HETEROGENEOUS TRANSESTERIFICATION OF RUBBER SEED OIL BIODIESEL PRODUCTION

2016 ◽  
Vol 78 (6-10) ◽  
Author(s):  
Mahanum Mohd Zamberi ◽  
Farid Nasir Ani ◽  
Mohd Fadzli Abdollah
Keyword(s):  
Reaction Time ◽  
Acid Value ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Characterization ◽  
Rubber Seed Oil ◽  
Weight Percentage ◽  
Astm D6751 ◽  
Central Composite ◽  
Very High

An experimental investigation was conducted to explore the effects of using waste cockle shells as a heterogeneous catalyst on the transesterification process of very high free fatty acid (FFA) rubber seeds oil with methanol. The waste cockle was calcined at 900oC for 4 hours and was employed as a source of calcium oxide (CaO). SEM, XRD and XRF were adopted to analyze the catalyst characterization. The process variables namely oil molar ratio, catalyst concentration and reaction time were optimized using response surface methodology (RSM) based on central composite design (CCD) method. The optimum yield of 88.06% was obtained for the final product of biodiesel with optimal conditions was obtained as: molar ratio of methanol to oil of around 15.57:1, 9 % catalyst weight percentage with 2.81 hours reaction time. All the fuel properties were analyzed according to the ASTM D6751 and EN-14214 standards in terms of viscosity, acid value, density and flash point.

Biodiesel Production From Crude Rubber Seed Oil Using Supercritical Methanol Transesterification

2015 ◽  
Vol 781 ◽  
pp. 655-658 ◽  
Author(s):  
Thakun Sawiwat ◽  
Somjai Kajorncheappunngam
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Supercritical Methanol ◽  
Rubber Seed Oil ◽  
Promising Alternative ◽  
Rubber Seed ◽  
Biodiesel Synthesis

Synthesis of biodiesel from rubber seed oil using a supercritical methanol was investigated under various reaction conditions (220 - 300°C, 80 - 180 bar) with reaction time of 1-15 min and oil:methanol molar ratio of 1:20 - 1:60. Free fatty acid methyl esters (FAMEs) content were analyzed by gas chromatography-mass spectroscopy (GC-MS). Most properties of produced biodiesel were in good agreement with biodiesel standard (EN 14214). The maximum FAME yield of 86.90% was obtained at 260°C, 160 bar, 5 min reaction time using oil:methanol molar ratio of 1:40. The result showed the acid value of rubber seed oil decreased to 0.58 mgKOH/g from initial 24 mgKOH/g to. It could be concluded from this findings that crude rubber seed oil is a promising alternative raw material for biodiesel synthesis via supercritical methanol tranesterification.

scholarly journals Reutealis Trisperma Oil Esterification: Optimization and Kinetic Study

Energies ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1513
Author(s):  
Riky Lim ◽  
Deog-Keun Kim ◽  
Jin-Suk Lee
Keyword(s):  
Kinetic Study ◽  
High Reliability ◽  
Acid Value ◽  
Ion Exchange Resin ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Loading ◽  
Order Model ◽  
Marginal Lands ◽  
Central Composite

Reutealis trisperma, due to its high kernel-oil yield (±50%) and long productivity (±70 years), is considered to be a promising feedstock for biodiesel production. In addition, this plant, which can thrive on marginal lands, is classified as a non-edible oil since it contains a toxin known as eleostearic acid. The present study aimed to optimize the esterification step in biodiesel production from R.trisperma oil catalyzed using sulfonic ion exchange resin Lewatit K2640. The optimization step was performed using a response surface methodology through the incorporation of a central composite design. A kinetic study was performed as well, based on the assumption of a pseudo-homogeneous second-order model. Catalyst loading was found to have the most significant impact on acid value, followed by temperature and methanol-to-oil molar ratio. The optimal conditions for the esterification step were 92 °C temperature, 5.34% catalyst loading, and 5.82:1 methanol-to-oil molar ratio. The acid value and FFA conversion of R.trisperma oil under these conditions were 2.49 mg KOH/g and 91.75%, respectively. The kinetics study revealed that the constructed model could fit the experimental data well with relatively high reliability. The activation energy required for the esterification of R.trisperma oil was 33.2 kJ/mol.

scholarly journals Optimization of Biodiesel Production Using Nanomagnetic CaO-Based Catalysts with Subcritical Methanol Transesterification of Rubber Seed Oil

Energies ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 230 ◽  
Author(s):  
Veronica Winoto ◽  
Nuttawan Yoswathana
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Acid Methyl Ester ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Loading ◽  
Optimum Conditions ◽  
Rubber Seed Oil ◽  
Box Behnken Design ◽  
Rubber Seed

