Simultaneous Measurement of Surface Topography and Friction Force by a Single-Head Lateral Force Microscope

1995 ◽  
Vol 117 (2) ◽  
pp. 334-340 ◽  
Author(s):  
C.-J. Lu ◽  
Zhaoguo Jiang ◽  
D. B. Bogy ◽  
T. Miyamoto
Keyword(s):  
Friction Coefficient ◽  
Surface Topography ◽  
Friction Force ◽  
Rotation Angle ◽  
Point Contact ◽  
Lateral Force ◽  
Wear Depth ◽  
Optical Head ◽  
Lateral Force Microscope ◽  
Normal Deflection

Although friction force measurements using one sensor to detect both the normal deflection and rotation angle of a scanning probe are convenient and popular, the critical issues regarding the calibration of the instruments have not been fully studied. A Lateral Force Microscope (LFM), modified from the Point Contact Microscope (PCM), is used to simultaneously measure the surface topography and friction force. An optical head is used to measure the normal bending deflection and rotation angle of the cantilever that carries the diamond tip. Emphasis is put on the development of reliable calibration procedures for obtaining the normal deflection and rotation sensitivities of the optical head as well as the spring constants in the bending and torsion modes. The friction loop, which is essential for friction measurements, is investigated in detail. The LFM is used to measure a two-phase composite to show its ability to distinguish different materials on a surface. Wear tests on a single-crystal silicon <100> surface show different friction coefficient regimes, depending on the applied load. For small loads, there is no wear and the friction coefficient is constant. For larger loads, the friction coefficient and wear depth increase with normal load.

scholarly journals Estimation of Wear Resistance for Multilayer Coatings Obtained by Nitrogenchroming

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1153
Author(s):  
Ivan Pavlenko ◽  
Jozef Zajac ◽  
Nadiia Kharchenko ◽  
Ján Duplák ◽  
Vitalii Ivanov ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Spectral Analysis ◽  
Friction Coefficient ◽  
Cutting Tools ◽  
Wear Intensity ◽  
Maximum Amount ◽  
Multilayer Coatings ◽  
Wear Depth ◽  
X Ray ◽  
Machine Parts

This article deals with improving the wear resistance of multilayer coatings as a fundamental problem in metal surface treatment, strengthening elements of cutting tools, and ensuring the reliability of machine parts. It aims to evaluate the wear depth for multilayer coatings by the mass loss distribution in layers. The article’s primary purpose is to develop a mathematical method for assessing the value of wear for multilayer steel-based coatings. The study material is a multilayer coating applied to steel DIN C80W1. The research was performed using up-to-date laboratory equipment. Nitrogenchroming has been realized under overpressure in two successive stages: nitriding for 36 h at temperature 540 °C and chromizing during 4 h at temperature 1050 °C. The complex analysis included several options: X-ray phase analysis, local micro-X-ray spectral analysis, durometric analysis, and determination of wear resistance. These analyses showed that after nitrogenchroming, the three-layer protective coating from Cr23C6, Cr7C3, and Cr2N was formed on the steel surface. Spectral analysis indicated that the maximum amount of chromium 92.2% is in the first layer from Cr23C6. The maximum amount of carbon 8.9% characterizes the layer from Cr7C3. Nitrogen is concentrated mainly in the Cr2N layer, and its maximum amount is 9.4%. Additionally, it was determined that the minimum wear is typical for steel DIN C80W1 after nitrogenchroming. The weight loss of steel samples by 25 mg was obtained. This value differs by 3.6% from the results evaluated analytically using the developed mathematical model of wear of multilayer coatings after complex metallization of steel DIN C80W1. As a result, the impact of the loading mode on the wear intensity of steel was established. As the loading time increases, the friction coefficient of the coated samples decreases. Among the studied samples, plates from steel DIN C80W1 have the lowest friction coefficient after nitrogenchroming. Additionally, a linear dependence of the mass losses on the wearing time was obtained for carbide and nitride coatings. Finally, an increase in loading time leads to an increase in the wear intensity of steels after nitrogenchroming. The achieved scientific results are applicable in developing methods of chemical-thermal treatment, improving the wear resistance of multilayer coatings, and strengthening highly loaded machine parts and cutting tools.

