scholarly journals Estimating the Influences of Prior Residual Stress on the Creep Rupture Mechanism for P92 Steel

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 639 ◽  
Author(s):  
Dezheng Liu ◽  
Yan Li ◽  
Xiangdong Xie ◽  
Guijie Liang ◽  
Jing Zhao
Keyword(s):  
Residual Stress ◽  
Flow Stress ◽  
Power Plants ◽  
Creep Damage ◽  
Creep Rupture ◽  
Transgranular Fracture ◽  
Creep Tests ◽  
Energy Principle ◽  
P92 Steel ◽  
Rupture Mechanism

Creep damage is one of the main failure mechanisms of high Cr heat-resistant steel in power plants. Due to the complex changes of stress, strain, and damage at the tip of a creep crack with time, it is difficult to accurately evaluate the effects of residual stress on the creep rupture mechanism. In this study, two levels of residual stress were introduced in P92 high Cr alloy specimens using the local out-of-plane compression approach. The specimens were then subjected to thermal exposure at the temperature of 650 °C for accelerated creep tests. The chemical composition of P92 specimens was obtained using an FLS980-stm Edinburgh fluorescence spectrometer. Then, the constitutive coupling relation between the temperature and material intrinsic flow stress was established based on the Gibbs free energy principle. The effects of prior residual stress on the creep rupture mechanism were investigated by the finite element method (FEM) and experimental method. A comparison of the experimental and simulated results demonstrates that the effect of prior residual stress on the propagation of micro-cracks and the creep rupture time is significant. In sum, the transgranular fracture and the intergranular fracture can be observed in micrographs when the value of prior residual stress exceeds and is less than the material intrinsic flow stress, respectively.

Creep Damage and Fracture in Advanced Tungsten Modified 9%Cr Ferritic Steel

2016 ◽  
Vol 713 ◽  
pp. 183-186 ◽  
Author(s):  
Vàclav Sklenička ◽  
K. Kuchařová ◽  
M. Kvapilová ◽  
Petr Král ◽  
Jiří Dvořák
Keyword(s):  
Creep Strength ◽  
Ferritic Steel ◽  
Nuclear Power ◽  
Power Plants ◽  
Creep Behaviour ◽  
Creep Damage ◽  
Creep Tests ◽  
P92 Steel ◽  
Damage And Fracture ◽  
Isothermal Ageing

Advanced tungsten modified 9%Cr ferritic steel (ASTM Grade P92) is a promising material for the next generation of fossil and nuclear power plants. Unfortunately, there are rather few published reports on damage processes in P92 steel during high temperature creep and the effect of damage evolution on the creep strength is not fully understood. In this work, the creep behaviour of P92 steel in as-received condition and after long-term isothermal ageing was investigated at 600 and 650°C using uniaxial tension creep tests. To quantify the effect of each damage process on the loss of creep strength, most of creep tests were followed by microstructural and fractographic investigations. It was found that the large Laves phase particles, which coarsened during creep exposure, served as preferential sites for creep cavity nucleation.

Creep Damage Evaluation of Fine-Grained HAZ in Mod. 9Cr Ferritic Heat-Resistant Steel Weldments

2007 ◽  
Author(s):  
N. Yoneyama ◽  
K. Kubushiro ◽  
H. Yoshizawa
Keyword(s):  
Creep Damage ◽  
Life Time ◽  
Creep Life ◽  
Creep Tests ◽  
Boundary Density ◽  
Fine Grained ◽  
Type Iv ◽  
Fine Grain ◽  
Type Iv Cracking ◽  
Rupture Mechanism

9Cr steel weldments are concerned with evaluation of creep life time and creep rupture mechanism. In fine grain HAZ (FG-HAZ) of weldments, TYPE IV cracking and creep voids occurred at lower stress than rupture stress level of base metal. In the crept specimen, FG-HAZ sometime has large coarsening grains near creep voids. These recovery phenomena are localized in FG-HAZ, and recovered microstructures are dependent on heat input of welding. In this study, creep tests are examined in two types of weldments, and relations between creep life time and coarsened sub-grains or grains have been studied by microstructural changing with EBSP analysis. In crept specimens, boundaries are moved and boundary density is decreasing in the fine-grained HAZ. Maximum grain size and creep life time have linear function, and EBSP can evaluate creep life time of 9Cr weldments. These microstructural changing are considered by morphology of precipitates in the several crept specimens.

