Measurements of Hub Flow Interaction on Film Cooled Nozzle Guide Vane in Transonic Annular Cascade

2015 ◽  
Vol 137 (8) ◽  
Author(s):  
Lamyaa A. El-Gabry ◽  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Film Cooling ◽  
Guide Vane ◽  
Leading Edge ◽  
Field Measurements ◽  
Co2 Concentration ◽  
Horseshoe Vortex ◽  
Mainstream Flow ◽  
Nozzle Guide

An experimental study has been performed in a transonic annular sector cascade of nozzle guide vanes (NGVs) to investigate the aerodynamic performance and the interaction between hub film cooling and mainstream flow. The focus of the study is on the endwalls, specifically the interaction between the hub film cooling and the mainstream. Carbon dioxide (CO2) has been supplied to the coolant holes to serve as tracer gas. Measurements of CO2 concentration downstream of the vane trailing edge (TE) can be used to visualize the mixing of the coolant flow with the mainstream. Flow field measurements are performed in the downstream plane with a five-hole probe to characterize the aerodynamics in the vane. Results are presented for the fully cooled and partially cooled vane (only hub cooling) configurations. Data presented at the downstream plane include concentration contour, axial vorticity, velocity vectors, and yaw and pitch angles. From these investigations, secondary flow structures such as the horseshoe vortex, passage vortex, can be identified and show the cooling flow significantly impacts the secondary flow and downstream flow field. The results suggest that there is a region on the pressure side (PS) of the vane TE where the coolant concentrations are very low suggesting that the cooling air introduced at the platform upstream of the leading edge (LE) does not reach the PS endwall, potentially creating a local hotspot.

Measurements of Hub Flow Interaction on Film Cooled Nozzle Guide Vane in Transonic Annular Cascade

2012 ◽  
Author(s):  
Lamyaa A. El-Gabry ◽  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Film Cooling ◽  
Guide Vane ◽  
Leading Edge ◽  
Field Measurements ◽  
Co2 Concentration ◽  
Pressure Side ◽  
Trailing Edge ◽  
Nozzle Guide

An experimental study has been performed in a transonic annular sector cascade of nozzle guide vanes to investigate the aerodynamic performance and the interaction between hub film cooling and mainstream flow. The focus of the study is on the endwalls, specifically the interaction between the hub film cooling and the mainstream. Carbon dioxide (CO2) has been supplied to the coolant holes to serve as tracer gas. Measurements of CO2 concentration downstream of the vane trailing edge can be used to visualize the mixing of the coolant flow with the mainstream. Flow field measurements are performed in the downstream plane with a 5-hole probe to characterize the aerodynamics in the vane. Results are presented for the fully cooled and partially cooled vane (only hub cooling) configurations. Data presented at the downstream plane include concentration contour, axial vorticity, velocity vectors, and yaw and pitch angles. From these investigations, secondary flow structures such as the horseshoe vortex, passage vortex, can be identified and show the cooling flow significantly impacts the secondary flow and downstream flow field. The results suggest that there is a region on the pressure side of the vane trailing edge where the coolant concentrations are very low suggesting that the cooling air introduced at the platform upstream of the leading edge does not reach the pressure side endwall, potentially creating a local hotspot.

Computational Design and Experimental Evaluation of Using a Leading Edge Fillet on a Gas Turbine Vane

2001 ◽  
Author(s):  
G. A. Zess ◽  
K. A. Thole
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Pressure Gradient ◽  
Gas Turbine ◽  
Total Pressure ◽  
Guide Vane ◽  
Leading Edge ◽  
Field Measurements ◽  
Computational Design ◽  
Horseshoe Vortex

With the desire for increased power output for a gas turbine engine comes the continual push to achieve higher turbine inlet temperatures. Higher temperatures result in large thermal and mechanical stresses particularly along the nozzle guide vane. One critical region along a vane is the leading edge-endwall juncture. Based on the assumption that the approaching flow to this juncture is similar to a two-dimensional boundary layer, previous studies have shown that a horseshoe vortex forms. This vortex forms because of a radial total pressure gradient from the approaching boundary layer. This paper documents the computational design and experimental validation of a fillet placed at the leading edge-endwall juncture of a guide vane to eliminate the horseshoe vortex. The fillet design effectively accelerated the incoming boundary layer thereby mitigating the effect of the total pressure gradient. To verify the CFD studies used to design the leading edge fillet, flow field measurements were performed in a large-scale, linear, vane cascade. The flow field measurements were performed with a laser Doppler velocimeter in four planes orientated orthogonal to the vane. Good agreement between the CFD predictions and the experimental measurements verified the effectiveness of the leading edge fillet at eliminating the horseshoe vortex. The flowfield results showed that the turbulent kinetic energy levels were significantly reduced in the endwall region because of the absence of the unsteady horseshoe vortex.

