Simulation of Heat Transfer From Flow With High Free-Stream Turbulence to Turbine Blades

1997 ◽  
Vol 119 (2) ◽  
pp. 284-291 ◽  
Author(s):  
E. Fridman
Keyword(s):  
Heat Transfer ◽  
Free Stream ◽  
Turbine Blades ◽  
Plate Boundary ◽  
Transfer Coefficients ◽  
Relaxation Length ◽  
Free Stream Turbulence ◽  
Heat Transfer Coefficients ◽  
High Level ◽  
Flat Plate Boundary Layer

The present investigation is devoted to one of the most difficult problems in the gas turbine industry: predicting the heat transfer to turbine blades. It is known that one of the important factors that affects heat transfer coefficients is a significant level of turbulence in the flow that surrounds a turbine blade. The influence of free-stream turbulence on heat transfer coefficients for a flat plate boundary layer with zero pressure gradient or in the vicinity of the stagnation point of a circular cylinder is investigated numerically. An algebraic relaxation-length model of turbulence is applied in order to simulate real situations in flows with a high level of free-stream turbulence. The results, temperature and velocity profiles, and heat transfer and drag coefficients, are compared with available experimental data. The proposed method is recommended for practical calculations of heat transfer coefficients on turbine blades.

The Influence of Free Stream Turbulence on the Local Heat Transfer From Cylinders

1960 ◽  
Vol 82 (2) ◽  
pp. 101-107 ◽  
Author(s):  
R. A. Seban
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Free Stream ◽  
Separated Flow ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Turbulent Intensity ◽  
Transfer Coefficients ◽  
Free Stream Turbulence ◽  
Heat Transfer Coefficients

Local heat-transfer coefficients and recovery factors are presented for three different cylinders in a two-dimensional subsonic air flow, with emphasis on the effect of screen-produced turbulence on these quantities. The increase in turbulent intensity so realized produced larger local heat-transfer coefficients, in a way dependent upon the location on the cylinders, through a direct increase in the heat transfer to the laminar boundary layer, through an earlier transition to turbulence, or through an alteration in the character of the separated flow. Alternatively, recovery factors were affected less, being invariant with respect to the turbulent intensity for attached boundary layer flow, but demonstrating large changes in those separated flow regions for which increased free stream turbulence produced substantial changes in the nature of the separated flow.

Calculation of Heat Transfer to Convection-Cooled Gas Turbine Blades

1985 ◽  
Vol 107 (3) ◽  
pp. 620-627 ◽  
Author(s):  
W. Rodi ◽  
G. Scheuerer
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Complex Nature ◽  
Surface Boundary ◽  
Transfer Coefficients ◽  
Free Stream Turbulence ◽  
Gas Turbine Blades ◽  
Heat Transfer Coefficients

A mathematical model is presented for calculating the external heat transfer coefficients around gas turbine blades. The model is based on a finite-difference procedure for solving the boundary-layer equations which describe the flow and temperature field around the blades. The effects of turbulence are simulated by a low-Reynolds number version of the k-ε turbulence model. This allows calculation of laminar and transitional zones and also the onset of transition. Applications of the calculation method are presented to turbine-blade situations which have recently been investigated experimentally. Predicted and measured heat transfer coefficients are compared and good agreement with the data is observed. This is true especially for the pressure-surface boundary layer which is of a rather complex nature because it remains in a transitional state over the full blade length. The influence of various flow phenomena like laminar-turbulent transition and of the boundary conditions (pressure gradient, free-stream turbulence) on the predicted heat transfer rates is discussed.

Combined Effect of Free-Stream Turbulence and Unsteady Wake on Heat Transfer Coefficients From a Gas Turbine Blade

1995 ◽  
Vol 117 (2) ◽  
pp. 296-302 ◽  
Author(s):  
L. Zhang ◽  
J.-C. Han
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Combined Effect ◽  
Transfer Coefficients ◽  
Free Stream Turbulence ◽  
Heat Transfer Coefficients ◽  
Unsteady Wake ◽  
Turbulence Grid

The combined effect of free-stream turbulence and unsteady wakes on turbine blade surface heat transfer was studied. The experiments used a five-blade linear cascade in a low-speed wind tunnel facility. A turbulence grid and spoked-wheel type wake generator produced the free-stream turbulence and unsteady wakes. The mainstream Reynolds numbers based on the cascade inlet mean velocity and blade chord length were 100,000, 200,000, and 300,000. Results show that the blade time-averaged heat transfer coefficient depends on the mean turbulence intensity, regardless of whether this mean turbulence intensity is from unsteady wake only, turbulence grid only, or a wake and grid combination. The higher mean turbulence promotes earlier boundary layer transition and causes much higher heat transfer coefficients on the suction surface. It also significantly enhances the heat transfer coefficients on the pressure surface. The unsteady wake greatly affects blade heat transfer for low oncoming free-stream turbulence; however, the wake effect diminishes for high oncoming turbulence. The free-stream turbulence also strongly affects blade heat transfer for a low wake passing frequency, but the oncoming turbulence effect diminishes for a high unsteady wake condition.