Creep Fracture Analysis of W Strengthened 9% Cr Steel Weldment

2010 ◽  
Vol 154-155 ◽  
pp. 1699-1704
Author(s):  
Xue Wang ◽  
Qian Gang Pan ◽  
Zi Jun Liu ◽  
Hui Qiang Zeng ◽  
Yong Shun Tao
Keyword(s):  
Arc Welding ◽  
Rupture Strength ◽  
Fracture Analysis ◽  
Creep Rupture ◽  
Creep Rupture Strength ◽  
Creep Tests ◽  
P92 Steel ◽  
Fine Grained ◽  
Weld Joints ◽  
M23c6 Carbides

The creep rupture behaviour,hardness distribution and microstructure of weldment made by submerge arc welding for W strengthened P92 steel are described in this paper. The cross-weld creep tests were carried out at 923K under stresses in the ranges 130-100MPa. For stress below 120MPa, weld-joints were ruptured by the Type crack, which located in their fine-grained heat affected zone(FGHAZ)with the smallest measured cross-weld hardness. A strong drop in creep rupture strength of weldment was induced by brittle type failure. In addition to coarsening of M23C6 carbides and an equiaxed fine grains in FGHAZ, intermetallic Fe2(Mo,W)Laves phase precipitated on grain boundaries during creep is probably the significant factor caused the type failure.

Simulation of Creep Deformation and Rupture of Notched Bar Specimens of Grade 92 Steel

2015 ◽  
Author(s):  
Haruhisa Shigeyama ◽  
Yukio Takahashi ◽  
Jonathan Parker
Keyword(s):  
Creep Strain ◽  
Creep Behavior ◽  
Power Plants ◽  
Thermal Power ◽  
Failure Criteria ◽  
Creep Rupture ◽  
Creep Failure ◽  
Creep Tests ◽  
Round Bar ◽  
Grade 92 Steel

Creep strain equations of Grade 92 steel which is used in boilers and piping systems of ultra-supercritical (USC) thermal power plants were developed based on the results of creep tests on smooth round bar specimens of three kinds of Grade 92 steels. In these equations, primary creep behavior was represented by a power-law and tertiary creep behavior was described by an exponential function. Creep parameters were determined as a function of creep rupture times which were calculated from stress and absolute temperature. Additionally, generalized creep failure criteria considering the multiaxial stress were established on the basis of results of creep tests on circumferentially notched round bar specimens. These creep strain equations and creep failure criteria were incorporated into finite element analysis software. Then, creep failure analyses were carried out and the resulting deformation behavior and rupture times were compared with the experimental results. Creep rupture lives were predicted with a good accuracy, within a factor of two in most cases.

Development of Creep Damage in Similar Weld Joints of P92 Steel Pipe

2017 ◽  
Vol 270 ◽  
pp. 162-167
Author(s):  
Petr Král ◽  
Vaclav Sklenička ◽  
Květa Kuchařová ◽  
Marie Svobodová ◽  
Marie Kvapilová ◽  
...  
Keyword(s):  
Welded Joints ◽  
Creep Behaviour ◽  
Creep Damage ◽  
Electron Back Scatter Diffraction ◽  
Steel Pipe ◽  
Tensile Creep ◽  
Creep Tests ◽  
P92 Steel ◽  
Welding Technology ◽  
Fracture Ductility

The microstructure and creep behaviour of the welded joints of P92 steel pipe were investigated in order to determine the influence of orbital heat welding technology on the creep resistance. Creep specimens were machined from the welded joints. Tensile creep tests of welded joints were performed at 873 K using different stresses. The microstructure of tested specimens was investigated by scanning electron microscope Tescan equipped with an electron-back scatter diffraction. The creep results showed that the creep fracture strain of the welded joints decreases with decreasing value of applied stress. Microstructure investigation showed that fracture behaviour of welded joints is influenced by an enhanced cavity formation at grain boundaries in the heat-affected zone causing lower fracture ductility.

