Effects of Free-Stream Turbulence Intensity and Frequency on Heat Transfer to Turbine Blading

1981 ◽  
Vol 103 (1) ◽  
pp. 60-64 ◽  
Author(s):  
F. J. Bayley ◽  
W. J. Priddy
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Free Stream ◽  
Turbine Blades ◽  
Theoretical Work ◽  
Experimental Program ◽  
Blade Surface ◽  
Free Stream Turbulence ◽  
Mainstream Flow ◽  
Turbine Blading

This paper describes a continuing experimental program in which the frequency and amplitude of turbulence in the mainstream flow over a cascade of turbine blades are separately and controllably varied. The effects of these two characteristics of the flow are demonstrated showing the significant effect of each upon the rates of convection to most of the blade surface. A correlation following the predictions of the theoretical work of reference [2] is shown to have some promise, although some modification is required to allow for changes in mainstream Reynolds number not accounted for by the usual normalizing procedure.

Correlations for the Prediction of Intermittency and Turbulent Spot Production Rate in Separated Flows

2018 ◽  
Author(s):  
M. Dellacasagrande ◽  
R. Guida ◽  
D. Lengani ◽  
D. Simoni ◽  
M. Ubaldi ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Production Rate ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Turbine Blades ◽  
Transition Process ◽  
Separated Flows ◽  
Intensity Level ◽  
Turbulent Spot ◽  
Free Stream Turbulence

Experimental data describing laminar separation bubbles developing under strong adverse pressure gradients, typical of Ultra-High-Lift turbine blades, have been analyzed to define empirical correlations able to predict the main features of the separated flow transition. Tests have been performed for three different Reynolds numbers and three different free-stream turbulence intensity levels. For each condition, around 4000 Particle Image Velocimetry (PIV) snapshots have been acquired. A wavelet based intermittency detection technique, able to identify the large scale vortices shed as a consequence of the separation, has been applied to the large amount of data to efficiently compute the intermittency function for the different conditions. The transition onset and end positions, as well as the turbulent spot production rate are evaluated. Thanks to the recent advancements in the understanding on the role played by Reynolds number and free-stream turbulence intensity on the dynamics leading to transition in separated flows, guest functions are proposed in the paper to fit the data. The proposed functions are able to mimic the effects of Reynolds number and free-stream turbulence intensity level on the receptivity process of the boundary layer in the attached part, on the disturbance exponential growth rate observed in the linear stability region of the separated shear layer, as well as on the nonlinear later stage of completing transition. Once identified the structure of the correlation functions, a fitting process with own and literature data allowed us to calibrate the unknown constants. Results reported in the paper show the ability of the proposed correlations to adequately predict the transition process in the case of separated flows. The correlation for the spot production rate here proposed extends the correlations proposed in liter-ature for attached (by-pass like) transition process, and could be used in γ–Reϑ codes, where the spot production rate appears as a source term in the intermittency function transport equation.

Numerical Approach at Flat Plate for Predicting the Film Cooling Effectiveness Part A: Effect Blowing Ratio

2018 ◽  
Vol 16 ◽  
pp. 30-44 ◽  
Author(s):  
Farouk Kebir ◽  
Azzeddine Khorsi
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Film Cooling ◽  
Thermal Stresses ◽  
Free Stream ◽  
Turbine Blades ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Blowing Ratio

Film cooling is vital for gas turbine blades to protect them from thermal stresses and high temperatures due to the hot gas flow in the blade surface. Film cooling is applied to almost all external surfaces associated with aerodynamic profiles that are exposed to hot combustion gases such as main bodies, end-walls, blade tips and leading edges. In a review of the literature, it was found that there are strong effects of free-stream turbulence, surface curvature and hole shape on film cooling performance also blowing ratio. The performance of the film cooling is difficult to predict due to the inherent complex flow fields along the surfaces of the airfoil components in the turbine engines. From all what we introducing the film cooling is reviewed through a discussion of the analyses methodologies, a physical description, and the various influences on film-cooling performance. Initially Computational analysis was done on a flat plate with hole inclined at 55° to the surface plate. This study focuses on the efficient computation of film cooling flows with three blowing ratio. The numerical results show the effectiveness cooling and heat transfer behavior with increasing injection blowing ratio M (0.5, 1, and 1.5). The influence of increased blade film cooling can be assessed via the values of Nusselt number in terms of reduced heat transfer to the blade. Predictions of film effectiveness are compared with experimental results for a circular jet at blowing ratios ranging from 0.5, 1.0 and 1.5. The present results are obtained at a free stream turbulence of 10%, which are the typical conditions upstream of the effectiveness is generally lower for a large stream-wise angle of 55°.