Effects of Orientation and Position of the Combustor-Turbine Interface on the Cooling of a Vane Endwall

2011 ◽  
Author(s):  
A. A. Thrift ◽  
K. A. Thole ◽  
S. Hada
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Vortex Formation ◽  
Horseshoe Vortex ◽  
Time Resolved ◽  
Image Velocimetry ◽  
Thermal Measurements ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Stagnation Plane

First stage, nozzle guide vanes and accompanying endwalls are extensively cooled by the use of film cooling through discrete holes and leakage flow from the combustor-turbine interface gap. While there are cooling benefits from the interface gap, it is generally not considered as part of the cooling scheme. This paper reports on the effects of the position and orientation of a two-dimensional slot on the cooling performance of a nozzle guide vane endwall. In addition to surface thermal measurements, time-resolved, digital particle image velocimetry (TRDPIV) measurements were performed at the vane stagnation plane. Two slot orientations, 90° and 45°, and three streamwise positions were studied. Effectiveness results indicate a significant increase in area averaged effectiveness for the 45° slot relative to the 90° orientation. Flowfield measurements show dramatic differences in the horseshoe vortex formation.

Interactions Between the Combustor Swirl and the High Pressure Stator of a Turbine

2012 ◽  
Author(s):  
Lucas Giller ◽  
Heinz-Peter Schiffer
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Field Measurements ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Film Cooling Holes ◽  
The Impact

The interaction between the strongly swirling combustor outflow and the high pressure turbine nozzle guide vanes were investigated at the cascade test rig at Technische Universität Darmstadt. The test section of the rig consists of six swirl generators and five cascade vanes. The three middle vanes are equipped with film cooling holes at the leading edges. The swirler nozzles are aligned with the center of the cascade passages. The operating settings are defined by the swirl number, the distance between the swirler nozzles and the vanes, the blowing ratio and the radial angle of the film cooling holes. Flow field measurements using PIV downstream of the swirlers and five hole probe measurements at the inlet and outlet plane of the cascade were accomplished. Measurements using the ammonia diazo technique to determine the adiabatic film cooling effectiveness on the surface of the center cascade vane were also carried out. It is shown that a swirling inflow leads to a strong alteration of the flow field and the losses in the passages in comparison to an axial inflow. Furthermore, the impact of the swirl on the formation of the cooling film and it’s adiabatic film cooling effectiveness is presented.

A New Test Facility to Investigate Film Cooling on a Non-Axisymmetric Contoured Turbine Endwall: Part I — Introduction and Aerodynamic Measurements

2015 ◽  
Author(s):  
Franz Puetz ◽  
Johannes Kneer ◽  
Achmed Schulz ◽  
Hans-Joerg Bauer
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Pressure Distribution ◽  
Film Cooling ◽  
Gas Turbines ◽  
Guide Vane ◽  
Leading Edge ◽  
Suction Side ◽  
Test Facility ◽  
Endwall Contouring

An increased demand for lower emission of stationary gas turbines as well as civil aircraft engines has led to new, low emission combustor designs with less liner cooling and a flattened temperature profile at the outlet. As a consequence, the heat load on the endwall of the first nozzle guide vane is increased. The secondary flow field dominates the endwall heat transfer, which also contributes to aerodynamic losses. A promising approach to reduce these losses is non-axisymmetric endwall contouring. The effects of non-axisymmetric endwall contouring on heat transfer and film cooling are yet to be investigated. Therefore, a new cascade test rig has been set up in order to investigate endwall heat transfer and film cooling on both a flat and a non-axisymmetric contoured endwall. Aerodynamic measurements that have been made prior to the upcoming heat transfer investigation are shown. Periodicity and detailed vane Mach number distributions ranging from 0 to 50% span together with the static pressure distribution on the endwall give detailed information about the aerodynamic behavior and influence of the endwall contouring. The aerodynamic study is backed by an oil paint study, which reveals qualitative information on the effect of the contouring on the endwall flow field. Results show that the contouring has a pronounced effect on vane and endwall pressure distribution and on the endwall flow field. The local increase and decrease of velocity and the reduced blade loading towards the endwall is the expected behavior of the 3d contouring. So are the results of the oil paint visualization, which show a strong change of flow field in the leading edge region as well as that the contouring delays the horse shoe vortex hitting the suction side.

