Heat Transfer in Turbulent Boundary Layers Subjected to Free-Stream Turbulence—Part I: Experimental Results

2003 ◽  
Vol 125 (2) ◽  
pp. 232-241 ◽  
Author(s):  
Michael J. Barrett ◽  
D. Keith Hollingsworth
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Boundary Layers ◽  
Free Stream ◽  
Turbulent Boundary Layers ◽  
Small Scale ◽  
Length Scale ◽  
Momentum Thickness ◽  
Free Stream Turbulence

Turbulent boundary layers were subjected to grid-generated free-stream turbulence to study the effects of length scale and intensity on heat transfer. Relative to conventional boundary layer thickness measures, test conditions included very small-scale free-stream turbulence. The boundary layers studied ranged from 400–2700 in momentum-thickness Reynolds number and from 450–1900 in enthalpy-thickness Reynolds number. Free-stream turbulence intensities varied from 0.1–8.0%. Ratios of free-stream length scale to boundary-layer momentum thickness ranged from 4.4–32.5. The turbulent-to-viscous length-scale ratios presented are the smallest found in the heat-transfer literature; the ratios spanned from 115–1020. The turbulent-to-thermal ratios (using enthalpy thickness as the thermal scale) are also the smallest reported; the ratios ranged from 3.2–12.3. Relative to clean-free-stream expectations based on the momentum- and enthalpy-thickness Reynolds numbers, the skin friction coefficient increased by up to 16%, and the Stanton number increased by up to 46%.

Heat Transfer In Turbulent Boundary Layers Subjected to Free-Stream Turbulence—Part II: Analysis and Correlation

2003 ◽  
Vol 125 (2) ◽  
pp. 242-251 ◽  
Author(s):  
Michael J. Barrett ◽  
D. Keith Hollingsworth
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Boundary Layers ◽  
Free Stream ◽  
Turbulent Boundary Layers ◽  
Stanton Number ◽  
Length Scale ◽  
Free Stream Turbulence ◽  
New Correlation ◽  
Near Wall

A new heat transfer correlation for turbulent boundary layers subjected to free-stream turbulence was developed. The new correlation estimates dimensionless heat transfer coefficients without the use of conventional boundary-layer thickness measures and the associated Reynolds numbers. Using only free-stream parameters (mean velocity, turbulence intensity and length scale), the new correlation collected many authors’ elevated-turbulence, flat-plate Stanton number data to within ±11%. The level of scatter around the new correlation compared well to previous correlations that require additional flow information as input parameters. For a common subset of data, scatter using earlier correlation methods ranged from 5–10%; scatter around the new correlation varied from 6–9% over the same data subset. A length-scale dependence was identified in a Stanton number previously defined using a near-wall streamwise velocity fluctuation, St′. A new near-wall Stanton number was introduced; this parameter was regarded as a constant in a two-region boundary layer model on which the new correlation is based.

Aero-optics of subsonic turbulent boundary layers

2012 ◽  
Vol 696 ◽  
pp. 122-151 ◽  
Author(s):  
Kan Wang ◽  
Meng Wang
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Boundary Layers ◽  
Dominant Role ◽  
Elevation Angle ◽  
Turbulent Boundary Layers ◽  
Density Field ◽  
Small Scale ◽  
Number Range ◽  
Scale Turbulence

AbstractCompressible large-eddy simulations are carried out to study the aero-optical distortions caused by Mach 0.5 flat-plate turbulent boundary layers at Reynolds numbers of ${\mathit{Re}}_{\theta } = 875$, 1770 and 3550, based on momentum thickness. The fluctuations of refractive index are calculated from the density field, and wavefront distortions of an optical beam traversing the boundary layer are computed based on geometric optics. The effects of aperture size, small-scale turbulence, different flow regions and beam elevation angle are examined and the underlying flow physics is analysed. It is found that the level of optical distortion decreases with increasing Reynolds number within the Reynolds-number range considered. The contributions from the viscous sublayer and buffer layer are small, while the wake region plays a dominant role, followed by the logarithmic layer. By low-pass filtering the fluctuating density field, it is shown that small-scale turbulence is optically inactive. Consistent with previous experimental findings, the distortion magnitude is dependent on the propagation direction due to anisotropy of the boundary-layer vortical structures. Density correlations and length scales are analysed to understand the elevation-angle dependence and its relation to turbulence structures. The applicability of Sutton’s linking equation to boundary-layer flows is examined, and excellent agreement between linking equation predictions and directly integrated distortions is obtained when the density length scale is appropriately defined.

