parallel manipulator with high-load carrying capacity is presented. This manipulator generates Schönflies motions, in which the moving platform carries out three independent translations and one rotation about one axis of fixed orientation. The particularity of the proposed architecture is the decoupling of the displacements of the platform in the horizontal plane from the platform’s translation along the vertical axis. Such a decoupling allows the cancellation of the gravity loads on the actuators, which displace the platform in the horizontal plane. A prototype of the proposed manipulator with four degrees of freedom and an experimental validation of the suggested concept are also presented. Two cases have been examined on the built prototype: a manipulator with payload and one without. It was shown that the input torques of actuators displacing the platform in the horizontal plane for these two cases are the same; i.e., the payload does not bring any load to the actuators.

Motion Reliability Analysis of a 3-RRR Parallel Manipulator With Random and Interval Variables

2016 ◽  
Author(s):  
Zhenhui Zhan ◽  
Xianmin Zhang
Keyword(s):  
Reliability Analysis ◽  
Parallel Manipulator ◽  
Random Variable ◽  
Parallel Manipulators ◽  
Analysis Method ◽  
Motion Error ◽  
Interval Variables ◽  
First Order Second Moment ◽  
Joint Clearances ◽  
Mcs Method

A general methodology for motion error and motion reliability analysis of planar parallel manipulators (PPMs) with random and interval variables is presented. The inherent uncertainties of the manipulator, including tolerances in manufactures, errors in inputs as well as joint clearances are taken into account. The error model of a 3-RRR parallel manipulator is built and the global sensitivity coefficients of motion errors to variations are defined and obtained. The joint clearances are treated as interval variables while the others are treated as random variables. As a result, the motion error of the manipulator could turn out to be the mixture of a random variable and an interval variable. A new motion reliability analysis method based on the First Order Second Moment (FOSM) method and the Monte Carlo simulation (MCS) method is developed for the manipulator with random and interval variables. This paper provides a new idea to better understand the motion reliability affected by the inherent uncertainties of PPMs.

Sign in / Sign up

Export Citation Format

Share Document