A Measure for Evaluation of Maximum Acceleration of Redundant and Nonredundant Parallel Manipulators

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Jun Wu ◽  
Binbin Zhang ◽  
Liping Wang
Keyword(s):  
Dynamic Model ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Virtual Work ◽  
Parallel Manipulators ◽  
Maximum Acceleration ◽  
Virtual Work Principle ◽  
Joint Force ◽  
Joint Forces ◽  
Three Degrees Of Freedom

The paper deals with the evaluation of acceleration of redundant and nonredundant parallel manipulators. The dynamic model of three degrees-of-freedom (3DOF) parallel manipulator is derived by using the virtual work principle. Based on the dynamic model, a measure is proposed for the acceleration evaluation of the redundant parallel manipulator and its nonredundant counterpart. The measure is designed on the basis of the maximum acceleration of the mobile platform when one actuated joint force is unit and other actuated joint forces are less than or equal to a unit force. The measure for evaluation of acceleration can be used to evaluate the acceleration of both redundant parallel manipulators and nonredundant parallel manipulators. Furthermore, the acceleration of the 4-PSS-PU parallel manipulator and its nonredundant counterpart are compared.

Stiffness analysis of the 3SPS+1PS bionic parallel test platform for a hip joint simulator

Robotica ◽  
2013 ◽  
Vol 31 (6) ◽  
pp. 935-944 ◽  
Author(s):  
Gang Cheng ◽  
Jingli Yu ◽  
Peng Xu ◽  
Houguang Liu
Keyword(s):  
Hip Joint ◽  
Stiffness Matrix ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Virtual Work ◽  
Parallel Manipulators ◽  
Parallel Test ◽  
Test Platform ◽  
Global Stiffness Matrix ◽  
Hip Joint Simulator

SUMMARYA novel parallel hip joint simulator, called 3SPS+1PS bionic parallel test platform, with 4 degrees of freedom including three rotations and one translation is designed to represent three-dimensional motion and compound friction movement of a human hip joint and to be a better simulator for testing the tribology performance of biomaterials for hip joint prosthesis. Stiffness is one of the most important performances of parallel manipulators, as well as for the 3SPS+1PS parallel manipulator with higher speeds. First, the differential kinematic/static model was derived based on the kinematics model. The relationship between the elastic deformation of each active leg and the variation of position/orientation deformation of the moving platform was described based on the virtual work principle. Then, a 6 × 6 global stiffness matrix of the 3SPS+1PS parallel manipulator was derived. The maximum versus minimum eigenvalues of the global stiffness matrix were obtained as its two evaluation indexes. By letting the 3SPS+1PS bionic parallel test platform represent three rotation motions and the dynamic loading of the human hip joint as described by ISO 14242 Part-1, the forces acted on each active leg and their responding elastic deformations were analyzed. The distributions for maximum and minimum stiffness in different workspace were detected. Finally, the results showed that the minimum stiffness in the whole workspace should be larger than the allowable stiffness of the 3SPS+1PS parallel manipulator.

On Singularities of Planar Parallel Manipulators

1993 ◽  
Author(s):  
H. R. Mohammadi Daniali ◽  
P. J. Zsombor-Murray ◽  
Jorge Angeles
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Classification Scheme ◽  
Parallel Manipulators ◽  
The Other ◽  
Jacobian Matrices ◽  
General Classification ◽  
Three Degrees Of Freedom ◽  
Planar Parallel Manipulators

Abstract The singularities of the Jacobian matrices of two manipulator with three degrees of freedom are analyzed. One is a planar 3-legged manipulator; the other, a planar double-triangular manipulator. A general classification of parallel-manipulator singularities into three groups is described. The classification scheme relies on the properties of the Jacobian matrices of the manipulator. Finally, the three types of singularity are identified for the two manipulators.

A New Parallel Manipulator With Multiple Operation Modes

2018 ◽  
Vol 10 (5) ◽  
Author(s):  
Jaime Gallardo-Alvarado ◽  
Ramon Rodriguez-Castro
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Robot Manipulator ◽  
Kinematic Chain ◽  
Parallel Manipulators ◽  
Operation Modes ◽  
The Family ◽  
Multiple Operation ◽  
Three Degrees Of Freedom

In this work, a new parallel manipulator with multiple operation modes is introduced. The proposed robot is based on a three-degrees-of-freedom (3DOF) parallel manipulator endowed with a three-dof central kinematic chain, where by blocking some specific kinematic pairs, the robot can modify its mobility. Hence, the robot manipulator is able to assume the role of a limited-dof or a nonredundant parallel manipulator. Without loss of generality, the instantaneous kinematics of one member of the family of parallel manipulators generated by the reconfigurable parallel manipulator, the three-RPRRC + RRPRU nonredundant parallel manipulator with decoupled motions, is approached by means of the theory of screws. For the sake of completeness, the finite kinematics of the robot is also investigated. Numerical examples are included with the purpose to clarify the method of kinematic analysis.