Pressure gradient effects on the large-scale structure of turbulent boundary layers

2013 ◽  
Vol 715 ◽  
pp. 477-498 ◽  
Author(s):  
Zambri Harun ◽  
Jason P. Monty ◽  
Romain Mathis ◽  
Ivan Marusic
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Amplitude Modulation ◽  
Large Scale ◽  
Outer Region ◽  
Adverse Pressure Gradient ◽  
Turbulent Boundary Layers ◽  
Small Scale

AbstractResearch into high-Reynolds-number turbulent boundary layers in recent years has brought about a renewed interest in the larger-scale structures. It is now known that these structures emerge more prominently in the outer region not only due to increased Reynolds number (Metzger & Klewicki, Phys. Fluids, vol. 13(3), 2001, pp. 692–701; Hutchins & Marusic, J. Fluid Mech., vol. 579, 2007, pp. 1–28), but also when a boundary layer is exposed to an adverse pressure gradient (Bradshaw, J. Fluid Mech., vol. 29, 1967, pp. 625–645; Lee & Sung, J. Fluid Mech., vol. 639, 2009, pp. 101–131). The latter case has not received as much attention in the literature. As such, this work investigates the modification of the large-scale features of boundary layers subjected to zero, adverse and favourable pressure gradients. It is first shown that the mean velocities, turbulence intensities and turbulence production are significantly different in the outer region across the three cases. Spectral and scale decomposition analyses confirm that the large scales are more energized throughout the entire adverse pressure gradient boundary layer, especially in the outer region. Although more energetic, there is a similar spectral distribution of energy in the wake region, implying the geometrical structure of the outer layer remains universal in all cases. Comparisons are also made of the amplitude modulation of small scales by the large-scale motions for the three pressure gradient cases. The wall-normal location of the zero-crossing of small-scale amplitude modulation is found to increase with increasing pressure gradient, yet this location continues to coincide with the large-scale energetic peak wall-normal location (as has been observed in zero pressure gradient boundary layers). The amplitude modulation effect is found to increase as pressure gradient is increased from favourable to adverse.

scholarly journals Interactions of large-scale free-stream turbulence with turbulent boundary layers

2016 ◽  
Vol 802 ◽  
pp. 79-107 ◽  
Author(s):  
Eda Dogan ◽  
Ronald E. Hanson ◽  
Bharathram Ganapathisubramani
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Large Scale ◽  
Free Stream ◽  
Turbulent Boundary Layers ◽  
Scale Interactions ◽  
Free Stream Turbulence ◽  
Small Scales ◽  
Near Wall

The scale interactions occurring within a turbulent boundary layer are investigated in the presence of free-stream turbulence. The free-stream turbulence is generated by an active grid. The free stream is monitored by a single-component hot-wire probe, while a second probe is roved across the height of the boundary layer at the same streamwise location. Large-scale structures occurring in the free stream are shown to penetrate the boundary layer and increase the streamwise velocity fluctuations throughout. It is speculated that, depending on the extent of the penetration, i.e. based on the level of free-stream turbulence, the near-wall turbulence production peaks at different wall-normal locations than the expected location of $y^{+}\approx 15$ for a canonical turbulent boundary layer. It is shown that the large scales dominating the log region have a modulating effect on the small scales in the near-wall region; this effect becomes more significant with increasing turbulence in the free stream, i.e. similarly increasing $Re_{\unicode[STIX]{x1D706}_{0}}$. This modulating interaction and its Reynolds-number trend have similarities with canonical turbulent boundary layers at high Reynolds numbers where the interaction between the large scales and the envelope of the small scales exhibits a pure amplitude modulation (Hutchins & Marusic, Phil. Trans. R. Soc. Lond. A, vol. 365 (1852), 2007, pp. 647–664; Mathis et al., J. Fluid Mech., vol. 628, 2009, pp. 311–337). This similarity has encouraging implications towards generalising scale interactions in turbulent boundary layers.

Effect of Free-Stream Turbulence on Heat Transfer through a Turbulent Boundary Layer

1978 ◽  
Vol 100 (4) ◽  
pp. 671-677 ◽  
Author(s):  
J. C. Simonich ◽  
P. Bradshaw
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Skin Friction Coefficient ◽  
Reynolds Analogy ◽  
Low Reynolds Numbers ◽  
Free Stream Turbulence ◽  
High Reynolds

Measurements in a boundary layer in zero pressure gradient show that the effect of grid-generated free-stream turbulence is to increase heat transfer by about five percent for each one percent rms increase of the longitudinal intensity. In fact, even a Reynolds analogy factor, 2 × (Stanton number)/(skin-friction coefficient), increases significantly. It is suggested that the irreconcilable differences between previous measurements are attributable mainly to the low Reynolds numbers of most of those measurements. The present measurements attained a momentum-thickness Reynolds number of 6500 (chord Reynolds number approximately 6.3 × 106) and are thought to be typical of high-Reynolds-number flows.

