Quantification of Creep Cavitation in Welded Joint and Evaluation of Material Characteristics of Simulated Heat-Affected Zone in X 20 CrMoV 12 1 Steel

2000 ◽  
Vol 123 (1) ◽  
pp. 112-117 ◽  
Author(s):  
Yong-Keun Chung ◽  
Cheol-Hong Joo ◽  
Jong-Jin Park ◽  
Ik-Man Park ◽  
Hyo-Jin Kim
Keyword(s):  
Base Metal ◽  
Heat Affected Zone ◽  
Power Plants ◽  
Welded Joint ◽  
Charpy Impact ◽  
Creep Damage ◽  
Average Diameter ◽  
Damage Mechanism ◽  
Creep Rupture ◽  
Creep Cavitation

X 20 CrMoV 12 1(DIN 17 175) steel has been used for components subjected to high temperature in power plants and chemical and petroleum industries. Therefore, extensive studies have been made on this steel. However, these studies focused mainly on the base metal, and few studies on the welded joint have been reported. Actually, a large number of failures have occurred at the welded joint, so there is increasing need to investigate the characteristics of X 20 CrMoV 12 1 weldment. In this study, the interrupted and creep rupture tests were carried out and quantification of the creep damage was attempted for the X 20 CrMoV 12 1 welded joint. The interrupted and creep rupture tests were performed at four conditions\M650-60, 600-100, 600-120, and 575-150(|SDC-MPa)\Mon the X 20 CrMoV 12 1 welded joint specimens, respectively. It was revealed from the experimental results that creep damage mechanism of a welded joint was mainly creep cavitation, and that the intensively damaged area by creep cavitations was the transition region from fine-grained heat-affected zone (HAZ) to unaffected base metal, namely intercritical HAZ. For both the interrupted and ruptured specimens, quantification of creep damage was attempted by evaluating cavitated area fraction, average diameter, and the number of cavities with creep life fraction. In addition, on the basis of the heat input during the welding, microstructure, microhardness, and grain size of the actual intercritical HAZ, simulated HAZ was made in order to evaluate its material properties. For the simulated HAZ specimens, tensile, charpy impact, and creep rupture tests were carried out. As a result, yield, tensile strength, and elongation of simulated HAZ were similar to those of base metal, respectively, and impact property of simulated HAZ was slightly above base metal. Also, it was found that creep strength of simulated HAZ was inferior to that of the base metal.

scholarly journals The influence of manual metal arc multiple repair welding of long operated waterwall on the structure and hardness of the heat affected zone of welded joints

2017 ◽  
Vol 62 (1) ◽  
pp. 327-333 ◽  
Author(s):  
J. Pikuła ◽  
M. Łomozik ◽  
T. Pfeifer
Keyword(s):  
Heat Affected Zone ◽  
Welded Joints ◽  
Arc Welding ◽  
Power Plants ◽  
Welded Joint ◽  
Weld Bead ◽  
Boiler Steel ◽  
Metallographic Examination ◽  
Metal Arc Welding ◽  
High Degree

Abstract Welded installations failures of power plants, which are often result from a high degree of wear, requires suitable repairs. In the case of cracks formed in the weld bead of waterwall, weld bead is removed and new welded joint is prepared. However, it is associated with consecutive thermal cycles, which affect properties of heat affected zone of welded joint. This study presents the influence of multiple manual metal arc welding associated with repair activities of long operated waterwall of boiler steel on properties of repair welded joints. The work contains the results of macro and microscopic metallographic examination as well as the results of hardness measurements.

Gas metal arc welding of XPF800 steel for automotive industry: Microstructural evaluation and mechanical properties investigation

2021 ◽  
pp. 146442072110567
Author(s):  
Emre Korkmaz ◽  
Cemal Meran
Keyword(s):  
Mechanical Properties ◽  
Base Metal ◽  
Automotive Industry ◽  
Heat Affected Zone ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Charpy Impact ◽  
Optical Microscope ◽  
Metal Arc Welding ◽  
Heat Affected Zone Softening

