Interactions Between the Combustor Swirl and the High Pressure Stator of a Turbine

2012 ◽  
Author(s):  
Lucas Giller ◽  
Heinz-Peter Schiffer
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Field Measurements ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Film Cooling Holes ◽  
The Impact

The interaction between the strongly swirling combustor outflow and the high pressure turbine nozzle guide vanes were investigated at the cascade test rig at Technische Universität Darmstadt. The test section of the rig consists of six swirl generators and five cascade vanes. The three middle vanes are equipped with film cooling holes at the leading edges. The swirler nozzles are aligned with the center of the cascade passages. The operating settings are defined by the swirl number, the distance between the swirler nozzles and the vanes, the blowing ratio and the radial angle of the film cooling holes. Flow field measurements using PIV downstream of the swirlers and five hole probe measurements at the inlet and outlet plane of the cascade were accomplished. Measurements using the ammonia diazo technique to determine the adiabatic film cooling effectiveness on the surface of the center cascade vane were also carried out. It is shown that a swirling inflow leads to a strong alteration of the flow field and the losses in the passages in comparison to an axial inflow. Furthermore, the impact of the swirl on the formation of the cooling film and it’s adiabatic film cooling effectiveness is presented.

Rib Turbulator Effects on Crossflow-Fed Shaped Film Cooling Holes

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Dale W. Fox ◽  
Fraser B. Jones ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
...  
Keyword(s):  
Film Cooling ◽  
Velocity Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Smooth Channel ◽  
Cooling Hole ◽  
Film Cooling Holes ◽  
Inlet Position ◽  
The Impact

Most studies of turbine airfoil film cooling in laboratory test facilities have used relatively large plenums to feed flow into the coolant holes. However, a more realistic inlet condition for the film cooling holes is a relatively small channel. Previous studies have shown that the film cooling performance is significantly degraded when fed by perpendicular internal crossflow in a smooth channel. In this study, angled rib turbulators were installed in two geometric configurations inside the internal crossflow channel, at 45 deg and 135 deg, to assess the impact on film cooling effectiveness. Film cooling hole inlets were positioned in both prerib and postrib locations to test the effect of hole inlet position on film cooling performance. A test was performed independently varying channel velocity ratio and jet to mainstream velocity ratio. These results were compared to the film cooling performance of previously measured shaped holes fed by a smooth internal channel. The film cooling hole discharge coefficients and channel friction factors were also measured for both rib configurations with varying channel and inlet velocity ratios. Spatially averaged film cooling effectiveness is largely similar to the holes fed by the smooth internal crossflow channel, but hole-to-hole variation due to inlet position was observed.

Effect of Freestream Turbulence Intensity on Film Cooling Jet Structure and Surface Effectiveness Using PIV and PSP

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Michael D. Clemenson
Keyword(s):  
Turbulence Intensity ◽  
Film Cooling ◽  
Field Measurements ◽  
Freestream Turbulence ◽  
Mean Velocity ◽  
Cooling Effectiveness ◽  
Piv Measurements ◽  
Film Cooling Effectiveness ◽  
Film Cooling Holes ◽  
Jet Structure

An experimental investigation of film cooling jet structure using two-dimensional particle image velocimetry (PIV) has been completed for cylindrical, simple angle (θ=35 deg) film cooling holes. The PIV measurements are coupled with detailed film cooling effectiveness distributions on the flat plate obtained using a steady state, pressure sensitive paint (PSP) technique. Both the flow and surface measurements were performed in a low speed wind tunnel where the freestream turbulence intensity was varied from 1.2% to 12.5%. With this traditional film cooling configuration, the blowing ratio was varied from 0.5 to 1.5 to compare the jet structure of relatively low and high momentum cooling flows. Velocity maps of the coolant flow (in the streamwise direction) are obtained on three planes spanning a single hole: centerline, 0.25D, and 0.5D (outer edge of the film cooling hole). From the seeded jets, time averaged, mean velocity distributions of the film cooling jets are obtained near the cooled surface. In addition, turbulent fluctuations are obtained for each flow condition. Combining the detailed flow field measurements obtained using PIV (both instantaneous and time averaged) with detailed film cooling effectiveness distributions on the surface (PSP) provides a more complete view of the coolant jet-mainstream flow interaction. Near the edge of the film cooling holes, the turbulent mixing increases, and as a result the film cooling effectiveness decreases. Furthermore, the PIV measurements show the increased mixing of the coolant jet with the mainstream at the elevated freestream turbulence level resulting in a reduction in the jet to effectively protect the film cooled surface.

