Direct Geometrico-Static Problem of Underconstrained Cable-Driven Parallel Robots With Three Cables1

2013 ◽  
Vol 5 (3) ◽  
Author(s):  
Marco Carricato
Keyword(s):  
Complete Solution ◽  
Static Problem ◽  
Parallel Robots ◽  
Homotopy Continuation ◽  
Complex Field ◽  
Efficient Computation ◽  
End Effector ◽  
Tensile Forces ◽  
Univariate Polynomial ◽  
The Ideal

This paper studies the direct geometrico-static problem (DGP) of underconstrained cable-driven parallel robots (CDPRs) with three cables. The task consists in determining the end-effector pose and the cable tensile forces when the cable lengths are assigned. The problem is challenging, because kinematics and statics are coupled, and they must be tackled simultaneously. An effective elimination procedure is proposed and a least-degree univariate polynomial free of spurious factors is obtained in the ideal governing the problem. This is proven to admit 156 solutions in the complex field. Several approaches for the efficient computation of the complete solution set are presented, including an eigenproblem formulation and homotopy continuation.

Inverse Geometrico-Static Problem of Underconstrained Cable-Driven Parallel Robots With Three Cables1

2013 ◽  
Vol 5 (3) ◽  
Author(s):  
Marco Carricato
Keyword(s):  
Complete Solution ◽  
Static Problem ◽  
Parallel Robots ◽  
Solution Sets ◽  
Real Solutions

This paper studies underconstrained cable-driven parallel robots (CDPRs) with three cables. A major challenge in the study of these robots is the intrinsic coupling between kinematics and statics, which must be tackled simultaneously. Effective elimination procedures are presented which provide the complete solution sets of the inverse geometrico-static problems (IGPs) with assigned orientation or position. In the former case, the platform orientation is given, whereas the platform position and the cable lengths and tensions must be computed. In the latter case, the platform position is known, whereas the platform orientation and the cable lengths and tensions are to be calculated. The described problems are proven to admit at the most 1 and 24 real solutions, respectively.

Simultaneous base and tool calibration for self-calibrated parallel robots

Robotica ◽  
2002 ◽  
Vol 20 (4) ◽  
pp. 367-374 ◽  
Author(s):  
Guilin Yang ◽  
I-Ming Chen ◽  
Song Huat Yeo ◽  
Wee Kiat Lim
Keyword(s):  
Parallel Robot ◽  
Parallel Robots ◽  
Sufficient Accuracy ◽  
Least Square ◽  
Mobile Platform ◽  
Calibration Model ◽  
End Effector ◽  
The World ◽  
Kinematic Transformation ◽  
Kinematic Errors

In this paper, we focus on the base and tool calibration of a self-calibrated parallel robot. After the self-calibration of a parellel robot by using the built-in sensors in the passive joints, its kinematic transformation from the robot base to the mobile platform frame can be computed with sufficient accuracy. The base and tool calibration, hence, is to identify the kinematic errors in the fixed transformations from the world frame to the robot base frame and from the mobile platform frame to the tool (end-effector) frame in order to improve the absolute positioning accuracy of the robot. Using the mathematical tools from group theory and differential geometry, a simultaneous base and tool calibration model is formulated. Since the kinematic errors in a kinematic transformation can be represented by a twist, i.e. an element of se(3), the resultant calibration model is simple, explicit and geometrically meaningful. A least-square algorithm is employed to iteratively identify the error parameters. The simulation example shows that all the preset kinematic errors can be fully recovered within three to four iterations.

scholarly journals Modal Kinematic Analysis of a Parallel Kinematic Robot with Low-Stiffness Transmissions

Robotics ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 132
Author(s):  
Paolo Righettini ◽  
Roberto Strada ◽  
Filippo Cortinovis
Keyword(s):  
High Speed ◽  
Parallel Robots ◽  
Maximum Speed ◽  
Kinematic Structure ◽  
End Effector ◽  
New Approach ◽  
Working Space ◽  
Modes Of Vibration ◽  
Parallel Kinematic ◽  
Actuated Joints

