Optimum Design Technique for Rotating Wheels

1988 ◽  
Vol 110 (1) ◽  
pp. 41-44
Author(s):  
T. Hattori ◽  
H. Ohnishi ◽  
M. Taneda
Keyword(s):  
Optimum Design ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Rotating Disk ◽  
Design System ◽  
Design Technique ◽  
Gas Temperature ◽  
Design Program ◽  
Bearing Load ◽  
Flow Compressor

Compressor rotors and turbine rotors are subject to centrifugal and thermal loads. These loads increase proportionally with tip speed, pressure ratio, and gas temperature. On the other hand, the rotor weight must be lessened to improve rotor dynamics and restrict bearing load. Thus, an optimum design technique is required, which offers the lightest possible wheel shape under the stress limit restriction. This paper introduces an optimum design system developed for turbomachinery rotors, and discusses several application results. The sequential linear programming method is used in the optimizing process, and centrifugal and thermal stress analyses of variable thickness rotating wheels are performed using Donath’s method. This system’s validity is confirmed by application to uniform-strength rotating disk problems and comparison with analytical results. This optimum design program is then applied to the design of axial flow compressor wheels.

scholarly journals Optimum Design Technique for Rotating Wheels

1986 ◽  
Author(s):  
Toshio Hattori ◽  
Hiroo Ohnishi ◽  
Motoharu Taneda
Keyword(s):  
Optimum Design ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Rotating Disk ◽  
Design System ◽  
Design Technique ◽  
Gas Temperature ◽  
Design Program ◽  
Bearing Load ◽  
Flow Compressor

Compressor rotors and turbine rotors are subject to centrifugal and thermal loads. These loads increase proportionally with tip speed, pressure ratio and gas temperature. On the other hand, the rotor weight must be lessened to improve rotor dynamics and restrict bearing load. Thus, an optimum design technique is required, which offers the lighest possible wheel shape under the stress limit restriction. This paper introduces an optimum design system developed for turbo machinery rotors, and discusses several application results. The sequential linear programming method is used in the optimizing process, and centrifugal and thermal stress analyses of variable thickness rotating wheels are performed using Donath’s method. This system’s validity is confirmed by application to uniform strength rotating disk problems and comparison with analytical results. This optimum design program is then applied to the design of axial flow compressor wheels.

Optimum Design of Rotational Wheel and Casing Structures Under Transient Thermal and Centrifugal Loads

1992 ◽  
Author(s):  
T. Hattori ◽  
H. Toriya
Keyword(s):  
Optimum Design ◽  
Thermal Analyses ◽  
Axial Flow ◽  
Tip Clearance ◽  
Design System ◽  
Ring Model ◽  
Bearing Loads ◽  
Stress And Deformation ◽  
Flow Compressor ◽  
Transient Thermal

Abstract Transient thermal and centrifugal loads on turbomachinery rotors have increased with recent increases in gas temperatures and tip speeds. Rotor weights must be decreased to improve rotor dynamics and to reduce bearing loads. Moreover, blade tip clearance must be decreased to improve aerodynamic efficiency. An optimum design technique offering the lightest possible wheel shape under specified stress and clearance limits is therefore required. This paper introduces an optimum design system developed for turbo-machinery rotors. Sequential linear programming is used in the optimizing process, and non-steady-state thermal analyses of wheels and casings are performed by numerically analyzing multi-ring models. Stress and deformation analyses of these wheels and casings are performed by using Donath’s method with the same multi-ring model. This optimum design program is applied to the design of multistage axial flow compressor wheels.

Numerical Efforts of Aerodynamic Re-Design in a Single-Stage Transonic Axial Compressor: Part 1 — Stator Design

2017 ◽  
Author(s):  
Justin (Jongsik) Oh
Keyword(s):  
Pressure Ratio ◽  
Axial Compressor ◽  
Axial Flow ◽  
Single Stage ◽  
Design Flow ◽  
Design Parameters ◽  
Original Design ◽  
Circular Arc ◽  
Surge Margin ◽  
Flow Compressor

In many aerodynamic design parameters for the axial-flow compressor, three variables of tailored blading, blade lean and sweep were considered in the re-design efforts of a transonic single stage which had been designed in 1960’s NASA public domains. As Part 1, the re-design was limited to the stator vane only. For the original MCA (Multiple Circular Arc) blading, which had been applied at all radii, the CDA (Controlled Diffusion Airfoil) blading was introduced at midspan as the first variant, and the endwalls of hub and casing (or tip) were replaced with the DCA (Double Circular Arc) blading for the second variant. Aerodynamic performance was predicted through a series of CFD analysis at design speed, and the best aerodynamic improvement, in terms of pressure ratio/efficiency and operability, was found in the first variant of tailored blading. It was selected as a baseline for the next design efforts with blade lean, sweep and both combined. Among 12 variants, a case of positively and mildly leaned blades was found the most attractive one, relative to the original design, providing benefits of an 1.0% increase of pressure ratio at design flow, an 1.7% increase of efficiency at design flow, a 10.5% increase of the surge margin and a 32.3% increase of the choke margin.

