Experimental Study on Static and Dynamic Characteristics of Annular Plain Seals With Porous Materials

1998 ◽  
Vol 120 (2) ◽  
pp. 165-172 ◽  
Author(s):  
S. Kaneko ◽  
H. Kamei ◽  
Y. Yanagisawa ◽  
H. Kawahara
Keyword(s):  
Porous Materials ◽  
Flow Rate ◽  
Dynamic Characteristics ◽  
Reaction Force ◽  
Leakage Flow ◽  
Static And Dynamic Characteristics ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Leakage Flow Rate ◽  
Hydrostatic Force

Static and dynamic characteristics are experimentally investigated for annular plain seals with porous materials applied to the seal surface by insertion into the middle of the seal. Experimental results show that annular plain seals with porous materials have a higher leakage flow rate, larger main stiffness coefficients, and smaller cross-coupled stiffness coefficients and main damping coefficients than conventional annular plain seals with solid surfaces. In the porous seals, an increase of approximately 30 percent in the leakage flow rate and reduction of the same amount in the main damping coefficients are obtained, whereas the main stiffness coefficients for the porous seals are four to six times as much as those for the solid seals due to the increase in the hydrostatic force induced by a function of the hydrostatic porous bearing. This suggests that the quantitative effects of the porous materials on the main stiffness coefficients are much more significant than the effects on the leakage flow rate and the other dynamic coefficients. The larger main stiffness coefficients for the porous seals yield larger radial reaction force for a small concentric whirling motion, which would contribute to rotor stability from the viewpoint of increasing speed limits due to a stiffer rotor support.

Numerical and Experimental Analyses of Static and Dynamic Characteristics for Partially Helically Grooved Liquid Annular Seals

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Keisuke Nagai ◽  
Kazuki Koiso ◽  
Satoru Kaneko ◽  
Hiroo Taura ◽  
Yusuke Watanabe
Keyword(s):  
Flow Rate ◽  
Dynamic Characteristics ◽  
Smooth Surface ◽  
Reaction Force ◽  
Leakage Flow ◽  
Dynamic Reaction ◽  
Static And Dynamic Characteristics ◽  
Whirling Motion ◽  
Leakage Flow Rate ◽  
Experimental Analyses

Numerical and experimental analyses of the static and dynamic characteristics of the liquid annular seals with axially partial helical grooves were conducted to investigate the effects of the axial length gal of a helically grooved section in a seal stator. The numerical solution and experimental procedures were applied in the same manner as in previous studies on through-helically grooved seals, wherein the grooves extend across the seal length. The numerical results qualitatively agreed with the experimental results, demonstrating the validity of the numerical analysis. The leakage flow rate Q was lower in the partially helically grooved seals than that of conventional through-helically grooved seals across a small range of rotor spinning velocities. In contrast, the reduction in Q due to the pumping effect caused by the spin of the rotor diminished with the decrease in gal. For a small concentric whirling motion of the rotor, the radial dynamic reaction force Fr and magnitude of variation in the tangential dynamic reaction force Ft with the whirling angular velocity increased with the decrease in gal, and their values approached the corresponding values for the smooth-surface seal. Under the same rotor whirling velocity, the Ft for the partially helically grooved seals became lower than that for the smooth-surface seal (similar to the case for the through-helically grooved seal), although decreasing gal tended to increase Ft. These results suggest that partially helically grooved seals can improve the efficiency and stability margin of the pumps because of the reduction in leakage flow rate and suppression of the rotor forward whirling motion (with large radial and tangential dynamic reaction forces) as compared to conventional through-helically grooved seals.

Experimental Study on Static and Dynamic Characteristics of Liquid Annular Convergent-Tapered Damper Seals With Honeycomb Roughness Pattern

2003 ◽  
Vol 125 (3) ◽  
pp. 592-599 ◽  
Author(s):  
Satoru Kaneko ◽  
Takashi Ikeda ◽  
Takuro Saito ◽  
Shin Ito
Keyword(s):  
Dynamic Characteristics ◽  
Smooth Surface ◽  
Reaction Force ◽  
Static And Dynamic Characteristics ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Whirling Motion ◽  
Leakage Flow Rate ◽  
Annular Seal ◽  
Honeycomb Pattern