Calculation of Transitional Boundary Layers With an Improved Low-Reynolds-Number Version of the k–ε Turbulence Model

1994 ◽  
Vol 116 (4) ◽  
pp. 765-773 ◽  
Author(s):  
D. Biswas ◽  
Y. Fukuyama
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Boundary Layers ◽  
Turbulent Flows ◽  
Free Stream ◽  
Low Reynolds Number ◽  
Turbine Rotor ◽  
Limiting Behavior ◽  
Free Stream Turbulence ◽  
Low Reynolds

Several well-known low-Reynolds-number versions of the k–ε models are analyzed critically for laminar to turbulent transitional flows as well as near-wall turbulent flows from a theoretical and numerical standpoint. After examining apparent problems associated with the modeling of low-Reynolds-number wall damping functions used in these models, an improved version of the k–ε model is proposed by defining the wall damping factors as a function of some quantity (turbulence Reynolds number Ret) that is only a rather general indicator of the degree of turbulent activity at any location in the flow rather than a specific function of the location itself, and by considering the wall limiting behavior, the free-stream asymptotic behavior, and the balance between production and destruction of turbulence. This new model is applied to the prediction of (1) transitional boundary layers influenced by the free-stream turbulence, pressure gradient, and heat transfer; (2) external heat transfer distribution on the gas turbine rotor and stator blade under different inlet Reynolds number and free-stream turbulence conditions. It is demonstrated that the present model yields improved predictions.

scholarly journals The Turbulence That Matters

1997 ◽  
Author(s):  
R. E. Mayle ◽  
K. Dullenkopf ◽  
A. Schulz
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Gas Turbines ◽  
Free Stream ◽  
Transitional Flow ◽  
Stream Velocity ◽  
Length Scale ◽  
Effective Frequency ◽  
Large Wave ◽  
Free Stream Turbulence

A unified expression for the spectrum of turbulence is developed by asymptotically matching known expressions for small and large wave numbers, and a formula for the one-dimensional spectral function which depends on the turbulence Reynolds number Reλ is provided. In addition, formulas relating all the length scales of turbulence are provided. These relations also depend on Reynolds number. The effects of free-stream turbulence on laminar heat transfer and pre-transitional flow in gas turbines are re-examined in light of these new expressions using our recent thoughts on an ‘effective’ frequency of turbulence and an ‘effective’ turbulence level. The results of this are that the frequency most effective for laminar heat transfer is about 1.3U/Le, where U is the free-stream velocity and Le is the length scale of the eddies containing the most turbulent energy, and the most effective frequency for producing pre-transitional boundary layer fluctuations is about 0.3U/η where η is Kolmogorov’s length scale. In addition, the role of turbulence Reynolds number on stagnation heat transfer and transition is discussed, and new expressions to account for its effect are provided.

scholarly journals Calculation of Transitional Boundary Layers With an Improved Low-Reynolds Number Version of the k-ε Turbulence Model

1993 ◽  
Author(s):  
Debsish Biswas ◽  
Yoshitaka Fukuyama
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Boundary Layers ◽  
Turbulent Flows ◽  
Free Stream ◽  
Low Reynolds Number ◽  
Turbine Rotor ◽  
Limiting Behavior ◽  
Free Stream Turbulence ◽  
Low Reynolds

Several well known low-Reynolds version of the k-ε models are analyzed critically for laminar to turbulent transtional flows as well as near wall turbulent flows from theoretical and numerical standpoint. After examining apparent problems associated with the modelling of low-Reynolds number wall damping functions used in these models, an improved version of k-ε model is proposed by defining the wall damping factors as a function of some quantity (turbulence Reynolds number Rt) which is only a rather general indicator of the degree of turbulent activity at any location in the flow rather than a specific function of the location itself, and by considering the wall limiting behavior, the free-stream asyptotic behavior, and the balnce between production and destruction of turbulence. This new model is applied to the prediction of 1) transitional boundary layers influenced by the free-stream turbulence, pressure gradient and heat transfer; 2) external heat transfer distribution on the gas turbine rotor and stator blade under different inlet Reynolds number and free-stream turbulence conditions. It is demonstrated that the present model yield improved predictions.

Development of a Large-Scale Wind Tunnel for the Simulation of Turbomachinery Airfoil Boundary Layers

1981 ◽  
Vol 103 (4) ◽  
pp. 678-687 ◽  
Author(s):  
M. F. Blair ◽  
D. A. Bailey ◽  
R. H. Schlinker
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Wind Tunnel ◽  
Boundary Layers ◽  
Test Section ◽  
Large Scale ◽  
Free Stream ◽  
Two Dimensional ◽  
Transfer Data ◽  
Free Stream Turbulence

The procedures employed for the design of a closed-circuit, boundary layer wind tunnel are described. The tunnel was designed for the generation of large-scale, two-dimensional boundary layers on a heated flat surface with Reynolds numbers, pressure gradients, and free-stream turbulence levels typical of turbomachinery airfoils. The results of a series of detailed tests to evaluate the tunnel performance are also described. Testing was conducted for zero pressure gradient flow with natural boundary layer transition. Heat transfer data and boundary layer profiles are presented for a flow with 0.25 percent free-stream turbulence. The flow in the tunnel test-section was shown to be highly uniform and two-dimensional. Test boundary layer profile and convective heat transfer data were self-consistent and in excellent agreement with classic correlations. Test-section free-stream total pressure, multi-component turbulence intensity, longitudinal integral scale, and spectral distributions are presented for grid-generated turbulence levels ranging from 1 to 7 percent. The test-section free-stream turbulence was shown to be both homogeneous and nearly isotropic. Anticipated applications of the facility include studies of the heat transfer and aerodynamics for conditions typical of those existing on gas turbine airfoils.

Sign in / Sign up

Export Citation Format

Share Document