scholarly journals Synthesis of Spatial RPRP Closed Linkages for a Given Screw System

2011 ◽  
Vol 3 (2) ◽  
Author(s):  
Alba Perez-Gracia
Keyword(s):  
Design Method ◽  
Parallel Robots ◽  
Synthesis Problem ◽  
Dimensional Synthesis ◽  
End Effector ◽  
Serial Chain

The dimensional synthesis of spatial chains for a prescribed set of positions can be applied to the design of parallel robots by joining the solutions of each serial chain at the end-effector. This design method does not provide with the knowledge about the trajectory between task positions and, in some cases, may yield a system with negative mobility. These problems can be avoided for some overconstrained but movable linkages if the finite-screw system associated with the motion of the linkage is known. The finite-screw system defining the motion of the robot is generated by a set of screws, which can be related to the set of finite task positions traditionally used in the synthesis theory. The interest of this paper lies in presenting a method to define the whole workspace of the linkage as the input task for the exact dimensional synthesis problem. This method is applied to the spatial RPRP closed linkage, for which one solution exists.

Kinematic Synthesis of Spatial R-R Dyads for Path Following Revisited Using the Rotation Matrix Approach

1999 ◽  
Author(s):  
Venkat Krovi ◽  
G. K. Ananthasuresh ◽  
Vijay Kumar
Keyword(s):  
Linear System ◽  
Path Following ◽  
Rotation Matrix ◽  
Dimensional Synthesis ◽  
Kinematic Synthesis ◽  
End Effector ◽  
Serial Chain ◽  
Systematic Development ◽  
Matrix Vector ◽  
Selection Of

Abstract We revisit the dimensional synthesis of a spatial two-link, two revolute-jointed serial chain for path following applications, focussing on the systematic development of the design equations and their analytic solution for the three precision point synthesis problem. The kinematic design equations are obtained from the equations of loop-closure for end-effector position in rotation-matrix/vector form at the three precision points. These design equations form a rank-deficient linear system in the link-vector components. The nullspace of the rank deficient linear system is then deduced analytically and interpreted geometrically. Tools from linear algebra are applied to systematically create the auxiliary conditions required for synthesis and to verify consistency. An analytic procedure for obtaining the link-vector components is then developed after a suitable selection of free choices. Optimization over the free choices is possible to permit the matching of additional criteria and explored further. Examples of the design of optimal two-link coupled spatial R-R dyads are presented where the end-effector interpolates three positions exactly and closely approximates an entire desired path.

Dimensional Synthesis of Planar Eight-Bar Linkages Based on a Parallel Robot With a Prismatic Base Joint

2013 ◽  
Author(s):  
Gim Song Soh ◽  
Fangtian Ying
Keyword(s):  
Rigid Body ◽  
Design Process ◽  
Parallel Robot ◽  
Degree Of Freedom ◽  
Dimensional Synthesis ◽  
End Effector ◽  
Prismatic Joint ◽  
Serial Chain ◽  
Different Types

This paper details the dimensional synthesis for the rigid body guidance of planar eight-bar linkages that could be driven by a prismatic joint at its base. We show how two RR cranks can be added to a planar parallel robot formed by a PRR and 3R serial chain to guide its end-effector through a set of five task poses. This procedure is useful for designers who require the choice of ground pivot locations. The results are eight different types of one-degree of freedom planar eight-bar linkages. We demonstrate the design process with the design of a multifunctional wheelchair that could transform its structure between a self-propelled wheelchair and a walking guide.

Workspace and Singularity Characteristics of 3-DOF Planar Parallel Robots

2009 ◽  
Author(s):  
Ming Huang
Keyword(s):  
Computer Simulations ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Geometric Parameters ◽  
Kinematic Structure ◽  
Link Length ◽  
End Effector ◽  
Serial Chain ◽  
Parametric Studies ◽  
Position And Orientation

A study of workspace and singularity characteristics is presented for two common types of 3-DOF planar parallel robot manipulators. The robots considered feature a kinematic structure with 3 in-parallel actuated, R-R-R and R-P-R serial chain geometries. In this study, computer simulations aided with graphic visualization were used to characterize the complete pose workspace (for ranges of both position and orientation) and the singularity inherent to the systems. Parametric studies have also been performed to ascertain the way in which both characteristics vary with respect to various geometric parameters such as pivot location, link length, and platform size for end-effector. Results are shown by way of a unique composite ratio of the available workspace to the density of singularity within that workspace.