In this study, the effect of gas metal arc welding on the mechanical and microstructure properties of hot-rolled XPF800 steel newly produced by TATA Steel has been investigated. This steel finds its role in the automotive industry as chassis and seating applications. The microstructure transformation during gas metal arc welding has been analyzed using scanning electron microscope, optical microscope, and energy dispersive X-ray spectrometry. Tensile, Charpy impact, and microhardness tests have been implemented to determine the mechanical properties of welded samples. Acceptable welded joints have been obtained using heat input in the range of 0.28–0.46 kJ/mm. It has been found that the base metal hardness of the welded sample is 320 HV0.1. On account of the heat-affected zone softening, the intercritical heat-affected zone hardness values have diminished ∼20% compared to base metal.

scholarly journals Estimating the Influences of Prior Residual Stress on the Creep Rupture Mechanism for P92 Steel

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 639 ◽  
Author(s):  
Dezheng Liu ◽  
Yan Li ◽  
Xiangdong Xie ◽  
Guijie Liang ◽  
Jing Zhao
Keyword(s):  
Residual Stress ◽  
Flow Stress ◽  
Power Plants ◽  
Creep Damage ◽  
Creep Rupture ◽  
Transgranular Fracture ◽  
Creep Tests ◽  
Energy Principle ◽  
P92 Steel ◽  
Rupture Mechanism

Creep damage is one of the main failure mechanisms of high Cr heat-resistant steel in power plants. Due to the complex changes of stress, strain, and damage at the tip of a creep crack with time, it is difficult to accurately evaluate the effects of residual stress on the creep rupture mechanism. In this study, two levels of residual stress were introduced in P92 high Cr alloy specimens using the local out-of-plane compression approach. The specimens were then subjected to thermal exposure at the temperature of 650 °C for accelerated creep tests. The chemical composition of P92 specimens was obtained using an FLS980-stm Edinburgh fluorescence spectrometer. Then, the constitutive coupling relation between the temperature and material intrinsic flow stress was established based on the Gibbs free energy principle. The effects of prior residual stress on the creep rupture mechanism were investigated by the finite element method (FEM) and experimental method. A comparison of the experimental and simulated results demonstrates that the effect of prior residual stress on the propagation of micro-cracks and the creep rupture time is significant. In sum, the transgranular fracture and the intergranular fracture can be observed in micrographs when the value of prior residual stress exceeds and is less than the material intrinsic flow stress, respectively.

Creep Strength Evaluation of a New and a Used Grade 91 Welded Joints by Using a Miniature Specimen

2018 ◽  
Author(s):  
Takashi Ogata
Keyword(s):  
Weld Metal ◽  
Strain Rate ◽  
Creep Strain ◽  
Base Metal ◽  
Welded Joints ◽  
Welded Joint ◽  
Creep Damage ◽  
Creep Strain Rate ◽  
Standard Size ◽  
Grade 91

Grade 91 is widely used for steam pipes and tubes in high temperature boilers of ultra-super critical power plants in Japan. It was reported that creep damage may initiate at the fine grain region within the heat affected zone (HAZ) in welded joints prior to the base metal, so called “Type IV” damage, which causes steam leakage in existing power plants. Therefore, development of creep damage assessment methods is not only an important but also an urgent subject to maintain operation reliability. In order to evaluate creep damage of welded joints based on finite element analyses, creep deformation properties of a base metal, a weld metal and a HAZ have to be obtained from creep tests. However, it is difficult to cut a standard size creep specimen from the HAZ region. Only a miniature size specimen is available from the narrow HAZ region. Therefore, development of creep testing and evaluation technique for miniature size specimens is highly expected. In this study, a miniature tensile type solid bar specimen with 1mm diameter was machined from a base metal, a weld metal and a HAZ of a new and a used Grade 91 welded joints, and creep tests of these miniature specimens were conducted by using a special developed creep testing machine. It was found that creep deformation property is almost identical between the base metal and weld metal, and creep strain rate of the HAZ is much faster than that of these metals in the new welded joint. Relationships between stress and creep strain rates of the base metal and the HAZ in the used welded joint are within scatter bands of those in the new material. On the other hand, creep strain rate of the weld metal in the used welded joint became much faster than that in the new one. Then both the standard size and the miniature size cross weld specimens were machined from the new and the used welded joints and were tested under the same temperature and stress conditions. Rupture time of the miniature cross weld specimen is much shorter than that of the standard size cross weld specimen. The finite element creep analysis of the specimens indicates that higher triaxiality stress yields within the HAZ of the standard size specimen than that of the miniature specimen causing faster creep strain rate in the HAZ of the miniature cross weld specimen.