Effect of Flow Acceleration on Mainstream-to-Coolant Flow Interaction for Round and Shaped Film Cooling Holes

2017 ◽  
Author(s):  
Kyle R. Vinton ◽  
Lesley M. Wright
Keyword(s):  
Flow Field ◽  
Pressure Gradient ◽  
Film Cooling ◽  
Field Measurements ◽  
Stereoscopic Particle Image Velocimetry ◽  
Film Cooling Effectiveness ◽  
Flow Acceleration ◽  
Favorable Pressure Gradient ◽  
Density Ratios ◽  
Film Cooling Holes

Film cooling flow fields under a favorable, mainstream pressure gradient have been experimentally investigated at various blowing and density ratios. Three dimensional velocity and vorticity distributions have been obtained above a flat plate with cylindrical holes (θ = 30°) and laidback, fanshaped holes (θ = 30°, β = γ = 10°) using the stereoscopic particle image velocimetry (S-PIV) technique. In a low speed wind tunnel, accelerating flows were studied with density ratios of 1 and 3. The effect of blowing ratio was also studied by varying the ratio from 0.5 to 1.5. With a flow acceleration parameter comparable to previous investigations, the effect of flow acceleration on these film cooling flows is presented. The flow field measurements were performed at two planes near the film cooling holes (x/d = 0 and the downstream edge) for both the round and shaped holes. These flow field measurements provide a foundation for understanding the flow interactions that produce various film cooling effectiveness and heat transfer coefficient distributions on the surface of the airfoil. The S-PIV measurements show that a favorable pressure gradient reduces jet separation and increases the width of the jet and counter rotating vortex pair. The effects are caused by the thinning of the boundary layer that occurs in favorable pressure gradient flows.

Optimal Arrangement of the Film Cooling Holes Considering the Manufacturing Tolerance for High Pressure Turbine Nozzle

2016 ◽  
Author(s):  
Sanga Lee ◽  
Dong-Ho Rhee ◽  
Kwanjung Yee
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Leading Edge ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Manufacturing Tolerance ◽  
Cooling Hole ◽  
Film Cooling Holes

In spite of a myriad of researches on the optimal shape of film cooling holes, only a few attempts have been made to optimize the hole arrangement for film cooling so far. Moreover, although the general scale of film cooling hole is so small that manufacturing tolerance has substantial effects on the cooling performance of turbine, the researches on this issue are even scarcer. If it is possible to obtain optimal hole arrangement which not only improve the film cooling performance but also is robust to the manufacturing tolerance, then overall cooling performance of a turbine would become more reliable and useful from the practical point of view. To this end, the present study proposed a robust design optimization procedure which takes the manufacturing uncertainties into account. The procedure was subsequently applied to the film cooling holes on high pressure turbine nozzle pressure side to obtain the robust array shape under the uncertainty of the manufacturing tolerance. First, the array of the holes was parameterized by 5 design variables using the newly suggested shape functions, and 2 representative factors were considered for the manufacturing tolerance of the film cooling hole. Probabilistic process that consists of Kriging surrogate model and Monte Carlo Simulation with descriptive sampling method was coupled with the design optimization process using Genetic Algorithm. Through this, film cooling hole array which shows the high performance, yet robust to the manufacturing tolerance was obtained, and the effects of the manufacturing tolerance on the cooling performance was carefully investigated. As a result, the region where the film cooling effectiveness is noticeable, as well as the maximum width of the variation of the film cooling effectiveness were reduced through optimization, and it is also confirmed that the tolerance of the holes near the leading edge is more influential to the cooling performance because the film cooling effectiveness is more sensitive to the manufacturing tolerance of the leading edge than that of the trailing edge.