scholarly journals Comparison between multi-walled carbon nanotubes and titanium dioxide nanoparticles as additives on performance of turbine meter oil nano lubricant

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Hadi Pourpasha ◽  
Saeed Zeinali Heris ◽  
Yaghob Mohammadfam
Keyword(s):  
Carbon Nanotubes ◽  
Titanium Dioxide ◽  
Friction Coefficient ◽  
Pressure Drop ◽  
Mass Fraction ◽  
Viscosity Index ◽  
Wear Depth ◽  
Nano Lubricant ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

AbstractThis research aims of compare the impact of the mass fraction of multi-walled carbon nanotubes (MWCNTs) and titanium dioxide (TiO2) nano additive on the tribological and thermophysical attributes of turbine meter oil. These attributes include the average friction coefficient, pressure drop, wear, flash point, pour point, relative viscosity, kinematics viscosity, and viscosity index. The pressure drops and the average friction coefficient inside the copper tube were simulated and compared with experimental results. In this study, for the synthesis of nano lubricants from turbine meter oil as a pure fluid and from MWCNTs and TiO2 as nano additives in the mass fraction of 0.05, 0.1, 0.2, 0.3, and 0.4 wt.% and from oleic acid and Triton x100 as surfactants were utilized. The results illustrated that the wear depth of copper pins in the presence of nano lubricant with 0.4 wt.% of MWCNTs and 0.1 wt.% TiO2 was improved by 88.26% and 71.43%, respectively. Increasing 0.3 wt.% of TiO2 and MWCNTs into the oil caused to improvement in viscosity index. The simulation data and experimental data for the pressure drop were closer together and indicated a minor error that the maximum error is less than 10%.

Effect of shape/size and distribution of microgeometries of textures on tribo-performance of crankpin bearing

2021 ◽  
pp. 135065012110105
Author(s):  
Nguyen Van Liem ◽  
Wu Zhenpeng ◽  
Jiao Renqiang
Keyword(s):  
Friction Coefficient ◽  
Friction Force ◽  
Contact Force ◽  
Distribution Density ◽  
Hydrodynamic Lubrication ◽  
Operating Conditions ◽  
Asperity Contact ◽  
Combined Model ◽  
Obvious Effect ◽  
Area Density

The effect of the shape/size and distribution of microgeometries of textures on improving the tribo-performance of crankpin bearing is proposed. Based on a combined model of the slider-crank mechanism dynamic and hydrodynamic lubrication, the distribution density, area density, and shape of spherical textures, square-cylindrical textures, wedge-shaped textures, and a hybrid between spherical texture and square-cylindrical texture on the crankpin bearing's tribo-performance are investigated under different operating conditions of the engine. The tribological characteristic of the crankpin bearing is then evaluated via the indexes of the oil film pressure p, asperity contact force, friction force, and friction coefficient of the crankpin bearing. The research results show that the distribution density with n = 12 and m = 6, and area density with α = 30% of various microtextures have an obvious effect on ameliorating the crankpin bearings tribo-performance. Concurrently, at the mixed lubrication region, the shape of the square-cylindrical texture on improving the tribo-performance is better than the other shapes of the spherical texture, wedge-shaped texture, and spherical and square-cylindrical texture. Particularly, all the average values of the asperity contact force, friction force, and friction coefficient with a square-cylindrical texture are significantly reduced by 14.6%, 19.5%, and 34.5%, respectively, in comparison without microtextures. Therefore, the microtextures of the spherical texture applied on the bearing surface can contribute to enhance the durability and decrease the friction power loss of the engine.