Several industrial robotic applications that require high speed or high stiffness-to-inertia ratios use parallel kinematic robots. In the cases where the critical point of the application is the speed, the compliance of the main mechanical transmissions placed between the actuators and the parallel kinematic structure can be significantly higher than that of the parallel kinematic structure itself. This paper deals with this kind of system, where the overall performance depends on the maximum speed and on the dynamic behavior. Our research proposes a new approach for the investigation of the modes of vibration of the end-effector placed on the robot structure for a system where the transmission’s compliance is not negligible in relation to the flexibility of the parallel kinematic structure. The approach considers the kinematic and dynamic coupling due to the parallel kinematic structure, the system’s mass distribution and the transmission’s stiffness. In the literature, several papers deal with the dynamic vibration analysis of parallel robots. Some of these also consider the transmissions between the motors and the actuated joints. However, these works mainly deal with the modal analysis of the robot’s mechanical structure or the displacement analysis of the transmission’s effects on the positioning error of the end-effector. The discussion of the proposed approach takes into consideration a linear delta robot. The results show that the system’s natural frequencies and the directions of the end-effector’s modal displacements strongly depend on its position in the working space.

scholarly journals Synthesis of Spatial RPRP Closed Linkages for a Given Screw System

2011 ◽  
Vol 3 (2) ◽  
Author(s):  
Alba Perez-Gracia
Keyword(s):  
Design Method ◽  
Parallel Robots ◽  
Synthesis Problem ◽  
Dimensional Synthesis ◽  
End Effector ◽  
Serial Chain

The dimensional synthesis of spatial chains for a prescribed set of positions can be applied to the design of parallel robots by joining the solutions of each serial chain at the end-effector. This design method does not provide with the knowledge about the trajectory between task positions and, in some cases, may yield a system with negative mobility. These problems can be avoided for some overconstrained but movable linkages if the finite-screw system associated with the motion of the linkage is known. The finite-screw system defining the motion of the robot is generated by a set of screws, which can be related to the set of finite task positions traditionally used in the synthesis theory. The interest of this paper lies in presenting a method to define the whole workspace of the linkage as the input task for the exact dimensional synthesis problem. This method is applied to the spatial RPRP closed linkage, for which one solution exists.

Stiffness estimation of a parallel manipulator using image analysis and camera calibration techniques

Robotica ◽  
2012 ◽  
Vol 31 (4) ◽  
pp. 657-667 ◽  
Author(s):  
Abraham Gonzalez-Hernandez ◽  
Eduardo Castillo-Castaneda
Keyword(s):  
Image Analysis ◽  
Camera Calibration ◽  
Parallel Manipulator ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Mobile Platform ◽  
End Effector ◽  
Simple Implementation ◽  
Specific Position ◽  
Calibration Techniques

SUMMARYThis work presents a methodology using image analysis to estimate the experimental stiffness of a parallel robot, Parallix LKF-2040, a 3-degree-of-freedom manipulator. The proposed methodology has a simple implementation and can be applied to different architectures of parallel robots. This methodology uses image analysis and camera calibration techniques to estimate compliant displacements of mobile platform produced by several loads at the end effector level, and calculate stiffness in a specific position of mobile platform. Experimental results are presented for different positions within the workspace.

Solving the Geometric Design Problem of Spatial 3R Robot Manipulators Using Polynomial Homotopy Continuation

2002 ◽  
Vol 124 (4) ◽  
pp. 652-661 ◽  
Author(s):  
Eric Lee ◽  
Constantinos Mavroidis
Keyword(s):  
Design Problem ◽  
Free Choice ◽  
Robot Manipulators ◽  
Continuation Method ◽  
Geometric Design ◽  
Design Parameters ◽  
Homotopy Continuation ◽  
Serial Link ◽  
End Effector ◽  
Homotopy Continuation Method

In this paper, the geometric design problem of serial-link robot manipulators with three revolute (R) joints is solved using a polynomial homotopy continuation method. Three spatial positions and orientations are defined and the dimensions of the geometric parameters of the 3-R manipulator are computed so that the manipulator will be able to place its end-effector at these three pre-specified locations. Denavit and Hartenberg parameters and 4×4 homogeneous matrices are used to formulate the problem and obtain eighteen design equations in twenty-four design unknowns. Six of the design parameters are set as free choices and their values are selected arbitrarily. Two different cases for selecting the free choices are considered and their design equations are solved using polynomial homotopy continuation. In both cases for free choice selection, eight distinct manipulators are found that will be able to place their end-effector at the three specified spatial positions and orientations.