scholarly journals A Theory for Wake-Induced Transition

1989 ◽  
Author(s):  
R. E. Mayle ◽  
K. Dullenkopf
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbulent Flow ◽  
Flat Plate ◽  
Free Stream ◽  
Plate Boundary ◽  
Transition Model ◽  
Model Comparisons ◽  
Turbulent Wakes ◽  
Flat Plate Boundary Layer

A theory for transition from laminar to turbulent flow as the result of unsteady, periodic passing of turbulent wakes in the free stream is developed using Emmons’ transition model. Comparisons made to flat plate boundary layer measurements and airfoil heat transfer measurements confirm the theory.

scholarly journals Effect of Discrete Ribs on Heat Transfer and Friction Inside Narrow Rectangular Cross Section Cooling Passage of Gas Turbine Blade

2021 ◽  
Vol 10 (6) ◽  
pp. 192-209
Author(s):  
Karthik Krishnaswamy ◽  
◽  
Srikanth Salyan ◽  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Hydraulic Diameter ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Cooling Passage

The performance of a gas turbine during the service life can be enhanced by cooling the turbine blades efficiently. The objective of this study is to achieve high thermohydraulic performance (THP) inside a cooling passage of a turbine blade having aspect ratio (AR) 1:5 by using discrete W and V-shaped ribs. Hydraulic diameter (Dh) of the cooling passage is 50 mm. Ribs are positioned facing downstream with angle-of-attack (α) of 30° and 45° for discrete W-ribs and discerte V-ribs respectively. The rib profiles with rib height to hydraulic diameter ratio (e/Dh) or blockage ratio 0.06 and pitch (P) 36 mm are tested for Reynolds number (Re) range 30000-75000. Analysis reveals that, area averaged Nusselt numbers of the rib profiles are comparable, with maximum difference of 6% at Re 30000, which is within the limits of uncertainty. Variation of local heat transfer coefficients along the stream exhibited a saw tooth profile, with discrete W-ribs exhibiting higher variations. Along spanwise direction, discrete V-ribs showed larger variations. Maximum variation in local heat transfer coefficients is estimated to be 25%. For experimented Re range, friction loss for discrete W-ribs is higher than discrete-V ribs. Rib profiles exhibited superior heat transfer capabilities. The best Nu/Nuo achieved for discrete Vribs is 3.4 and discrete W-ribs is 3.6. In view of superior heat transfer capabilities, ribs can be deployed in cooling passages near the leading edge, where the temperatures are very high. The best THPo achieved is 3.2 for discrete V-ribs and 3 for discrete W-ribs at Re 30000. The ribs can also enhance the power-toweight ratio as they can produce high thermohydraulic performances for low blockage ratios.

Numerical Approach at Flat Plate for Predicting the Film Cooling Effectiveness Part A: Effect Blowing Ratio

2018 ◽  
Vol 16 ◽  
pp. 30-44 ◽  
Author(s):  
Farouk Kebir ◽  
Azzeddine Khorsi
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Film Cooling ◽  
Thermal Stresses ◽  
Free Stream ◽  
Turbine Blades ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Blowing Ratio

Film cooling is vital for gas turbine blades to protect them from thermal stresses and high temperatures due to the hot gas flow in the blade surface. Film cooling is applied to almost all external surfaces associated with aerodynamic profiles that are exposed to hot combustion gases such as main bodies, end-walls, blade tips and leading edges. In a review of the literature, it was found that there are strong effects of free-stream turbulence, surface curvature and hole shape on film cooling performance also blowing ratio. The performance of the film cooling is difficult to predict due to the inherent complex flow fields along the surfaces of the airfoil components in the turbine engines. From all what we introducing the film cooling is reviewed through a discussion of the analyses methodologies, a physical description, and the various influences on film-cooling performance. Initially Computational analysis was done on a flat plate with hole inclined at 55° to the surface plate. This study focuses on the efficient computation of film cooling flows with three blowing ratio. The numerical results show the effectiveness cooling and heat transfer behavior with increasing injection blowing ratio M (0.5, 1, and 1.5). The influence of increased blade film cooling can be assessed via the values of Nusselt number in terms of reduced heat transfer to the blade. Predictions of film effectiveness are compared with experimental results for a circular jet at blowing ratios ranging from 0.5, 1.0 and 1.5. The present results are obtained at a free stream turbulence of 10%, which are the typical conditions upstream of the effectiveness is generally lower for a large stream-wise angle of 55°.

Sign in / Sign up

Export Citation Format

Share Document