Experimental and Computational Comparisons of Fan-Shaped Film-Cooling on a Turbine Vane Surface

2005 ◽  
Author(s):  
W. Colban ◽  
K. A. Thole ◽  
M. Haendler
Keyword(s):  
Turbulence Model ◽  
Film Cooling ◽  
Turbulence Models ◽  
Complex Flow ◽  
Ir Camera ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Film Cooling Holes

The flow exiting the combustor in a gas turbine engine is considerably hotter than the melting temperature of the turbine section components, of which the turbine nozzle guide vanes see the hottest gas temperatures. One method used to cool the vanes is to use rows of film-cooling holes to inject bleed air that is lower in temperature through an array of discrete holes onto the vane surface. The purpose of this study was to evaluate the row-by-row interaction of fan-shaped holes as compared to the performance of a single row of fan-shaped holes in the same locations. This study presents adiabatic film-cooling effectiveness measurements from a scaled-up, two-passage vane cascade. High resolution film-cooling measurements were made with an infrared (IR) camera at a number of engine representative flow conditions. Computational fluid dynamics (CFD) predictions were also made to evaluate the performance of some of the current turbulence models in predicting a complex flow such as turbine film-cooling. The RNG k-ε turbulence model gave a closer prediction of the overall level of film-effectiveness, while the v2-f turbulence model gave a more accurate representation of the flow physics seen in the experiments.

Effect of Freestream Turbulence Intensity on Film Cooling Jet Structure and Surface Effectiveness Using PIV and PSP

2010 ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Michael D. Clemenson
Keyword(s):  
Turbulence Intensity ◽  
Film Cooling ◽  
Field Measurements ◽  
Freestream Turbulence ◽  
Mean Velocity ◽  
Cooling Effectiveness ◽  
Piv Measurements ◽  
Film Cooling Effectiveness ◽  
Film Cooling Holes ◽  
Jet Structure

An experimental investigation of film cooling jet structure using two-dimensional, particle image velocimetry (PIV) has been completed for cylindrical, simple angle (θ = 35°) film cooling holes. The PIV measurements are coupled with detailed film cooling effectiveness distributions on the flat plate obtained using a steady state, pressure sensitive paint (PSP) technique. Both the flow and surface measurements were performed in a low speed wind tunnel where the freestream turbulence intensity was varied from 1.2% to 12.5%. With this traditional film cooling configuration, the blowing ratio was varied from 0.5–1.5 to compare the jet structure of relatively low and high momentum cooling flows. Velocity maps of the coolant flow (in the streamwise direction) are obtained on three planes spanning a single hole: centerline, 0.25D, and 0.5D (outer edge of the film cooling hole). From the seeded jets, time averaged, mean velocity distributions of the film cooling jets are obtained near the cooled surface. In addition, turbulent fluctuations are obtained for each flow condition. Combining the detailed flow field measurements obtained using PIV (both instantaneous and time averaged) with detailed film cooling effectiveness distributions on the surface (PSP), provides a more complete view of the coolant jet–mainstream flow interaction. Near the edge of the film cooling holes, the turbulent mixing increases, and as a result the film cooling effectiveness decreases. Furthermore, the PIV measurements show the increased mixing of the coolant jet with the mainstream at the elevated freestream turbulence level resulting in a reduction of the jet to effectively protect the film cooled surface.