The Dimensional Synthesis of Planar Parallel Cable-Driven Mechanisms Through Convex Relaxations

2012 ◽  
Vol 4 (3) ◽  
Author(s):  
K. Azizian ◽  
P. Cardou
Keyword(s):  
Interval Analysis ◽  
Scaling Factor ◽  
Linear Program ◽  
Synthesis Problem ◽  
Feasibility Problem ◽  
Nonlinear Program ◽  
Convex Relaxations ◽  
Dimensional Synthesis ◽  
End Effector

The wrench-closure workspace (WCW) of parallel cable-driven mechanisms is the set of poses for which any wrench can be produced at the end-effector by a set of positive cable tensions. In this paper, we tackle the dimensional synthesis problem, namely, that of finding a geometry for a planar parallel cable-driven mechanism (PPCDM) whose WCW contains a prescribed workspace. To this end, we first recall a linear program to determine whether a given pose is inside or outside the WCW of a given PPCDM. The relaxation of this linear program over a box leads to a nonlinear feasibility problem that can only be satisfied when this box is completely inside the WCW. We extend this feasibility problem to find a PPCDM geometry whose WCW includes a given set of boxes. These boxes represent the prescribed workspace or an estimate thereof, which may be obtained through interval analysis. Finally, we introduce a nonlinear program through which the PPCDM geometry is changed while maximizing the scaling factor of the prescribed set of boxes. When the optimum scaling factor is greater or equal to one, the WCW of the resulting PPCDM contains the set of boxes.

scholarly journals Backstepping Sliding Mode Robust Control for a Wire-Driven Parallel Robot Based on a Nonlinear Disturbance Observer

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Yuqi Wang ◽  
Qi Lin ◽  
Lei Zhou ◽  
Xinxin Shi ◽  
Lei Wang
Keyword(s):  
Robust Control ◽  
Disturbance Observer ◽  
Control Method ◽  
Sliding Mode ◽  
Design Method ◽  
Parallel Robot ◽  
Parallel Robots ◽  
End Effector ◽  
Nonlinear Disturbance Observer ◽  
Nonlinear Disturbance

Based on a nonlinear disturbance observer, a backstepping sliding mode robust control is proposed for a wire-driven parallel robot (WDPR) system used in the wind tunnel test to dominate the motion of the end effector. The control method combines both the merits of backstepping control and sliding mode robust control. The WDPR is subject to different types of disturbances, and these disturbances will affect the motion precision of the end effector. To overcome these problems, a nonlinear disturbance observer (NDO) is designed to reject such disturbances. In this study, the design method of the nonlinear disturbance observer does not require the reliable dynamic model of the WDPR. Moreover, the design method can be used not only in the WDPR but also in other parallel robots. Then, a backstepping design method is adopted and a sliding mode term is introduced to construct a desired controller, and the disturbances are compensated in the controller to reduce the switching gain and guarantee the robustness. For the sake of verifying the stabilization of the closed-loop system, the Lyapunov function is constructed to analyze the stabilization of the system. Finally, the feasibility and validity of the proposed control scheme are proved through both simulation and experimental results.

Kinematic and Kinetostatic Synthesis of Planar Coupled Serial Chain Mechanisms

2002 ◽  
Vol 124 (2) ◽  
pp. 301-312 ◽  
Author(s):  
Venkat Krovi ◽  
G. K. Ananthasuresh ◽  
Vijay Kumar
Keyword(s):  
Degree Of Freedom ◽  
Dimensional Synthesis ◽  
Single Degree Of Freedom ◽  
End Effector ◽  
Solution Approach ◽  
Single Degree ◽  
Design Specifications ◽  
Serial Chain ◽  
Gear Trains ◽  
External Loads

Single Degree-of-freedom Coupled Serial Chain (SDCSC) mechanisms form a novel class of modular and compact mechanisms with a single degree-of-freedom, suitable for a number of manipulation tasks. Such SDCSC mechanisms take advantage of the hardware constraints between the articulations of a serial-chain linkage, created using gear-trains or belt/pulley drives, to guide the end-effector motions and forces. In this paper, we examine the dimensional synthesis of such SDCSC mechanisms to perform desired planar manipulation tasks, taking into account task specifications on both end-effector motions and forces. Our solution approach combines precision point synthesis with optimization to realize optimal mechanisms, which satisfy the design specifications exactly at the selected precision points and approximate them in the least-squares sense elsewhere along a specified trajectory. The designed mechanisms can guide a rigid body through several positions while supporting arbitrarily specified external loads. Furthermore, torsional springs are added at the joints to reduce the overall actuation requirements and to enhance the task performance. Examples from the kinematic and the kinetostatic synthesis of planar SDCSC mechanisms are presented to highlight the benefits.

Seven-Position Synthesis of a Spatial Eight-Bar Linkage by Constraining a TRS Serial Chain

2009 ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Degree Of Freedom ◽  
Upper Arm ◽  
End Effector ◽  
Serial Chain ◽  
Position Synthesis ◽  
Two Degree Of Freedom ◽  
Puma Robot

In this paper, we use seven-position synthesis to add four TS constraints to a TRS serial chain robot and obtain a two degree-of-freedom spatial eight-bar linkage. The TRS chain is an elbow manipulator, similar to a PUMA robot. We synthesize a TS dyad to connect the base of the robot to its forearm, and then we synthesize three TS dyads that connect the upper arm of the robot to its end-effector. The result is a two degree-of-freedom spatial eight-bar linkage that moves through seven prescribed positions. It consists of a TRST loop supporting a 3TS-RS platform, which we denote as a TS-TRS-3TS spatial linkage. We formulate and solve the design equations for the TS dyads, and analyze the resulting eight-bar linkage. An example demonstrates our results.