Quantification of Creep Cavitation in Welded Joint and Evaluation of Material Characteristics of Simulated Heat-Affected Zone in X 20 CrMoV 12 1 Steel

2000 ◽  
Vol 123 (1) ◽  
pp. 112-117 ◽  
Author(s):  
Yong-Keun Chung ◽  
Cheol-Hong Joo ◽  
Jong-Jin Park ◽  
Ik-Man Park ◽  
Hyo-Jin Kim
Keyword(s):  
Base Metal ◽  
Heat Affected Zone ◽  
Power Plants ◽  
Welded Joint ◽  
Charpy Impact ◽  
Creep Damage ◽  
Average Diameter ◽  
Damage Mechanism ◽  
Creep Rupture ◽  
Creep Cavitation

X 20 CrMoV 12 1(DIN 17 175) steel has been used for components subjected to high temperature in power plants and chemical and petroleum industries. Therefore, extensive studies have been made on this steel. However, these studies focused mainly on the base metal, and few studies on the welded joint have been reported. Actually, a large number of failures have occurred at the welded joint, so there is increasing need to investigate the characteristics of X 20 CrMoV 12 1 weldment. In this study, the interrupted and creep rupture tests were carried out and quantification of the creep damage was attempted for the X 20 CrMoV 12 1 welded joint. The interrupted and creep rupture tests were performed at four conditions\M650-60, 600-100, 600-120, and 575-150(|SDC-MPa)\Mon the X 20 CrMoV 12 1 welded joint specimens, respectively. It was revealed from the experimental results that creep damage mechanism of a welded joint was mainly creep cavitation, and that the intensively damaged area by creep cavitations was the transition region from fine-grained heat-affected zone (HAZ) to unaffected base metal, namely intercritical HAZ. For both the interrupted and ruptured specimens, quantification of creep damage was attempted by evaluating cavitated area fraction, average diameter, and the number of cavities with creep life fraction. In addition, on the basis of the heat input during the welding, microstructure, microhardness, and grain size of the actual intercritical HAZ, simulated HAZ was made in order to evaluate its material properties. For the simulated HAZ specimens, tensile, charpy impact, and creep rupture tests were carried out. As a result, yield, tensile strength, and elongation of simulated HAZ were similar to those of base metal, respectively, and impact property of simulated HAZ was slightly above base metal. Also, it was found that creep strength of simulated HAZ was inferior to that of the base metal.

scholarly journals Experimental Investigation and Modeling of Damage Accumulation of EN-AW 2024 Aluminum Alloy under Creep Condition at Elevated Temperature

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 404
Author(s):  
Adam Tomczyk ◽  
Andrzej Seweryn
Keyword(s):  
Damage Accumulation ◽  
Axial Stress ◽  
Axial Strain ◽  
Creep Condition ◽  
Creep Damage ◽  
Creep Rupture ◽  
Uniaxial Tensile ◽  
Creep Tests ◽  
Damage State ◽  
2024 Aluminum Alloy

The paper is focused on creep-rupture tests of samples made of the 2024 alloy in the T3511 temper under uniaxial tensile stress conditions. The basic characteristics of the material at the temperatures of 100, 200 and 300 °C were determined, such as the Young’s modulus E, yield point σy, ultimate tensile strength σc and parameters K and n of the Ramberg–Osgood equation. Creep tests were performed for several different levels of nominal axial stress (load) at each temperature. It was observed that in the process of creep to failure at 200 and 300 °C, as the stress decreases, the creep time increases and, at the same time, the strain at rupture increases. However, such a regularity is maintained until a certain transition stress value σt is reached. Reducing the stress below this value results in a decreased value of the strain at rupture. A simple model of creep damage accumulation was proposed for the stress range above the transient value. In this model, the increase in the isotropic damage state variable was made dependent on the value of axial stress and the increase in plastic axial strain. Using the results of experimental creep-rupture tests and the failure condition, the parameters of the proposed model were determined. The surface of fractures obtained in the creep tests with the use of SEM technology was also analyzed.