Optimization of Film Cooling Holes on the Suction Surface of a High Pressure Turbine Blade

2012 ◽  
Author(s):  
Carole El Ayoubi ◽  
Wahid Ghaly ◽  
Ibrahim Hassan
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Three Dimensional ◽  
Suction Surface ◽  
Cfd Simulations ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss ◽  
Flow Parameters ◽  
Film Cooling Holes

This paper aims to optimize film coolant flow parameters on the suction surface of a high-pressure gas turbine blade in order to obtain an optimum compromise between a high film cooling effectiveness and a low aerodynamic loss. An optimization algorithm coupled with three-dimensional Reynolds-averaged Navier Stokes (RANS) analysis is used to determine the optimum film cooling configuration. The VKI blade with two staggered rows of axially oriented, conically flared, film cooling holes on its suction surface is considered. Two design variables are selected; the coolant to mainstream temperature ratio and total pressure ratio. The effect of varying these coolant flow parameters on the film cooling effectiveness and the aerodynamic loss is analyzed using an optimization method and three dimensional steady CFD simulations. The optimization process involves a genetic algorithm and a response surface approximation of the artificial neural network type to provide low-fidelity predictions of the objective function. The CFD simulations are performed using the commercial software CFX. The numerical predictions of the aerodynamics and wall heat transfer are validated against experimental data. The optimization objective consists of maximizing the spatially averaged film cooling effectiveness and minimizing the aerodynamic penalty produced by film cooling. The results of this optimization are reported in terms of the aerodynamic loss and adiabatic cooling effectiveness.

Rib Turbulator Effects on Crossflow-Fed Shaped Film Cooling Holes

2018 ◽  
Author(s):  
Dale W. Fox ◽  
Fraser B. Jones ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
...  
Keyword(s):  
Film Cooling ◽  
Velocity Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Smooth Channel ◽  
Cooling Hole ◽  
Film Cooling Holes ◽  
Inlet Position ◽  
The Impact

Most studies of turbine airfoil film cooling in laboratory test facilities have used relatively large plenums to feed flow into the coolant holes. However, a more realistic inlet condition for the film cooling holes is a relatively small channel. Previous studies have shown that the film cooling performance is significantly degraded when fed by perpendicular internal crossflow in a smooth channel. In this study, angled rib turbulators were installed in two geometric configurations inside the internal crossflow channel, at 45° and 135°, to assess the impact on film cooling effectiveness. Film cooling hole inlets were positioned in both pre-rib and post-rib locations to test the effect of hole inlet position on film cooling performance. A test was performed independently varying channel velocity ratio and jet to mainstream velocity ratio. These results were compared to the film cooling performance of previously measured shaped holes fed by a smooth internal channel. The film cooling hole discharge coefficients and channel friction factors were also measured for both rib configurations with varying channel and inlet velocity ratios. Spatially-averaged film cooling effectiveness is largely similar to the holes fed by the smooth internal crossflow channel, but hole-to-hole variation due to inlet position was observed.

Experimental and Computational Comparisons of Fan-Shaped Film Cooling on a Turbine Vane Surface

2006 ◽  
Vol 129 (1) ◽  
pp. 23-31 ◽  
Author(s):  
W. Colban ◽  
K. A. Thole ◽  
M. Haendler
Keyword(s):  
Turbulence Model ◽  
Film Cooling ◽  
Turbulence Models ◽  
Infrared Camera ◽  
Complex Flow ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Film Cooling Holes

The flow exiting the combustor in a gas turbine engine is considerably hotter than the melting temperature of the turbine section components, of which the turbine nozzle guide vanes see the hottest gas temperatures. One method used to cool the vanes is to use rows of film-cooling holes to inject bleed air that is lower in temperature through an array of discrete holes onto the vane surface. The purpose of this study was to evaluate the row-by-row interaction of fan-shaped holes as compared to the performance of a single row of fan-shaped holes in the same locations. This study presents adiabatic film-cooling effectiveness measurements from a scaled-up, two-passage vane cascade. High-resolution film-cooling measurements were made with an infrared camera at a number of engine representative flow conditions. Computational fluid dynamics predictions were also made to evaluate the performance of some of the current turbulence models in predicting a complex flow such as turbine film-cooling. The renormalization group (RNG) k‐ε turbulence model gave a closer prediction of the overall level of film effectiveness, while the v2‐f turbulence model gave a more accurate representation of the flow physics seen in the experiments.

Sign in / Sign up

Export Citation Format

Share Document