Integrated optimal design of a high-speed planar parallel manipulator

2018 ◽  
Vol 233 (9) ◽  
pp. 2976-2990 ◽  
Author(s):  
Zhengsheng Chen ◽  
Minxiu Kong
Keyword(s):  
Optimal Design ◽  
Parallel Manipulator ◽  
High Speed ◽  
Design Method ◽  
Tracking Error ◽  
Dimensional Synthesis ◽  
Tracking Accuracy ◽  
Nsga Ii ◽  
Parameters Tuning ◽  
Planar Parallel Manipulator

To obtain excellent comprehensive performances of the planar parallel manipulator for the high-speed application, an integrated optimal design method, which integrated dimensional synthesis, motors/reducers selection, and control parameters tuning, is proposed, and the 3RRR parallel manipulator was taken as the example. The kinematic and dynamic performances of condition number, velocity index, acceleration capability, and low-order frequency are taken into accounts for the dimensional synthesis. Then, to match motors/reducers parameters and keep an economical cost, the constraint equations and the parameters library are built, and the cost is chosen as one of the optimization objectives. Also, to get high tracking accuracy, the dynamic forward plus proportional–derivative control scheme is introduced, and the tracking error is chosen as one of the optimization objectives. Hence, the optimization model including dimensional synthesis, motors/reducers selection and controller parameters tuning is established, which is solved by the genetic algorithm II (NSGA-II). The result shows that comprehensive performances can be effectively promoted through the proposed integrated optimal design, and the prototype was constructed according to the Pareto-optimal front.

Simultaneous base and tool calibration for self-calibrated parallel robots

Robotica ◽  
2002 ◽  
Vol 20 (4) ◽  
pp. 367-374 ◽  
Author(s):  
Guilin Yang ◽  
I-Ming Chen ◽  
Song Huat Yeo ◽  
Wee Kiat Lim
Keyword(s):  
Parallel Robot ◽  
Parallel Robots ◽  
Sufficient Accuracy ◽  
Least Square ◽  
Mobile Platform ◽  
Calibration Model ◽  
End Effector ◽  
The World ◽  
Kinematic Transformation ◽  
Kinematic Errors

In this paper, we focus on the base and tool calibration of a self-calibrated parallel robot. After the self-calibration of a parellel robot by using the built-in sensors in the passive joints, its kinematic transformation from the robot base to the mobile platform frame can be computed with sufficient accuracy. The base and tool calibration, hence, is to identify the kinematic errors in the fixed transformations from the world frame to the robot base frame and from the mobile platform frame to the tool (end-effector) frame in order to improve the absolute positioning accuracy of the robot. Using the mathematical tools from group theory and differential geometry, a simultaneous base and tool calibration model is formulated. Since the kinematic errors in a kinematic transformation can be represented by a twist, i.e. an element of se(3), the resultant calibration model is simple, explicit and geometrically meaningful. A least-square algorithm is employed to iteratively identify the error parameters. The simulation example shows that all the preset kinematic errors can be fully recovered within three to four iterations.

scholarly journals Modal Kinematic Analysis of a Parallel Kinematic Robot with Low-Stiffness Transmissions

Robotics ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 132
Author(s):  
Paolo Righettini ◽  
Roberto Strada ◽  
Filippo Cortinovis
Keyword(s):  
High Speed ◽  
Parallel Robots ◽  
Maximum Speed ◽  
Kinematic Structure ◽  
End Effector ◽  
New Approach ◽  
Working Space ◽  
Modes Of Vibration ◽  
Parallel Kinematic ◽  
Actuated Joints

Several industrial robotic applications that require high speed or high stiffness-to-inertia ratios use parallel kinematic robots. In the cases where the critical point of the application is the speed, the compliance of the main mechanical transmissions placed between the actuators and the parallel kinematic structure can be significantly higher than that of the parallel kinematic structure itself. This paper deals with this kind of system, where the overall performance depends on the maximum speed and on the dynamic behavior. Our research proposes a new approach for the investigation of the modes of vibration of the end-effector placed on the robot structure for a system where the transmission’s compliance is not negligible in relation to the flexibility of the parallel kinematic structure. The approach considers the kinematic and dynamic coupling due to the parallel kinematic structure, the system’s mass distribution and the transmission’s stiffness. In the literature, several papers deal with the dynamic vibration analysis of parallel robots. Some of these also consider the transmissions between the motors and the actuated joints. However, these works mainly deal with the modal analysis of the robot’s mechanical structure or the displacement analysis of the transmission’s effects on the positioning error of the end-effector. The discussion of the proposed approach takes into consideration a linear delta robot. The results show that the system’s natural frequencies and the directions of the end-effector’s modal displacements strongly depend on its position in the working space.

Sign in / Sign up

Export Citation Format

Share Document