Design and Development of a 12:1 Pressure Ratio Compressor for the Ruston 6-MW Gas Turbine

1982 ◽  
Author(s):  
F. Carchedi ◽  
G. R. Wood
Keyword(s):  
Gas Turbine ◽  
Test Data ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Aerodynamic Design ◽  
Design And Development ◽  
Surge Line ◽  
Flow Compressor ◽  
Industrial Gas Turbine ◽  
Spanwise Flow

This paper describes the design and development of a 15-stage axial flow compressor for a −6MW industrial gas turbine. Detailed aspects of the aerodynamic design are presented together with rig test data for the complete characteristic including stage data. Predictions of spanwise flow distributions are compared with measured values for the front stages of the compressor. Variable stagger stator blading is used to control the position of the low speed surge line and the effects of the stagger changes are discussed.

Progress of the 40 MW-Class Advanced Humid Air Turbine Tests

2013 ◽  
Vol 135 (11) ◽  
Author(s):  
Manabu Yagi ◽  
Hidefumi Araki ◽  
Hisato Tagawa ◽  
Tomomi Koganezawa ◽  
Chihiro Myoren ◽  
...  
Keyword(s):  
Metal Surface ◽  
Control Method ◽  
Cooling System ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Test Facility ◽  
Humid Air ◽  
Air Turbine ◽  
Calculation Results ◽  
Flow Compressor

A 40 MW-class test facility has been constructed to verify practicability of applying the advanced humid air turbine (AHAT) system to a heavy-duty gas turbine. Verification tests have been carried out from January 2012, and interaction effects between the key components were established. First, water atomization cooling (WAC) was confirmed to contribute to both increased mass flow rate and pressure ratio for the axial-flow compressor. The good agreement between measured and calculated temperatures at the compressor discharge was also confirmed. These results demonstrated the accuracy of the developed prediction model for the WAC. Second, a control method that realized both flame stability and low nitrogen oxides (NOx) emissions was verified. Although the power output and air humidity were lower than the rated values, NOx concentration was about 10 ppm. Finally, a hybrid nozzle cooling system, which utilized both compressor discharged air and humid air, was developed and tested. The metal surface temperatures of the first stage nozzles were measured, and they were kept under the permissible metal temperature. The measured temperatures on the metal surface reasonably corresponded with calculation results.

Development of a 6 MW-Class High-Efficiency Gas Turbine M7A-01

1994 ◽  
Author(s):  
T. Sugimoto ◽  
K. Ikesawa ◽  
S. Kajita ◽  
W. Karasawa ◽  
T. Kojima ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
High Efficiency ◽  
Axial Flow ◽  
Inlet Temperature ◽  
Gas Temperature ◽  
Flow Compressor ◽  
Exhaust Gas Temperature ◽  
Cycle Efficiency

The M7A-01 gas turbine is a newly developed 6 MW class single-shaft machine. With its high simple-cycle efficiency and high exhaust gas temperature. it is particularly suited for use in electric power generation and co-generation applications. An advanced high efficiency axial-flow compressor, six can-type combustors, and a high inlet temperature turbine has been adopted. This results in a high thermal efficiency of 31.5% at the gas turbine output shaft and a high overall thermal efficiency of co-generation system. In addition, low NOx emissions from the combustors and a long service life permit long-term continuous operation under various environmental limitations. The results of the full load shop test, accelerated cyclic endurance test and extra severity tests verified that the performance, the mechanical characteristics and the emission have satisfied the initial design goals.

Numerical Simulation of Steady Air Injection Flow Control Effects on a Transonic Axial Flow Compressor

2012 ◽  
Vol 224 ◽  
pp. 352-357
Author(s):  
Islem Benhegouga ◽  
Ce Yang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Leading Edge ◽  
Air Injection ◽  
Axial Flow Compressor ◽  
Blade Tip ◽  
Flow Compressor

In this work, steady air injection upstream of the blade leading edge was used in a transonic axial flow compressor, NASA rotor 37. The injectors were placed at 27 % upstream of the axial chord length at blade tip, the injection mass flow rate is 3% of the chock mass flow rate, and 3 yaw angles were used, respectively -20°, -30°, and -40°. Negative yaw angles were measured relative to the compressor face in opposite direction of rotational speeds. To reveal the mechanism, steady numerical simulations were performed using FINE/TURBO software package. The results show that the stall mass flow can be decreased about 2.5 %, and an increase in the total pressure ratio up to 0.5%.