Type IV Creep Damage Analysis for Full Size Component Test on Welded P91 Boiler Hot Reheat Piping

2004 ◽  
Author(s):  
Fumio Takemasa ◽  
Isamu Nonaka ◽  
Takuya Ito ◽  
Kensuke Saitou ◽  
Yoshikazu Miyachi ◽  
...  
Keyword(s):  
Welded Joints ◽  
Power Plants ◽  
Creep Damage ◽  
Assessment Method ◽  
Life Assessment ◽  
Creep Tests ◽  
Full Size ◽  
Type Iv ◽  
Component Test ◽  
Creep Life Assessment

In order to establish the creep life assessment method for modified 9Cr-1Mo steel welded joints on hot reheat piping of generating power plants, internal pressure creep tests conducted with full size components are analysed using the finite element method (FEM). As a result, it is shown that the creep damage distribution in weld heat affected zone (HAZ) can be predicted by stress distribution in HAZ, and that average stress in HAZ can be a representative value for creep strength of welded joints.

Identification of Stress Multiaxiallity Effect on Creep Damage by a Combination of Experiments and Numerical Analyses

2009 ◽  
Author(s):  
Yukio Takahashi
Keyword(s):  
Finite Element ◽  
Synergetic Effect ◽  
Stress Triaxiality ◽  
Creep Damage ◽  
Compact Tension ◽  
Simple Expression ◽  
Creep Rupture ◽  
Creep Tests ◽  
Element Analysis ◽  
Rupture Behavior

Structural materials experience various stress states and their integrity under a wide variety of stress multiaxility needs to be evaluated in design and life management for various components. Especially creep rupture behavior is known to be quite sensitive to the stress multiaxiality. To systematically evaluate the multiaxial effect on creep rupture behavior of modified 9Cr-1Mo steel, a number of creep tests were conducted on round-bar specimens with circumferential notches. Strong effects of temperature and deformation rate on the reduction of area were observed and their synergetic effect was modeled by a simple expression. Then crack growth in compact tension specimens was simulated by finite element analysis to derive ductility under higher stress triaxiality. Finally, true rupture strain was expressed as a function of temperature, inelastic strain rate and triaxiality factor and its validity was demonstrated through finite element analyses on notched bar and compact tension specimens employing it as a local fracture criterion.

scholarly journals Influence of normalizing and tempering temperatures on the creep properties of P92 steel

2020 ◽  
Vol 39 (1) ◽  
pp. 178-188
Author(s):  
Lakshmiprasad Maddi ◽  
Atul Ramesh Ballal ◽  
Dilip Ramkrishna Peshwe ◽  
M. D. Mathew
Keyword(s):  
Power Plants ◽  
Rupture Strength ◽  
Rupture Life ◽  
Creep Rupture ◽  
Laves Phases ◽  
P92 Steel ◽  
Creep Properties ◽  
Martensitic Microstructure ◽  
Actual Service ◽  
Rupture Properties

AbstractP92 steel is used as a piping material in ultra super critical power plants that can be operated at steam temperatures up to 650°C. The changes in the martensitic microstructure of P92 steel must be evaluated thoroughly before it is put into actual service. In this study, indigenously developed P92 steel was used. The steel was subjected to normalizing and tempering heat treatments in the range of 1,040–1,060°C and 740–780°C. The changes in the microstructure were evaluated and creep-rupture properties were studied at test temperatures of 600 and 650°C. Although normalizing temperatures influenced the microstructure and creep strength marginally, the change in tempering temperatures led to significant changes. The creep rupture strength at 600°C was influenced largely by the changes in the dislocation substructure, while the precipitation of Laves phases was a significant observation made for 650°C test temperature. Proposed mechanisms for the microstructural evolution and its consequences on the rupture life are discussed in this study.

Sign in / Sign up

Export Citation Format

Share Document