The molar ratio of methanol to rubber seed oil (RSO), catalyst loading, and the reaction time of RSO biodiesel production were optimized in this work. The response surface methodology, using the Box–Behnken design, was analyzed to determine the optimum fatty acid methyl ester (FAME) yield. The performance of various nanomagnetic CaO-based catalysts—KF/CaO-Fe3O4, KF/CaO-Fe3O4-Li (Li additives), and KF/CaO-Fe3O4-Al (Al additives)—were compared. Rubber seed biodiesel was produced via the transesterification process under subcritical methanol conditions with nanomagnetic catalysts. The experimental results indicated that the KF/CaO-Fe3O4-Al nanomagnetic catalyst produced the highest FAME yield of 86.79%. The optimum conditions were a 28:1 molar ratio of methanol to RSO, 1.5 wt % catalyst, and 49 min reaction time. Al additives of KF/CaO-Fe3O4 nanomagnetic catalyst enhanced FAME yield without Al up to 18.17% and shortened the reaction time by up to 11 min.

scholarly journals Effect of Process Variables on the Transesterification Process of Palm Oil Sludge to Biodiesel

2019 ◽  
pp. 1-14
Author(s):  
O. A. Aworanti ◽  
A. O. Ajani ◽  
S. E. Agarry ◽  
K. A. Babatunde ◽  
O. D. Akinwunmi
Keyword(s):  
Reaction Time ◽  
Palm Oil ◽  
Research Work ◽  
Acid Value ◽  
Biodiesel Production ◽  
Oil Sludge ◽  
Molar Ratio ◽  
Catalyst Loading ◽  
Optimum Process ◽  
Process Variables

In this research work, the optimum process variables (catalyst, methanol to oil ratio and reaction time) for transesterification of palm oil sludge (POS) to biodiesel were studied. The transesterification process was carried by mixture of palm oil sludge, methanol and catalyst with the help of magnetic stirrer at 300 rpm and at temperature of 60ºC. The catalyst used for the process was potassium hydroxide (KOH). One-Factor-at-A-Time was used to select the possible optimum levels of process variable that gives high biodiesel yield. The study was evaluated by five levels  of methanol-to-oil ratio (1:1 – 12:1), catalyst (0.1- 2%) and reaction time (30 – 150 min).The optimum process variables for transesterification of palm oil sludge (POS) to achieved maximum biodiesel yield  were found to be methanol to oil molar ratio of 12:1, catalyst loading of 1.5wt% and reaction time of 30 min. At this optimum conditions the maximum biodiesel yield was 61.2%. The biodiesel produced from transesterification of palm oil sludge was characterized in order to determine the properties of the product. The density of POS is 857.0 kg/m3, kinematic viscosity of 5.38 mm2/s, flash point of 180°C, pour point of -5°C, and Acid value of 0.17 mgKOH/g. The biodiesel produced from transesterification of palm oil sludge meets the EN 14214 and ASTM 6751 standard. Thus, this study will be helpful to determine an efficient and economical procedure for biodiesel production from non-edible raw materials with high free fatty acid.

Esterification Deacidification of Zanthoxylum Bungeanum Seed Oil

2012 ◽  
Vol 512-515 ◽  
pp. 1615-1618
Author(s):  
Jian Zhang ◽  
Xuan Jun Wang
Keyword(s):  
Sulfuric Acid ◽  
Reaction Time ◽  
Seed Oil ◽  
Acid Value ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
One Step ◽  
Acid Catalyzed ◽  
Zanthoxylum Bungeanum ◽  
Acid Esterification

Effects of mole rate of methanol/oil, reaction time and technology on the free fatty acid ( FFA) level decrease of Zanthoxylum bungeanum seed oil with sulfuric acid as catalyst was investigated. Results show that, the acid level decreases with the mole rate of methanol/oil increases when the sulfuric acid is 2% based on the weight of Zanthoxylum bungeanum seed oil and reacting at 60°C for 2h. When the mole rate is 20~35∶1, the final acid value is less than 2mgKOH/g which meets the requirement for biodiesel production. When the mole rate is 25∶1, with sulfuric acid dosage 2% and reacting at 60°C, the acid value decreases fast at the beginning of the acid esterification. The acid value of ZSO was reduced to 1.56 mg KOH/g from 78.91 mg KOH/g by only one-step acid-catalyzed esterification with methanol-to-oil molar ratio 30:1, H2SO4 2%, temperature 60°C and reaction time 60 min, which was selected as optimum for the acid-catalyzed esterification.