Coal Ash Deposition on Nozzle Guide Vanes: Part I—Experimental Characteristics of Four Coal Ash Types

2011 ◽  
Author(s):  
J. Webb ◽  
B. Casaday ◽  
B. Barker ◽  
J. P. Bons ◽  
A. D. Gledhill ◽  
...  
Keyword(s):  
Film Cooling ◽  
Gas Flow ◽  
Guide Vane ◽  
Ambient Pressure ◽  
Coal Ash ◽  
Leading Edge ◽  
Operating Conditions ◽  
Test Facility ◽  
Gas Temperature ◽  
Nozzle Guide

An accelerated deposition test facility was operated with three different coal ash species to study the effect of ash composition on deposition rate and spatial distribution. The facility seeds a combusting (natural gas) flow with 10–20 micron mass mean diameter coal ash particulate. The particulate-laden combustor exhaust is accelerated through a rectangular-to-annular transition duct and expands to ambient pressure through a nozzle guide vane annular sector. For the present study, the annular cascade consisted of two CFM56 aero-engine vane doublets; comprising three full passages and two half passages of flow. The inlet Mach number (0.1) and gas temperature (1100°C) are representative of operating turbines. Ash samples were tested from the three major coal ranks: lignite, subbituminous, and bituminous. Investigations over a range of inlet gas temperatures from 900°C to 1120°C showed that deposition increased with temperature, though the threshold for deposition varied with ash type. Deposition levels varied with coal rank, with lignite producing the largest deposits at the lowest temperature. Regions of heightened deposition were noted; the leading edge and pressure surface being particularly implicated. Scanning electron microscopy was used to identify deposit structure. For a limited subset of tests, film cooling was employed at nominal design operating conditions but provided minimal protection in cases of severe deposition.

EXPERIMENTAL STUDY OF THE ENDWALL HEAT TRANSFER OF A TRANSONIC NOZZLE GUIDE VANE WITH UPSTREAM JET PURGE COOLING PART 1 - EFFECT OF DENSITY RATIO

2021 ◽  
pp. 1-36
Author(s):  
Shuo Mao ◽  
Ridge A. Sibold ◽  
Wing Ng ◽  
Zhigang LI ◽  
Bo Bai ◽  
...  
Keyword(s):  
Large Scale ◽  
Guide Vane ◽  
Flow Direction ◽  
Density Ratio ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Vital Role ◽  
Blowing Ratio ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract Nozzle guide vane platforms often employ complex cooling schemes to mitigate the ever-increasing thermal loads on endwall. This study analyzes, experimentally and numerically, and describes the effect of coolant to mainstream blowing ratio, momentum ratio and density ratio for a typical axisymmetric converging nozzle guide vane platform with an upstream doublet staggered, steep-injection, cylindrical hole purge cooling scheme. Nominal flow conditions were engine-representative and as follows: Maexit = 0.85, Reexit,Cax = 1.5×106 and an inlet large-scale freestream turbulence intensity of 16%. Two blowing ratios were investigated, each corresponding to the design condition and its upper extrema at M = 2.5 and 3.5, respectively. For each blowing ratio, the coolant to mainstream density ratio was varied between DR=1.2, representing typical experimental neglect of coolant density, and DR=1.95, representative of typical engine conditions. The results show that with a fixed coolant-to-mainstream blowing ratio, the density ratio plays a vital role in the coolant-mainstream mixing and the interaction between coolant and horseshoe vortex near the vane leading edge. A higher density ratio leads to a better coolant coverage immediately downstream of the cooling holes but exposes the in-passage endwall near the pressure side. It also causes the in-passage coolant coverage to decay at a higher rate in the flow direction. From the results gathered, both density ratio and blowing ratio should be considered for accurate testing, analysis, and prediction of purge jet cooling scheme performance.

Comparison of Film Cooling Performance for Different Purge Slot Configurations in a Cylindrical and State-of-the-Art Nozzle Guide Vane

2021 ◽  
Author(s):  
Christian Landfester ◽  
Gunther Müller ◽  
Robert Krewinkel ◽  
Clemens Domnick ◽  
Martin Böhle
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
State Of The Art ◽  
Guide Vane ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract This comparative study is concerned with the advances in nozzle guide vane (NGV) design developments and their influence on the film cooling performance by injecting coolant through the purge slot. An experimental study compares the film cooling effectiveness as well as the aerodynamic effects for different purge slot configurations on both a flat and an axisymmetrically contoured endwall of a NGV. While the flat endwall cascade was equipped with four cylindrical vanes, the contoured endwall cascade consisted of four modern NGVs which represent state-of-the-art high-pressure turbine design standards. Geometric variations, e.g. the purge slot width and injection angle, as well as different blowing ratios (BR) at an engine-like density ratio (DR = 1.6) were realized to investigate the real-life effect of thermal expansion, design modifications and the interaction between secondary flow and coolant. The mainstream flow parameters were set to meet real engine conditions with regard to Reynolds and Mach numbers. The Pressure Sensitive Paint (PSP) technique was used to determine the adiabatic film cooling effectiveness. Five-hole probe measurements (DR = 1.0) were performed to measure the flow field with its characteristic vortex structures as well as the loss distribution in the vane wake region. For a more profound insight into the origin and development of the secondary flows, oil dye visualizations were carried out on both endwalls. The measurement results will be discussed based on a side-by-side comparison of the distribution of film cooling effectiveness on the endwall, its area-averaged values as well as the two-dimensional distribution of total pressure losses and the secondary flow field. The results of this study show that the advances in NGV design development have had a significantly positive influence on the distribution of the coolant. This has to be attributed to lesser disturbance of the coolant propagation by secondary flow for the optimized NGV design, since the design features are intended to suppress the formation of secondary flow. In contrast to the results of the cylindrical profile, sufficient cooling can be already provided with a perpendicular injection in the case of the modern NGV. It is therefore advisable to take these effects into account when designing the film cooling system of a modern high-pressure turbine.