Honeycomb damper seals with convergent-tapered clearance have been proposed to improve static and dynamic characteristics of liquid annular seals employed in pumps. Their characteristics are experimentally investigated and compared to those for a conventional straight (no taper) annular seal with smooth surface and a straight damper seal with identical honeycomb pattern in seal stator. Three convergent-tapered honeycomb damper seals are used in the test, and have different inlet clearance (maximum clearance) and almost the same outlet clearance (minimum clearance). Their outlet clearance is almost the same as the clearance of the straight smooth seal and is slightly smaller than the clearance of the straight damper seal. Experimental results show that the convergent-tapered damper seals as well as the straight damper seal have lower leakage flow rate and cross-coupled stiffness coefficients, and larger main damping coefficients than the straight smooth seal, resulting in larger effective damping coefficients. These results are mainly due to surface roughness in the seal stator such as a honeycomb pattern used in the present analysis. The convergent-tapered damper seals also have larger main stiffness coefficients than the straight smooth and damper seals, which is mainly due to the convergent-tapered clearance and yields larger radial reaction force for a small concentric whirling motion. Consequently, the convergent-tapered damper seals have better seal characteristics than the conventional straight smooth seal and the straight damper seal with the same roughness pattern from the viewpoints of decreasing the leakage and improving the rotor stability capacity.

scholarly journals Impact of Orifice-to-Pipe Diameter Ratio on Leakage Flow: An Experimental Study

Water ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 2189
Author(s):  
Tingchao Yu ◽  
Xiangqiu Zhang ◽  
Iran E. Lima Neto ◽  
Tuqiao Zhang ◽  
Yu Shao ◽  
...  
Keyword(s):  
Experimental Study ◽  
Flow Rate ◽  
Pipe Wall ◽  
Pressure Head ◽  
Diameter Ratio ◽  
Pipe Diameter ◽  
Leakage Flow ◽  
Leakage Flow Rate ◽  
Different Shapes ◽  
Real Scale

The traditional orifice discharge formula used to estimate the flow rate through a leak opening at a pipe wall often produces inaccurate results. This paper reports an original experimental study in which the influence of orifice-to-pipe diameter ratio on leakage flow rate was investigated for several internal/external flow conditions and orifice holes with different shapes. The results revealed that orifice-to-pipe diameter ratio (or pipe wall curvature) indeed influenced the leakage flow, with the discharge coefficient ( C d ) presenting a wide variation (0.60–0.85). As the orifice-to-pipe diameter ratio decreased, the values of C d systematically decreased from about 12% to 3%. Overall, the values of C d also decreased with β (ratio of pressure head differential at the orifice to wall thickness), as observed in previous studies. On the other hand, orifice shape, main pipe flow velocity, and external medium (water or air) all had a secondary effect on C d . The results obtained in the present study not only demonstrated that orifice-to-pipe diameter ratio affects the outflow, but also that real scale pipes may exhibit a relevant deviation of C d from the classical range (0.61–0.67) reported in the literature.

scholarly journals Experimental Study on Static and Dynamic Characteristics of Annular Plain Seals With Porous Materials.

1997 ◽  
Vol 63 (605) ◽  
pp. 1-9
Author(s):  
Satoru KANEKO ◽  
Hideharu KAMEI ◽  
Yukinobu YANAGISAWA ◽  
Hideo KAWAHARA ◽  
Nobutaka YAMAGUCHI
Keyword(s):  
Experimental Study ◽  
Porous Materials ◽  
Dynamic Characteristics ◽  
Static And Dynamic Characteristics

scholarly journals Effect of hydraulic and geometric factors upon leakage flow rate in pressurized pipes

RBRH ◽  
2021 ◽  
Vol 26 ◽  
Author(s):  
Mayara Francisca da Silva ◽  
Fábio Veríssimo Gonçalves ◽  
Johannes Gérson Janzen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Leakage Flow ◽  
Cfd Simulations ◽  
Mean Velocity ◽  
Leakage Flow Rate ◽  
Geometric Factors ◽  
Leakage Area ◽  
Computational Fluid Dynamics Cfd

ABSTRACT Computational Fluid Dynamics (CFD) simulations of a leakage in a pressurized pipe were undertaken to determine the empirical effects of hydraulic and geometric factors on the leakage flow rate. The results showed that pressure, leakage area and leakage form, influenced the leakage flow rate significantly, while pipe thickness and mean velocity did not influence the leakage flow rate. With relation to the interactions, the effect of pressure upon leakage flow rate depends on leakage area, being stronger for great leakage areas; the effects of leakage area and pressure on leakage flow rate is more pronounced for longitudinal leakages than for circular leakages. Finally, our results suggest that the equations that predict leakage flow rate in pressurized pipes may need a revision.

scholarly journals Leakage Characteristic Identification of Labyrinth Seals on Reciprocating Piston through Transient Simulations