Investigation of an Axial Flow Compressor With Variable Reynolds Number and Inlet Casing Geometry

1978 ◽  
Author(s):  
B. Becker ◽  
O. von Schwerdtner ◽  
J. Günther
Keyword(s):  
Reynolds Number ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Flow Distribution ◽  
Pressure Level ◽  
Symmetric Flow ◽  
Flow Compressor ◽  
Gas Turbine Compressor ◽  
Theoretical Results

In the course of developing the compressor of a 100-MW gas turbine, extensive measurements took place on a test compressor provided with the four front stages scaled down to 1:4.63. The performance investigations have been supplemented by measurements of flow distribution down- and upstream of the blading, as well as at various intermediate axial positions. The test stand, operating in a closed circuit, allowed for the variation of the Reynolds number by changing the pressure level. The geometry of the inlet casing was variable as well, thus enabling the comparison of results with axial, two- and one-sided inlet flows. In this connection, the vibrational behavior of the rotating blades, besides the aerodynamics of the compressor, have been investigated. In case of the inlet casing with a two-sided inflow, additional flow field analyses have been performed using a model without compressor blading. The theoretical results calculated under the assumption of a rotational-symmetric flow, as well as the measurements at the gas turbine compressor itself, are used for comparison. The gas turbine compressor operating with a mass flow of 483 kg/s at ISO-conditions and a pressure ratio of 10 is running in the highest performance range of single-shaft compressors in operation today.

CFD Analysis to Investigate the Effect of Vortex Generators on a Transonic Axial Flow Compressor Stage

2015 ◽  
Author(s):  
Avinash Kumar Rajendran ◽  
M. T. Shobhavathy ◽  
R. Ajith Kumar
Keyword(s):  
Pressure Ratio ◽  
Cross Flow ◽  
Axial Flow ◽  
Vortex Generator ◽  
Leading Edge ◽  
Vortex Generators ◽  
Stall Margin ◽  
Compressor Rotor ◽  
Flow Compressor ◽  
End Wall

The performance of the compressor blade is considerably influenced by secondary flow effects, like the cross flow on the end wall as well as corner flow separation between the wall and the blade. Computational Fluid Dynamics (CFD) has been extensively used to analyze the flow through rotating machineries, in general and through axial compressors, in particular. The present work is focused on the studying the effects of Vortex Generator (VG) on test compressor at CSIR National Aerospace Laboratories, Bangalore, India using CFD. The compressor consists of NACA transonic rotor with 21 blades and subsonic stator with 18 vanes. The design pressure ratio is 1.35 at 12930 RPM with a mass flow rate of 22 kg/s. Three configurations of counter rotating VGs were selected for the analysis with 0.25δ, 0.5δ and δ height, where δ was equal to the physical thickness of boundary layer (8mm) at inlet to the compressor rotor [11]. The vortex generators were placed inside the casing at 18 percent of the chord ahead to the leading edge of the rotor. A total of 63 pairs of VGs were incorporated, with three pairs in one blade passage. Among the three configurations, the first configuration has greater impact on the end wall cross flow and flow deflection which resulted in enhanced numerical stall margin of 3.5% from baseline at design speed. The reasons for this numerical stall margin improvement are discussed in detail.

A New Design Concept of Highly-Loaded Axial Flow Compressor by Applying Boundary Layer Suction and 3D Blade Technique

2008 ◽  
Author(s):  
Xiaoqing Qiang ◽  
Songtao Wang ◽  
Weichun Lin ◽  
Zhongqi Wang
Keyword(s):  
Boundary Layer ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Boundary Layer Separation ◽  
Design Concept ◽  
Turning Angle ◽  
Boundary Layer Suction ◽  
Layer Separation ◽  
Flow Compressor ◽  
Highly Loaded

A new design concept of highly-loaded axial flow compressor by applying boundary layer suction and 3D blade technique was proposed in this paper. The basic idea of this design concept was that low reaction was adopted as while as increasing the rotor’s geometry turning angle, so that the boundary layer separation of a rotor could be eliminated and the rotor was kept working in high efficiency. This design concept would greatly increase the stator’s geometry turning angle, so boundary layer suction on stator cascades was adopted in order to restrain the boundary layer separation. In some situations, 3D blade technique was also applied in order to control the boundary layer separation more efficiently. The advantages of the above design concept were: the compressor’s pressure ratio was increased remarkably; boundary layer suction was only adopted in stator cascades so as to reduce the complexity of boundary layer suction structure. The key techniques of the new design concept were also explained in this paper. In order to increase the compressor’s pressure ratio, the geometry turning angle of rotor was increased greatly, and the rotor inlet was prewhirled to reduce the rotor’s reaction so as to restrain the rotor’s boundary separation. Boundary layer suction was carried out in the stator cascades (mainly on suction side), hub and shroud in order to control the flow separation. 3D blade technique could be adopted if necessary. The limitation of the application of this design concept was also pointed out through the analysis of the Mach number at rotor inlet, the prewhirl angle of rotor, the work distribution along span wise and the control method of stator separation. Numerical simulation was carried out on a single low-reaction compressor stage with IGV in order to demonstrate the new design concept. By using boundary layer suction and 3D blade technique, the energy loss in stator cascades was greatly reduced and the whole stage’s isentropic efficiency was about 90%. The low-reaction stage’s aerodynamic load was double than conventional design. The boundary layer separation could be effectively controlled by proper combination of boundary layer suction and bowed or twisted blade. The numerical result proved that the new design concept was feasible and had a wide application area.

Sign in / Sign up

Export Citation Format

Share Document