A novel technique for modeling friction behavior in knitted fabric simulation

2017 ◽  
Vol 29 (6) ◽  
pp. 776-792
Author(s):  
Vajiha Mozafary ◽  
Pedram Payvandy
Keyword(s):  
Friction Coefficient ◽  
Uniform Distribution ◽  
Friction Force ◽  
Experimental Result ◽  
Knitted Fabric ◽  
Friction Behavior ◽  
Content Type ◽  
Novel Technique ◽  
Fabric Structure ◽  
Fabric Surface

Purpose Fabric-object friction force is a fundamental factor in cloth simulation. A large number of parameters influence the frictional properties of fabrics such as fabric structure, yarn structure, and inherent properties of component fibers. The purpose of this paper is to propose a novel technique for modeling fabric-object friction force in knitted fabric simulation based on the mass spring model. Design/methodology/approach In this technique, unlike other studies, distribution of friction coefficient over the fabric surface is not uniform and depends on the fabric structure. The main reason for considering non-uniform distribution is that in various segments of fabric, contact percent of fabric-object is different. Findings The proposed technique and common methods based on friction coefficient uniform distribution are used to simulate the frictional behavior of knitted fabrics. The results show that simulation error values for proposed technique and common methods are 2.7 and 9.4 percent as compared with the experimental result, respectively. Originality/value In the existing methods of the friction force modeling, the friction coefficient of fabric is assumed uniform. But this assumption is not correct because fabric does not have an isotropic structure. Thus in this study, the friction coefficient distribution is considered based on fabric structure to achieve more of realistic simulations.

scholarly journals A thermal resistances-based approach for thermal-elastohydrodynamic calculations in point contacts

2017 ◽  
Vol 232 (11) ◽  
pp. 2088-2102 ◽  
Author(s):  
Eduardo de la Guerra Ochoa ◽  
Javier Echávarri Otero ◽  
Enrique Chacón Tanarro ◽  
Benito del Río López
Keyword(s):  
Friction Coefficient ◽  
Film Thickness ◽  
Thermal Effects ◽  
Good Accuracy ◽  
Computational Cost ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Point Contacts ◽  
New Approach ◽  
Ball On Disc

This article presents a thermal resistances-based approach for solving the thermal-elastohydrodynamic lubrication problem in point contact, taking the lubricant rheology into account. The friction coefficient in the contact is estimated, along with the distribution of both film thickness and temperature. A commercial tribometer is used in order to measure the friction coefficient at a ball-on-disc point contact lubricated with a polyalphaolefin base. These data and other experimental results available in the bibliography are compared to those obtained by using the proposed methodology, and thermal effects are analysed. The new approach shows good accuracy for predicting the friction coefficient and requires less computational cost than full thermal-elastohydrodynamic simulations.

Predicting the wear coefficient and friction coefficient in dry point contact using continuum damage mechanics

2018 ◽  
Vol 233 (3) ◽  
pp. 447-455 ◽  
Author(s):  
Sahar Ghatrehsamani ◽  
Saleh Akbarzadeh
Keyword(s):  
Friction Coefficient ◽  
Damage Mechanics ◽  
Point Contact ◽  
Continuum Damage Mechanics ◽  
Continuum Damage ◽  
Wear Coefficient ◽  
Mechanics Model ◽  
Pin On Disk ◽  
Disk Test ◽  
The Continuum

Wear coefficient and friction coefficient are two of the key parameters in the performance of any tribo-system. The main purpose of the present research is to use continuum damage mechanics to predict wear coefficient. Thus, a contact model is utilized that can be used to obtain the friction coefficient between the contacting surfaces. By applying this model to the continuum damage mechanics model, the wear coefficient between dry surfaces is predicted. One of the advantages of using this model is that the wear coefficient can be numerically predicted unlike other methods which highly rely on experimental data. In order to verify the results predicted by this model, tests were performed using pin-on-disk test rig for several ST37 samples. The results indicated that the wear coefficient increases with increasing the friction coefficient.

Sign in / Sign up

Export Citation Format

Share Document