2019 ◽  
Vol 2019 ◽  
pp. 1-12
Author(s):  
Lingzi Wang ◽  
Jianmei Feng ◽  
Mingfeng Wang ◽  
Zenghui Ma ◽  
Xueyuan Peng
Keyword(s):  
Flow Rate ◽  
Pressure Ratio ◽  
Piston Compressor ◽  
Pressure Change ◽  
Labyrinth Seal ◽  
Relative Molecular Mass ◽  
Geometrical Parameters ◽  
Leakage Flow ◽  
Reciprocating Motion ◽  
Leakage Flow Rate

In the reciprocating labyrinth piston compressor, the characteristic of the internal leakage is crucial for the leakage management and performance improvement of the compressor. However, most of the published studies investigated the rotor-stator system, and those who study the reciprocating piston-cylinder system basically focus on the effects of the geometrical parameters. These conclusions could not directly be applied to predict the real-time leakage flow rate through the labyrinth seal because of the fast reciprocating motion of the piston, which will cause continually pressure change in two compression chambers, and then the pressure fluctuation will affect the flow through the labyrinth seal. A transient simulation model employing the multiscale dynamic mesh, which considers the effect of the reciprocating motion of the piston in the cylinder, is established to identify the characteristics of the internal leakage. This model was verified by a specially designed compressor, and the influence of various parameters was analyzed in detail. The sealing performance decreased linearly with the increase in the pressure ratio, and higher pressure inlet leads to higher leakage flow under the same pressure ratio. The labyrinth seal performance positively correlated to the increase of the rotational speed. Leakage characteristics of five working mediums were carried out, and the results indicated that the relative leakage decreased with an increase in the relative molecular mass. From this study, the realistic internal leakage flow rate under different operating parameters in the reciprocating labyrinth piston compressor could be predicated.

Analysis on the Side Leakage Amount of the Friction between Piston and Cylinder Block in Axial Piston Pump

2014 ◽  
Vol 635-637 ◽  
pp. 341-345 ◽  
Author(s):  
Wei Wang
Keyword(s):  
Flow Rate ◽  
Piston Pump ◽  
Cylinder Block ◽  
Correction Coefficient ◽  
Leakage Flow ◽  
Fluid Viscosity ◽  
Axial Piston Pump ◽  
Viscosity Change ◽  
Leakage Flow Rate ◽  
Axial Piston

The spherical distribution pairs of the plunger and the cylinder friction, has an important influence on the performance of spherical port plate axial piston pump. Based on the analysis of fluid viscosity change with pressure and temperature, considering friction differential pressure flow and shear flow, establishes the mathematics model of the friction pair of leakage. The simulation analysis using MATLAB software, the leakage flow rate is not proportional to pressure, but with the increase of pressure leakage flow was increased, and with the increase of pressure viscosity coefficient and temperature coefficient of viscosity, the leakage flow rate correction coefficient increases obviously, so in the choice of the hydraulic oil cylinder hole, should choose a relatively moving average leakage rate had no effect the piston ring slot.

Analysis of Static Characteristics of Pressure Seal in Actual High Pressure Pump

2011 ◽  
Author(s):  
Isao Hagiya ◽  
Katsutoshi Kobayashi ◽  
Yoshimasa Chiba ◽  
Tetsuya Yoshida ◽  
Akira Arai
Keyword(s):  
High Pressure ◽  
Flow Rate ◽  
High Speed ◽  
Control Volume ◽  
Leakage Flow ◽  
High Pressure Pump ◽  
Flow Rates ◽  
Leakage Flow Rate ◽  
Rotor Dynamic ◽  
Pressure Seal

We predicted the leakage flow rates of a pressure seal in an actual high-pressure multistage pump. Since the pressure of the actual pump is higher than that of a model pump, accurate prediction of leakage flow rate and rotor dynamic forces for an actual pump is more difficult than that for a model pump. A non-contacting seal is used as a pressure seal to suppress leakage flow for high-pressure multistage pumps. When such pumps are operated at high speed, the fluid force acting on an eccentric rotor may cause vibration instability. For vibration stability analysis, we need to estimate static and dynamic characteristics of the pressure seals, i.e., leakage flow rate and rotor dynamic coefficients. We calculated the characteristics of the pressure seal based on Iwatsubo group’s method. The pressure seal we developed has labyrinth geometry consisting of grooves with different sizes. This method numerically calculates the characteristics of the grooved seal by using a three-control-volume model and a perturbation method. We compared the calculated and measured leakage flow rates. We found that the calculated results quantitatively agreed with the measured one in the actual pump and the characteristics of pressure and velocity for the seal with non-uniform-sized grooves were clarified.

Sign in / Sign up

Export Citation Format

Share Document