A method for selecting driving system parameters of a new electric shovel's excavating mechanism with three-DOF

2011 ◽  
Vol 225 (11) ◽  
pp. 2661-2672 ◽  
Author(s):  
B Wei ◽  
F Gao ◽  
J Chen ◽  
J He ◽  
X Zhao
Keyword(s):  
Dynamic Model ◽  
Degrees Of Freedom ◽  
Virtual Work ◽  
Transmission Ratio ◽  
Principle Of Virtual Work ◽  
Driving System ◽  
Generalized Coordinates ◽  
System Parameters ◽  
Three Degrees Of Freedom ◽  
Selection Of

Driving system parameters include motor parameters and transmission ratio of the reducer. In this study, a new three-degrees-of-freedom parallel excavating mechanism of electric shovel is analysed for the selection of its driving system which consists of three sub-driving parts. Based on the principle of virtual work in the form of generalized coordinates, the dynamic model of the excavating mechanism is established to calculate the external inertia loads and force (or torque) loads. For this parallel excavating mechanism which has three sub-drives, the external inertia loads cannot be fully divided into three independent parts with respect to these three sub-driving systems. Hence, the dynamic model of the system is employed to get loads characteristic of three sub-driving systems in the excavating process. Thus, the parameters' range of the motors can be obtained and then the best transmission ratio of every reducer can be obtained.

Instantaneous Center of Rotation and Singularities of Planar Parallel Manipulators

2005 ◽  
Vol 33 (3) ◽  
pp. 251-259 ◽  
Author(s):  
H. R. Mohammadi Daniali
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Classification Scheme ◽  
Parallel Manipulators ◽  
Singular Configurations ◽  
Classification Of Singularities ◽  
Instantaneous Center ◽  
Three Degrees Of Freedom ◽  
Planar Parallel Manipulators

With regard to planar parallel manipulators, a general classification of singularities into three groups is given. The classification scheme relies on the properties of instantaneous centers of rotation. This method is very fast and can easily be applied to the manipulators under study. The method is applied to a planar three-degrees-of-freedom parallel manipulator and all its singular configurations are found.

Computation of the safe working zones of Planar and Spatial Parallel Manipulators

Robotica ◽  
2019 ◽  
Vol 38 (5) ◽  
pp. 861-885 ◽  
Author(s):  
Murali K. Karnam ◽  
Aravind Baskar ◽  
Rangaprasad A. Srivatsan ◽  
Sandipan Bandyopadhyay
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Working Zone ◽  
Three Degrees Of Freedom ◽  
Safe Working Zone ◽  
Safe Working

SUMMARYThis paper presents the computation of the safe working zone (SWZ) of a parallel manipulator having three degrees of freedom. The SWZ is defined as a continuous subset of the workspace, wherein the manipulator does not suffer any singularity, and is also free from the issues of link interference and physical limits on its joints. The proposed theory is illustrated via application to two parallel manipulators: a planar 3-R̲RR manipulator and a spatial manipulator, namely, MaPaMan-I. It is also shown how the analyses can be applied to any parallel manipulator having three degrees of freedom, planar or spatial.

Mobility, Kinematic Analysis, and Dimensional Optimization of New Three-Degrees-of-Freedom Parallel Manipulator With Actuation Redundancy

2017 ◽  
Vol 9 (4) ◽  
Author(s):  
Lingmin Xu ◽  
Qinchuan Li ◽  
Ningbin Zhang ◽  
Qiaohong Chen
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Force Transmission ◽  
Transmission Index ◽  
Prismatic Joints ◽  
Redundantly Actuated ◽  
Force Transmissibility ◽  
Solution Velocity ◽  
Three Degrees Of Freedom

Parallel manipulators (PMs) with redundant actuation are attracting increasing research interest because they have demonstrated improved stiffness and fewer singularities. This paper proposes a new redundantly actuated parallel manipulator that has three degrees-of-freedom (DOFs) and four limbs. The proposed manipulator is a 2UPR-2PRU parallel manipulator (where P represents an actuated prismatic joint, R represents a revolute joint, and U represents a universal joint) that is actuated using four prismatic joints; two of these joints are mounted on the base to reduce the movable mass. Mobility analysis shows that the moving platform has two rotational DOFs and one translational DOF. First, the inverse displacement solution, velocity, and singularity analyses are discussed. Next, the local transmission index (LTI) and the good transmission workspace are used to evaluate the motion/force transmissibility of the 2UPR-2PRU parallel manipulator. Finally, the parameter-finiteness normalization method (PFNM) is used to produce an optimal design that considers the good transmission workspace. It is thus shown that the motion/force transmission of the proposed manipulator is improved by optimizing the link parameters.

Determination of the Workspace of a Three-Degrees-of-Freedom Parallel Manipulator Using a Three-Dimensional Computer-Aided-Design Software Package and the Concept of Virtual Chains1

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Andrew Johnson ◽  
Xianwen Kong ◽  
James Ritchie
Keyword(s):  
Computer Aided Design ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Graphical Representation ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Workspace Analysis ◽  
Computer Aided ◽  
Aided Design

The determination of workspace is an essential step in the development of parallel manipulators. By extending the virtual-chain (VC) approach to the type synthesis of parallel manipulators, this technical brief proposes a VC approach to the workspace analysis of parallel manipulators. This method is first outlined before being illustrated by the production of a three-dimensional (3D) computer-aided-design (CAD) model of a 3-RPS parallel manipulator and evaluating it for the workspace of the manipulator. Here, R, P and S denote revolute, prismatic and spherical joints respectively. The VC represents the motion capability of moving platform of a manipulator and is shown to be very useful in the production of a graphical representation of the workspace. Using this approach, the link interferences and certain transmission indices can be easily taken into consideration in determining the workspace of a parallel manipulator.

Sign in / Sign up

Export Citation Format

Share Document