A new method to solve robot inverse kinematics using Assur virtual chains

Robotica ◽  
2009 ◽  
Vol 27 (7) ◽  
pp. 1017-1026 ◽  
Author(s):  
H. Simas ◽  
R. Guenther ◽  
D. F. M. da Cruz ◽  
D. Martins
Keyword(s):  
Exponential Stability ◽  
Numerical Integration ◽  
Numerical Algorithm ◽  
Inverse Kinematics ◽  
Integration Method ◽  
Parallel Robots ◽  
New Method ◽  
Numerical Integration Method ◽  
End Effector ◽  
Novel Method

SUMMARYThis paper describes a numerical algorithm to solve the inverse kinematics of parallel robots based on numerical integration. Inverse kinematics algorithms based on numerical integration involve the drift phenomena of the solution; as a consequence, errors are generated when the end-effector location differs from that desired. The proposed algorithm associates a novel method to describe the differential kinematics with a simple numerical integration method. The methodology is presented in this paper and its exponential stability is proved. A numerical example and a real application are presented to outline its advantages.

scholarly journals Design of a Wearable Haptic Device for Hand Palm Cutaneous Feedback

2021 ◽  
Vol 8 ◽  
Author(s):  
Mihai Dragusanu ◽  
Alberto Villani ◽  
Domenico Prattichizzo ◽  
Monica Malvezzi
Keyword(s):  
Design Guidelines ◽  
Point Of View ◽  
Haptic Device ◽  
End Effector ◽  
Main Design ◽  
Cutaneous Feedback ◽  
Tensile Forces ◽  
Grasping And Manipulation ◽  
Tangential Forces ◽  
Structural Point

This study describes the main design and prototyping steps of a novel haptic device for cutaneous stimulus of a hand palm. This part of the hand is fundamental in several grasping and manipulation tasks, but is still less exploited in haptics applications than other parts of the hand, as for instance the fingertips. The proposed device has a parallel tendon-based mechanical structure and is actuated by three motors positioned on the hand’s back. The device is able to apply both normal and tangential forces and to render the contact with surfaces with different slopes. The end-effector can be easily changed to simulate the contact with different surface curvatures. The design is inspired by a smaller device previously developed for the fingertips; however, in the device presented in this study, there are significant differences due to the wider size, the different form-factor, and the structure of hand palm. The hand palm represents the support for the fingers and is connected to the arm through the wrist. The device has to be developed taking into account fingers’ and wrist’s motions, and this requirement constrains the number of actuators and the features of the transmission system. The larger size of the palm and the higher forces challenge the device from a structural point of view. Since tendons can apply only tensile forces, a spring-based support has been developed to keep the end-effector separated from the palm when the device is not actuated or when the force to be rendered is null. The study presents the main design guidelines and the main features of the proposed device. A prototype has been realized for the preliminary tests, and an application scenario with a VR environment is introduced.

Gateway Configuration for Rapid Pick-and-Place Operations of 2-Degrees-of-Freedom Parallel Robots

2020 ◽  
Vol 13 (1) ◽  
Author(s):  
Andrea Martin-Parra ◽  
David Rodriguez-Rosa ◽  
Sergio Juarez-Perez ◽  
Guillermo Rubio-Gomez ◽  
Antonio Gonzalez-Rodriguez ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Degrees Of Freedom ◽  
Jacobian Matrix ◽  
Parallel Robots ◽  
End Effector ◽  
Joint Coordinates ◽  
Pick And Place ◽  
Low Energy Consumption ◽  
Simulation Results ◽  
The Difference

Abstract This article presents a new assembling for 2 degrees-of-freedom (DOFs) parallel robots for executing rapid pick-and-place operations with low energy consumption. A conventional design of 2-DOF parallel robots is based on five-bar mechanisms. Collisions between links are highly possible, restricting the end-effector workspace and/or increasing the trajectory time to avoid collisions. In this article, an alternative assembling for preventing collisions is presented. This novel assembling allows exploring the difference between the four five-bar mechanism configurations for the same position of the end-effector. Some of these configurations yield to lower time and/or lower energy consumption for the same motorization. First, a dynamic model of the robot has been developed using matlab® and simulink® and validated by comparison with the results obtained by adams® software. A robust cascade PD regulator for controlling joint coordinates has been tuned providing a high accurate end-effector positioning. Finally, simulation results of four configurations are presented for executing controlled maneuvers. The obtained results demonstrate that the conventional configuration is the worst one in terms of trajectory time or energy consumption and, conversely, the best one corresponds to an uncommonly used configuration. A workspace map where all configurations provide faster maneuvers has been obtained in terms of Jacobian matrix and mechanism elbows distance. The results presented here allow designing a rapid manipulator for pick-and-place operations.

Sign in / Sign up

Export Citation Format

Share Document