Production of biodiesel from chicken wastes by various alcohol-catalyst combinations

2015 ◽  
Vol 26 (1) ◽  
pp. 36-45 ◽  
Author(s):  
Chia-Wei Lin ◽  
Shuo-Wen Tsai
Keyword(s):  
Reaction Time ◽  
Methyl Ester ◽  
Ethyl Ester ◽  
Sodium Ethoxide ◽  
Renewable Resource ◽  
Acid Value ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Potential Candidate ◽  
Short Reaction Time

An environmentally friendly biorefinery process for producing biodiesel from chicken wastes was performed for this study. Low acid value (0.13±0.01 mg KOH/g) chicken oil was obtained by preparing chicken wastes with moderate heating and filtration processes that minimized damage to the lipids and thus facilitated subsequent reactions. Methanol-lipids in a molar ratio of 6:1 and a methanol-ethanol-lipids mixture in a molar ratio of 3:3:1 were both reacted with 1% KOH catalyst for transesterfication. Furthermore, ethanol-lipids in a molar ration of 6:1 were analogously transesterified with 1% sodium ethoxide. The amounts of biodiesel were 771.54 mg/mL±15.28, 722.98 mg/mL±37.38, and 714.86 mg/ mL±29.99 from methanol, eth-anol, and a mixture of methanol/ethanol (3:3), respectively, after transesterification. The total amount of ethyl ester was comparable with the total amount of methyl ester. In addition, ethanol is a renewable resource and a biorefinery concept can be contributed for biodiesel production. Further-more, transesterification of chicken oil with a mixture of methanol/ethanol (3:3) only needed a relatively short reaction time of an hour. Densities, viscosities, sulphur contents, acid values, and flash points of all esters were within the specifications of CNS 15072 and EN 14214. The transesterification system for chicken oil in ethanol and mixed methanol/ethanol (3:3) demonstrated in this study is a potential candidate for biodiesel production.

scholarly journals Biodiesel Production from Reutealis trisperma Oil Using Conventional and Ultrasonication through Esterification and Transesterification

2021 ◽  
Vol 13 (6) ◽  
pp. 3350
Author(s):  
Teuku Meurah Indra Riayatsyah ◽  
Razali Thaib ◽  
Arridina Susan Silitonga ◽  
Jassinnee Milano ◽  
Abd. Halim Shamsuddin ◽  
...  
Keyword(s):  
Reaction Time ◽  
Optimum Condition ◽  
Conventional Method ◽  
Fossil Fuel ◽  
Calorific Value ◽  
Acid Value ◽  
Biodiesel Production ◽  
Ultrasonic Bath ◽  
Negative Environmental Impact ◽  
Astm D6751

The limitation of fossil fuel sources and negative environmental impact persuade scientists around the world to find a solution. One possible solution is by using renewable fuel to replace fossil fuel with an inexpensive, fast, and effective production process. The objective of this study is to investigate the biodiesel production from crude Reutealis trisperma oil using the conventional and the ultrasonic bath stirrer method through the esterification and transesterification process. The result shows that the most effective reaction time with an optimum condition for the esterification and transesterification of Reutealis trisperma oil is at 2 h 30 min by using the ultrasonic bath stirrer method. The optimum conditions at a temperature of 55 °C for the esterification and at 60 °C for transesterification with 2% (v/v) of sulphuric acid with catalyst concentration of 0.5 wt.% were a methanol-to-oil ratio of 60%, and agitation speed of 1000 rpm. This optimum condition gives the highest yield of 95.29% for the Reutealis trisperma biodiesel. The results showed that the ultrasonic bath stirrer method had more effect on the reaction time needed than using the conventional method and reduced half of the conventional method reaction time. Finally, the properties of Reutealis trisperma biodiesel fulfilled the ASTM D6751 and EN 14214 biodiesel standards with density, 892 kg/m3; pour point, −2 °C; cloud point, −1 °C; flash point, 206.5 °C; calorific value, 40.098 MJ/kg; and acid value, 0.26 mg KOH/g.

scholarly journals Biodiesel Production from Waste Palm Oil Catalyzed by Hierarchical ZSM-5 Supported Calcium Oxide

2018 ◽  
Vol 16 (1) ◽  
pp. 98 ◽  
Author(s):  
Yusuf Muhammad Zein ◽  
Anil Kumar Anal ◽  
Didik Prasetyoko ◽  
Imroatul Qoniah
Keyword(s):  
Calcium Oxide ◽  
Palm Oil ◽  
Kinematic Viscosity ◽  
Acid Value ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Catalyst Amount ◽  
Maximum Conversion ◽  
Astm D6751 ◽  
Methyl Ester Content