Experimental and Numerical Evaluation of Fracture Toughness on Electron Beam Welded Joint in Al6061-T6

2016 ◽  
Author(s):  
W. Rekik ◽  
O. Ancelet ◽  
C. Gardin ◽  
F. Hamon
Keyword(s):  
Electron Beam ◽  
Mechanical Behavior ◽  
Yield Stress ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
Material Behavior ◽  
Failure Assessment ◽  
Tearing Resistance ◽  
Alloy 6061

In order to ensure the integrity of structures, failure assessment is required. In this context, the fracture behavior of an electron beam (EB) welded joint on thick plate of aluminum alloy 6061-T6 used for structural components of experimental nuclear reactors was investigated. In the particular case of welded structures, the tearing resistance is strongly dependent on the mismatch of the welded joint and the local behavior of each metallurgical zone. For a reliable analysis, the tensile mechanical behavior of each position of the welded joint was precisely determined by the use of a new measurement prototype. The toughness behavior under different configurations was then evaluated on CT specimens. From these experimental results a mechanical behavior contrast was highlighted. In fact, the fusion zone presents the lowest yield stress and a gradient is observed in the heat affected zone until the material behavior reaches of the base metal yield stress. On the contrary, the toughness of the welded zone is the highest and decreases strongly in the heat affected zone according to an exponential function until the base metal toughness is reached.

Evaluation of Creep Strength Reduction Factors for Welded Joints of Modified 9Cr-1Mo Steel (P91)

2006 ◽  
Author(s):  
Masaaki Tabuchi ◽  
Yukio Takahashi
Keyword(s):  
Base Metal ◽  
Creep Strength ◽  
Welded Joints ◽  
Welded Joint ◽  
Rupture Strength ◽  
Reduction Factor ◽  
Creep Rupture ◽  
Type Iv ◽  
Rupture Data ◽  
Term Creep

In order to review the allowable creep strength of high Cr ferritic steels, creep rupture data of base metal and welded joints have been collected and long-term creep strength have been analyzed in the SHC committee in Japan since 2004. In the present paper, the creep rupture data of 370 points for welded joint specimens of modified 9Cr-1Mo steel (ASME Grade 91) offered from seven Japanese companies and institutes were analyzed. These data clearly indicated that the creep strength of welded joints was lower than that of base metal due to Type IV fracture in HAZ at or above 600°C. From the activities of this committee, the master curve for life evaluation of welded joints of Gr.91 steel could be represented as follows: LMP==34154+3494(logσ)−2574(logσ)2,C=31.4 The reduction factor of 100,000 hours creep rupture strength of welded joint to base metal was concluded to be 0.75 at 600°C and 0.70 at 650°C for the Gr.91 steel.

scholarly journals MODELING THE WORK OF THE HEAD OF A HYDROMECHANICAL EXPANDER FOR WELDED PIPES OF A LARGE DIAMETER

2020 ◽  
pp. 35-42
Author(s):  
L. M. Gurevich ◽  
V. F. Danenko ◽  
A. A. Istrati ◽  
V. A. Sonnova
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Internal Pressure ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
Large Diameter ◽  
Design Parameters ◽  
Maximum Stresses ◽  
Distribution Of Stresses

Finite element simulates of changing stresses and strains under loading by gradually increasing internal pressure of cylindrical welded vessels was carried out. The vessels had an annular mechanically inhomogeneous welded joint with different mechanical properties of the joint, heat-affected zone, and base metal. Maximum stresses developed in the caps of the vessels, and the annular joint are lightly loaded. The distribution of stresses and strains in joint at various design parameters of the vessels is investigated.