Experimental Investigation of Innovative Cooling Schemes on an Additively Manufactured Engine Scale Turbine Nozzle Guide Vane

2020 ◽  
Author(s):  
Mohammad A. Hossain ◽  
Ali Ameri ◽  
James W. Gregory ◽  
Jeffrey P. Bons
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Leading Edge ◽  
Jet Impingement ◽  
Development Effort ◽  
Suction Surface ◽  
Trailing Edge ◽  
Pin Fin ◽  
Nozzle Guide ◽  
Film Cooling Holes

Abstract This study includes the design, validation, and fabrication via Direct Metal Laser Sintering (DMLS) of a gas turbine nozzle guide vanes (NGV) that incorporates three innovative cooling schemes specifically enabled by additive manufacturing. The novel NGV design is the culmination of an extensive research and development effort over a period of four years that included low and high speed cascade testing coupled with unsteady CFD for numerous candidate innovative cooling architectures. The final vane design (SJ-vane) consists of sweeping jet (SJ) film cooling holes on the suction surface, sweeping jet impingement holes at the leading edge and double-wall partial length triangular pin-fin with impinging jet at the trailing edge. For comparison purposes, a second DMLS enabled vane (777-vane) was designed and fabricated with prototypical cooling circuits to serve as a baseline. This vane consists of a shaped film cooling holes on the suction surface, circular impingement holes at the leading edge and full length cylindrical pin-fins at the trailing edge. Experiments with the two DMLS enabled vanes were performed at the Ohio State University Turbine Reacting Flow Rig (TuRFR) at engine relevant temperature (1375K) and Mach number conditions. Infrared (IR) thermography was utilized to measure the wall temperature of the pressure and suction surface at several coolant mass flow rates to estimate the overall cooling effectiveness (ϕ). Results showed improved cooling performance for the advanced cooling schemes (sweeping jet film cooling, impingement cooling and triangular pin-fin cooling) compared to the baseline cooling schemes.

Coal Ash Deposition on Nozzle Guide Vanes—Part I: Experimental Characteristics of Four Coal Ash Types

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
J. Webb ◽  
B. Casaday ◽  
B. Barker ◽  
J. P. Bons ◽  
A. D. Gledhill ◽  
...  
Keyword(s):  
Film Cooling ◽  
Gas Flow ◽  
Guide Vane ◽  
Ambient Pressure ◽  
Coal Ash ◽  
Leading Edge ◽  
Operating Conditions ◽  
Test Facility ◽  
Gas Temperature ◽  
Nozzle Guide

An accelerated deposition test facility was operated with four different coal ash species to study the effect of ash composition on deposition rate and spatial distribution. The facility seeds a combusting (natural gas) flow with 10–20 micron mass mean diameter coal ash particulate. The particulate-laden combustor exhaust is accelerated through a rectangular-to-annular transition duct and expands to ambient pressure through a nozzle guide vane annular sector. For the present study, the annular cascade consisted of two CFM56 aero-engine vane doublets, comprising three full passages and two half passages of flow. The inlet Mach number (0.1) and gas temperature (1100 °C) are representative of operating turbines. Ash samples were tested from the three major coal ranks: lignite, subbituminous, and bituminous. Investigations over a range of inlet gas temperatures from 900 °C to 1120 °C showed that deposition increased with temperature, though the threshold for deposition varied with ash type. Deposition levels varied with coal rank, with lignite producing the largest deposits at the lowest temperature. Regions of heightened deposition were noted; the leading edge and pressure surface being particularly implicated. Scanning electron microscopy was used to identify deposit structure. For a limited subset of tests, film cooling was employed at nominal design operating conditions but provided minimal protection in cases of severe deposition.

Sign in / Sign up

Export Citation Format

Share Document