Simulation of Heat Transfer From Flow With High Free-Stream Turbulence to Turbine Blades

1997 ◽  
Vol 119 (2) ◽  
pp. 284-291 ◽  
Author(s):  
E. Fridman
Keyword(s):  
Heat Transfer ◽  
Free Stream ◽  
Turbine Blades ◽  
Plate Boundary ◽  
Transfer Coefficients ◽  
Relaxation Length ◽  
Free Stream Turbulence ◽  
Heat Transfer Coefficients ◽  
High Level ◽  
Flat Plate Boundary Layer

The present investigation is devoted to one of the most difficult problems in the gas turbine industry: predicting the heat transfer to turbine blades. It is known that one of the important factors that affects heat transfer coefficients is a significant level of turbulence in the flow that surrounds a turbine blade. The influence of free-stream turbulence on heat transfer coefficients for a flat plate boundary layer with zero pressure gradient or in the vicinity of the stagnation point of a circular cylinder is investigated numerically. An algebraic relaxation-length model of turbulence is applied in order to simulate real situations in flows with a high level of free-stream turbulence. The results, temperature and velocity profiles, and heat transfer and drag coefficients, are compared with available experimental data. The proposed method is recommended for practical calculations of heat transfer coefficients on turbine blades.

Free-Stream Turbulence Effects on Local Heat Transfer from a Sphere

1972 ◽  
Vol 94 (1) ◽  
pp. 7-14 ◽  
Author(s):  
L. B. Newman ◽  
E. M. Sparrow ◽  
E. R. G. Eckert
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Free Stream ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Flux Sensor ◽  
Forward Region ◽  
Number Range ◽  
Free Stream Turbulence

Experiments involving both heat-transfer and turbulence-field measurements were performed to determine the influence of free-stream turbulence on the local heat transfer from a sphere situated in a forced-convection airflow. The research was facilitated by a miniature heat-flux sensor which could be positioned at any circumferential location on the equator of the sphere. Turbulence grids were employed to generate free-stream turbulence with intensities of up to 9.4 percent. The Reynolds-number range of the experiments was from 20,000 to 62,000. The results indicate that the local heat flux in the forward region of the sphere is uninfluenced by free-stream turbulence levels of up to about 5 percent. For higher turbulence levels, the heat-flux increases with the turbulence intensity, the greatest heat-flux augmentation found here being about 15 percent. Furthermore, at the higher turbulence intensities, there appears to be a departure from the half-power Reynolds-number dependence of the stagnation-point Nusselt number. Turbulent separation occurred at Reynolds numbers of 42,000 and 62,000 for a turbulence level of 9.4 percent, these values being well below the transition Reynolds number of 2 × 105 for a sphere situated in a low-turbulence flow.

scholarly journals Recent Studies in Turbine Blade Cooling

2004 ◽  
Vol 10 (6) ◽  
pp. 443-457 ◽  
Author(s):  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Gas Turbines ◽  
Critical Role ◽  
Turbine Blades ◽  
Moment Closure ◽  
Image Method ◽  
Blade Surface ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence

Gas turbines are used extensively for aircraft propulsion, land-based power generation, and industrial applications. Developments in turbine cooling technology play a critical role in increasing the thermal efficiency and power output of advanced gas turbines. Gas turbine blades are cooled internally by passing the coolant through several rib-enhanced serpentine passages to remove heat conducted from the outside surface. External cooling of turbine blades by film cooling is achieved by injecting relatively cooler air from the internal coolant passages out of the blade surface in order to form a protective layer between the blade surface and hot gas-path flow. For internal cooling, this presentation focuses on the effect of rotation on rotor blade coolant passage heat transfer with rib turbulators and impinging jets. The computational flow and heat transfer results are also presented and compared to experimental data using the RANS method with various turbulence models such as k-ε, and second-moment closure models. This presentation includes unsteady high free-stream turbulence effects on film cooling performance with a discussion of detailed heat transfer coef- ficient and film-cooling effectiveness distributions for standard and shaped film-hole geometry using the newly developed transient liquid crystal image method.

