Fretting Wear and Fretting Fatigue—How Are They Related?

1983 ◽  
Vol 105 (2) ◽  
pp. 230-238 ◽  
Author(s):  
R. C. Bill

Results from published literature and results obtained by the author are examined in detail to determine how fretting wear and fretting fatigue are related. The effects of various experimental parameters, including slip amplitude, number of fretting cycles, frequency of fretting motion, experimental atmosphere, temperature, and the performance of coatings and surface treatments, are surveyed. All of the results examined indicate that fretting wear and fretting fatigue are influenced in a consistent and analogous manner by controlled variations in experimental conditions. That is, conditions that tend to accelerate fretting wear also accelerate fretting fatigue failures. Correlation of the performance of coatings on material under fretting wear and fretting fatigue conditions is rather tenuous, partly because similar contact conditions for fretting fatigue and fretting wear are not available for very many materials.

2002 ◽  
Vol 37 (6) ◽  
pp. 519-533 ◽  
Author(s):  
M-C Dubourg ◽  
Y Berthier ◽  
L Vincent

Fretting is one of the plagues of modern industry. It occurs whenever a junction between components is subjected to cyclic sliding, with small relative displacements at the interface of the contacting surfaces. Further cyclic bulk stresses may be superimposed on to one or both components. The investigation of fretting wear and fretting fatigue started in the early 1970s. It is responsible for premature fatigue failures and often limits the life of a component. Crack initiation and growth under fretting contact conditions have been investigated. The fretting map concepts allow the first degradation responses of the material—no degradation, cracking and wear—to be related to a fretting regime with its corresponding local contact conditions during fretting tests. The fretting fatigue prediction models have been developed and compared to experiments conducted either on metallic or photoelastic materials. A special emphasis has been directed towards crack nucleation and early growth during stage I, the stage I-stage II transition and stage II crack growth (crack initiation sites, orientation, growth path, formation of a branch, growth mechanism). The analysis of the different stages that comprise the crack lifetime has been carried out in order to understand the effects of diverse parameters that are thought to influence the fretting damage.


2021 ◽  
Vol 22 (1) ◽  
Author(s):  
An Zheng ◽  
Michael Lamkin ◽  
Yutong Qiu ◽  
Kevin Ren ◽  
Alon Goren ◽  
...  

Abstract Background A major challenge in evaluating quantitative ChIP-seq analyses, such as peak calling and differential binding, is a lack of reliable ground truth data. Accurate simulation of ChIP-seq data can mitigate this challenge, but existing frameworks are either too cumbersome to apply genome-wide or unable to model a number of important experimental conditions in ChIP-seq. Results We present ChIPs, a toolkit for rapidly simulating ChIP-seq data using statistical models of key experimental steps. We demonstrate how ChIPs can be used for a range of applications, including benchmarking analysis tools and evaluating the impact of various experimental parameters. ChIPs is implemented as a standalone command-line program written in C++ and is available from https://github.com/gymreklab/chips. Conclusions ChIPs is an efficient ChIP-seq simulation framework that generates realistic datasets over a flexible range of experimental conditions. It can serve as an important component in various ChIP-seq analyses where ground truth data are needed.


1998 ◽  
Vol 31 (11) ◽  
pp. 701-711 ◽  
Author(s):  
B.J. Briscoe ◽  
A. Chateauminois ◽  
T.C. Lindley ◽  
D. Parsonage

Author(s):  
J. Armand ◽  
L. Pesaresi ◽  
L. Salles ◽  
C. W. Schwingshackl

Accurate prediction of the vibration response of aircraft engine assemblies is of great importance when estimating both the performance and the lifetime of its individual components. In the case of underplatform dampers, for example, the motion at the frictional interfaces can lead to a highly nonlinear dynamic response and cause fretting wear at the contact. The latter will change the contact conditions of the interface and consequently impact the nonlinear dynamic response of the entire assembly. Accurate prediction of the nonlinear dynamic response over the lifetime of the assembly must include the impact of fretting wear. A multi-scale approach that incorporates wear into the nonlinear dynamic analysis is proposed, and its viability is demonstrated for an underplatform damper system. The nonlinear dynamic response is calculated with a multiharmonic balance approach, and a newly developed semi-analytical contact solver is used to obtain the contact conditions at the blade-damper interface with high accuracy and low computational cost. The calculated contact conditions are used in combination with the energy wear approach to compute the fretting wear at the contact interface. The nonlinear dynamic model of the blade-damper system is then updated with the worn profile and its dynamic response is recomputed. A significant impact of fretting wear on the nonlinear dynamic behaviour of the blade-damper system was observed, highlighting the sensitivity of the nonlinear dynamic response to changes at the contact interface. The computational speed and robustness of the adopted multi-scale approach are demonstrated.