Microstructural and mechanical characterization of the effect of the welding process on creep behavior of welded joint and base metal specimens of Inconel 600

MRS Advances ◽  
2020 ◽  
Vol 5 (59-60) ◽  
pp. 3003-3014
Author(s):  
Lourdes Y. Herrera-Chávez ◽  
Alberto Ruiz ◽  
Víctor H. López-Morelos ◽  
Carlos Rubio-González ◽  
Martín R. Barajas-Álvarez ◽  
...  
Keyword(s):  
Base Metal ◽  
Creep Behavior ◽  
Heat Affected Zone ◽  
Structural Integrity ◽  
Welded Joint ◽  
Welding Process ◽  
Creep Tests ◽  
Inconel 600 ◽  
Two Temperatures

AbstractIn this study, plates of Inconel 600 superalloy were gas metal arc welded to investigate the effects of the welding process on the creep behavior of the welded samples and compare it to the creep behavior of samples in the as-received condition. Creep tests were performed at two temperatures (600 and 650 °C) with different stress levels. During the welding process, three distinctive microstructural zones are generated, i.e. welded material, heat affected zone, and base metal that may affect the properties of the welded joint. Microstructural, elemental analysis of samples was conducted using Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDS). The experimental results show that creep rupture preferentially occurs in the heat-affected zone of the base metal at 4 mm from the fusion line and that the creep behavior of welded samples is different from that of the base metal. These results can be used in the design of structural components to assure their structural integrity.

Region-Specified Ratcheting Behavior of API X80 Welded Joint Under Uniaxial Cyclic Loading

2016 ◽  
Author(s):  
Hongsheng Lu ◽  
Yonghe Yang ◽  
Gang Chen ◽  
Xu Chen ◽  
Xin Wang
Keyword(s):  
Weld Metal ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
Pipeline Steel ◽  
Coarse Grained ◽  
Strain Accumulation ◽  
Lower Strength ◽  
Fine Grained ◽  
Ratcheting Strain

Evaluation of mechanical performance of different regions can be difficult by using standard size samples due to the size limitation of weld metal and heat-affected zone (HAZ). At first, the microstructure of different regions was characterized and quantified by Scanning Electron Microscope, which indicate that the pipeline steel is a typical acicular ferrite steel. In this study the deformation behavior of different regions (base metal, weld metal and heat affected zone) in a welded joint of API X80 pipeline steel were studied by conducting uniaxial loading tests on miniature specimens with the cross section of 2×0.5mm and gauge length of 9mm. From the results of uniaxial tension in base metal and weld metal it is shown that the welding is overmatching. Compared to the base metal, the coarse grained HAZ exhibits a lower strength, while the fine grained HAZ exhibits a higher strength. Under near zero-to-tension cyclic stress loading, all regions of the welded joints exhibit progressive accumulation of plastic strain. Under the same stress level, the base metal shows the fastest ratcheting strain accumulation, which is the result of lower strength than other regions. This fact may indicate that the ratcheting behavior of the overall welded joint is highly dependence on that of base metal for the present case. But when under the same normalized stress level (σ = σ/σYS), the fine grained HAZ has the highest ratcheting strain accumulation, while the coarse grained HAZ has the lowest ratcheting strain accumulation, which reveals that the intrinsic resistance to ratcheting is yield strength dependent.

Research on Microstructure and Properties of Welded Joint of 2205 Steel with FCAW

2011 ◽  
Vol 391-392 ◽  
pp. 763-767
Author(s):  
Li Yang ◽  
Na Zhang
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Duplex Stainless Steel ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
High Strength ◽  
Two Phase ◽  
Flux Cored Arc Welding ◽  
Mechanical Properties And Corrosion

On the basis of the analysis of composition, microstructure, properties and weldability of 2205 duplex stainless steel, the flux cored arc welding (FCAW) process is made. Then the microstructure, mechanical properties and corrosion resistance of welded joint were analyzed. The results shows using FCAW process, in order to obtain high strength, perfect impact toughness and overall and partial resistance to stress corrosion in welded joint, the Ni content of duplex stainless steel welding material should be 2% to 4% higher than that of base metal, multi-layer and multi-channel welding is adopted with the strict control of energy input less than or equal to 0.926KJ/mm, layer temperature is less than 120 °C, thus the appropriate proportion of two-phase structure in the welded joint can be got. Using a reasonable welding procedure, the microstructure in weld beam is austenite (A) + ferrite (F), and in heat affected zone is ferrite (F) + austenite (A) + a small amount of third phase, the content of austenite in weld beam and heat affected zone is higher than that of the base metal. Tensile strength of the welded joint is up to 854.5MPa and the fracture occurs in the base metal and the heat affected zone. The welded joint has high strength, good plasticity, toughness and corrosion resistance.

Sign in / Sign up

Export Citation Format

Share Document