Effects of Periodic Unsteadiness, Free-Stream Turbulence, and Flow Reynolds Number on Separation-Bubble Transition

2003 ◽  
Author(s):  
S. K. Roberts ◽  
M. I. Yaras
Keyword(s):  
Reynolds Number ◽  
Free Stream ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Separated Flow ◽  
Suction Side ◽  
Streamwise Velocity ◽  
Flow Transition ◽  
Free Stream Turbulence ◽  
Flow Reynolds Number

This paper presents measurements of the combined effects of free-stream turbulence and periodic streamwise velocity variations on separation-bubble transition. The measurements were performed on a flat plate at two values of flow Reynolds number, with a streamwise pressure distribution similar to those encountered on the suction side of axial turbine blades. The experiment was designed to facilitate independent control of turbulence and periodic velocity fluctuations in the free-stream. The free-stream turbulence intensity was varied from 0.4% to 4.5%, and the periodic unsteadiness corresponded to Strouhal numbers of 0.0, 2.4 and 4.0. Based on the results, the relative importance of free-stream turbulence and periodic unsteadiness on the streamwise locations of separation, transition and reattachment points are quantified. Existing mathematical models for predicting separated-flow transition and reattachment are then evaluated in this context.

Leading Edge Separation Bubbles on Turbomachine Blades

1995 ◽  
Vol 117 (1) ◽  
pp. 115-125 ◽  
Author(s):  
R. E. Walraevens ◽  
N. A. Cumpsty
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Free Stream ◽  
Turbine Blades ◽  
Leading Edge ◽  
Compressor Blades ◽  
Free Stream Turbulence ◽  
Pressure Distributions ◽  
Small Influence ◽  
Separation Bubbles

Results are presented for separation bubbles of the type that can form near the leading edges of thin compressor or turbine blades. These often occur when the incidence is such that the stagnation point is not on the nose of the aerofoil. Tests were carried out at low speed on a single aerofoil to simulate the range of conditions found on compressor blades. Both circular and elliptic shapes of leading edge were tested. Results are presented for a range of incidence, Reynolds number, and turbulence intensity and scale. The principal quantitative measurements presented are the pressure distributions in the leading edge and bubble region, as well as the boundary layer properties at a fixed distance downstream, where most of the flows had reattached. Reynolds number was found to have a comparatively small influence, but a raised level of free-stream turbulence has a striking effect, shortening or eliminating the bubble and increasing the magnitude of the suction spike. Increased free-stream turbulence also reduces the boundary layer thickness and shape parameter after the bubble. Some explanations of the processes are outlined.

Measurements and Prediction of Free-Stream Turbulence and Pressure-Gradient Effects on Attached-Flow Boundary-Layer Transition

2003 ◽  
Author(s):  
S. K. Roberts ◽  
M. I. Yaras
Keyword(s):  
Reynolds Number ◽  
Free Stream ◽  
Turbine Blades ◽  
Boundary Layer Transition ◽  
Pressure Gradients ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Flow Reynolds Number ◽  
Attached Flow ◽  
Transition Length

This paper presents measurements of free-stream turbulence, streamwise pressure gradients and flow Reynolds number effects on attached-flow transition. The measurements were performed on a flat plate, at free-stream turbulence intensities ranging from 0.5% to 9.0%, four Reynolds numbers, and several streamwise pressure distributions, including ones that are typical of the suction side pressures of axial turbine blades. Based on the results, the extent of upstream movement of transition location with free-stream turbulence, the changes in transition length with variations in the streamwise pressure gradients, and the sensitivity of these trends to flow Reynolds number are quantified. Interpretation of the measurements is based primarily on streamwise and cross-stream intermittency distributions extracted from the velocity traces of hot-wire traverses. The measured transition inception locations and transition lengths are used to evaluate mathematical models available in the published literature. A modification is proposed to a transition length model to improve the prediction of the streamwise intermittency distribution.

Sign in / Sign up

Export Citation Format

Share Document