1988 ◽  
Vol 110 (3) ◽  
pp. 517-524 ◽  
Author(s):  
Y. Berthier ◽  
Ch. Colombie´ ◽  
L. Vincent ◽  
M. Godet

Fretting wear and fretting fatigue are governed by the rate of formation of materials (third-bodies) between the initial contact surfaces. Furthermore, the third-bodies must be maintained within the contact. The issue of the race between third-body formation and subsurface damage conditions the effect of fretting on fatigue. That race lasts for only a few hundred or at best a few thousand cycles. Effective third-bodies (or good anti-fretting lubricants) must adhere strongly to the rubbing surfaces, and be able to accommodate at least part of the relative displacement. Great care in the design of test equipment has to be exercised before definitive results on the effect of amplitude and frequency on either fretting fatigue or fretting wear can be obtained for a given contact condition, given materials and given environments.


2021 ◽  
Vol 11 (40) ◽  
pp. 168-169
Author(s):  
Denise Lessa Aleixo ◽  
Leoni Vilano Bonamin ◽  
Silvana Marques De Araujo

Introduction: The use of homeopathic medicines has increased, once traditional medicines sometimes do not produce the desired effects and because side effects sometimes compromise the treatment. In recent years, research on homeopathy has clearly developed, both in the implementation of more consistent methodologies and in the description of the data and published methods, improvement are still required in these matters. The acknowledgment of homeopathy depends on the credibility of the groups researching this topic Objective: list and criticize articles highlighting main effects, schedule of treatment and potencies used in different animals models. Material and Methods: A review of articles published since 2000 in journals indexed in the PubMed/Scielo databases was performed. Keywords used were parasitosis/homeopathy and parasitosis/ultra-diluted, in English and Portuguese. Specialized journals such as Homeopathy, International Journal of High Dilution Research, and Brazilian Homeopathic Journal were also used. The contents of each issue of these journals were examined for the "Use of highly diluted medication in parasitic infections." Results and Discussion: Thirty nine papers have been gathered. The methodology of the articles surveyed did not meet the requirements listed in the REHBaR[1]. Thirty seven reports have shown the benefits/effects of highly diluted medicine in the treatment of infectious diseases. In models where experimental conditions are carefully controlled, the conclusions follow the same pattern as those observed in the treatment of farm animals, where, even without completely controlled conditions, clinical result is positive. In fourteen reports using the same model, eight where animals were treated in a constant and prolonged way shown a better result, compared with six reports in which animals were treated for a short period of time, receiving a single daily dose. Several authors have conducted clinical trials using commercial formulas, which do not always provide their composition and/or dynamization, making it difficult to reproducing the experiment. In some of the articles, it was not mentioned if the experiments were repeated at least twice. Conclusions: In parasitic infections, the effect of homeopathic medications is still controversial, and the experimental parameters for evaluation shoud be carefully chosen to avoid isolated analyses of data. Researchers should consider results regarding environmental and sanitary conditions of the animal as a whole. The improvement of techniques and expansion of knowledge about highly diluted medicines may lead to a viable alternative to treat parasitic infections. Precise and detailed descriptions will contribute to advances in the use of homeopathy, so that the wider community can benefit, in practice, from these findings. Keywords: homeopathy, parasitic infections, CAM (Complementary and Alternative Medicine). Reference [1] Lüdtke R, Musial F, Wijk R, Witt C, Baumgartner S. Reporting experiments in homeopathic basic research (REHBaR) – A detailed guideline for authors. Homeopathy. 2009; 98:287-298.


Author(s):  
Chiara Gastaldi ◽  
Johann Gross ◽  
Maren Scheel ◽  
Teresa M. Berruti ◽  
Malte Krack

Abstract Dry friction devices such as underplatform dampers are commonly included in turbine bladed disks designs to mitigate structural vibrations and avoid high cycle fatigue failures. The design of frictionally damped bladed disks requires adequate models to represent the friction contact. A widely used approach connects contact node pairs with normal and tangential springs and a Coulomb friction law. This simple model architecture is effective in capturing the softening behavior typically observed on frictionally damped structures subjected to increasing forcing levels. An unexpected hardening behavior was observed on the frequency response functions of two-blades-plus-damper system tested by the authors in a controlled laboratory environment. The reason behind this unexpected behavior will be carefully analyzed and linked to the damper kinematics and to the dependence of contact elasticity on the contact pressure. The inadequacy of contact models with constant spring values will be discussed and alternatives will be proposed. The importance of being able to represent complex contact conditions in order to effectively predict the system dynamics is shown here using a laboratory demonstrator, however its implications are relevant to any other case where large contact pressure variations are to be expected. The nonlinear steady state simulations of the blades-plus-damper system will be carried out using an in-house code exploiting the Multi-Harmonic Balance Method (MHBM) in combination with the Alternating Frequency Time (AFT) Method.


Sign in / Sign up

Export Citation Format

Share Document