Biodiesel production from waste palm oil catalyzed by hierarchical ZSM-5 supported calcium oxide was studied. The activity of CaO increased after supported on h-ZSM-5 resulting an increase in conversion from 93.17% to 95.40%. A maximum conversion of 95.40% was achieved at 6 h reaction time, 3 wt.% catalyst amount, 12:1 methanol to oil molar ratio and 65 °C reaction temperature. The waste palm oil showed a high potential as a feedstock in biodiesel production in which there was no significant different in the conversion of fresh and waste palm oil. The properties of the obtained biodiesel required the limits of biodiesel specification according to ASTM D6751-08 and EN 14214 with the methyl ester content of 97.18%, the acid value of 0.24 mg KOH/g, the kinematic viscosity of 4.64 cSt and the density of 869.9 kg/m3.

scholarly journals Utilization of Waste Grooved Razor Shell (GRS) as a Catalyst in Biodiesel Production from Refined and Waste Cooking Oils

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 703 ◽  
Author(s):  
Abdellah Aitlaalim ◽  
Fatiha Ouanji ◽  
Abdellah Benzaouak ◽  
Mohammed El Mahi ◽  
El Mostapha Lotfi ◽  
...  
Keyword(s):  
Large Scale ◽  
Raw Materials ◽  
Batch Reactor ◽  
Acid Value ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Lower Amount ◽  
Weight Percentage ◽  
Main Component ◽  
Cooking Oils

Biodiesel is a potential alternative for fossil fuel. However, its large-scale application is held up by the disadvantage of a homogenous process, the scarce availability of raw materials and the production cost, which is higher than for fossil diesel. In this work, biodiesel production was carried out using both refined and used cooking oils. The process was investigated in a batch reactor, in the presence of CaO as a heterogeneous catalyst prepared by the calcination of the natural Waste Grooved Razor Shell (GRS). Characterizations by X-Ray Diffraction (XRD) and Thermal Gravimetric (TG)/Differential Thermal Analysis (DTA) showed that the as-received GRS consists of aragonite, (i.e., CaCO3) as the main component and of water and organic matter in a lower amount. After calcination at 900 °C, CaO was formed as the only crystalline phase. The effects of several experimental parameters in the transesterification reactions were studied, and their impact on the produced biodiesel properties was investigated. The studied variables were the methanol/oil molar ratio, the catalyst weight percentage (with respect to the oil mass), the calcination temperature of the parent GRS and the recycling and regeneration of the catalyst. The physico-chemical and fuel properties, i.e., viscosity, density and acid value of used oils and of the produced biodiesel, were determined by conventional methods (American Society for Testing and Materials (ASTM) methods) and compared with the European standards of biodiesel. The optimal identified conditions were the following: the use of a 15:1 methanol/oil molar ratio and 5 wt% of CaO with respect to the oil mass. After 3 h of reaction at 65 °C, the biodiesel yield was equal to 94% and 99% starting from waste and refined oils, respectively.

scholarly journals Biodiesel Production from a Novel Nonedible Feedstock, Soursop (Annona muricata L.) Seed Oil

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2562 ◽  
Author(s):  
Chia-Hung Su ◽  
Hoang Nguyen ◽  
Uyen Pham ◽  
My Nguyen ◽  
Horng-Yi Juan
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Annona Muricata ◽  
Reaction Conditions ◽  
Biodiesel Feedstock ◽  
Acid Catalyzed ◽  
American Society ◽  
Optimal Reaction

This study investigated the optimal reaction conditions for biodiesel production from soursop (Annona muricata) seeds. A high oil yield of 29.6% (w/w) could be obtained from soursop seeds. Oil extracted from soursop seeds was then converted into biodiesel through two-step transesterification process. A highest biodiesel yield of 97.02% was achieved under optimal acid-catalyzed esterification conditions (temperature: 65 °C, 1% H2SO4, reaction time: 90 min, and a methanol:oil molar ratio: 10:1) and optimal alkali-catalyzed transesterification conditions (temperature: 65 °C, reaction time: 30 min, 0.6% NaOH, and a methanol:oil molar ratio: 8:1). The properties of soursop biodiesel were determined and most were found to meet the European standard EN 14214 and American Society for Testing and Materials standard D6751. This study suggests that soursop seed oil is a promising biodiesel feedstock and that soursop biodiesel is a viable alternative to petrodiesel.

Sign in / Sign up

Export Citation Format

Share Document