Backscattered electron image of osmium-impregnated/macerated tissues as a novel technique for identifying the cis -face of the Golgi apparatus by high-resolution scanning electron microscopy

2016 ◽  
Vol 263 (1) ◽  
pp. 87-96 ◽  
Author(s):  
D. KOGA ◽  
H. BOCHIMOTO ◽  
T. WATANABE ◽  
T. USHIKI
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Resolution ◽  
Golgi Apparatus ◽  
Novel Technique ◽  
Electron Image ◽  
Backscattered Electron ◽  
Scanning Electron

Automated Inclusion Microanalysis in Steel by Computer-Based Scanning Electron Microscopy: Accelerating Voltage, Backscattered Electron Image Quality, and Analysis Time

2017 ◽  
Vol 23 (6) ◽  
pp. 1082-1090 ◽  
Author(s):  
Dai Tang ◽  
Mauro E. Ferreira ◽  
Petrus C. Pistorius
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Quantitative Information ◽  
X Rays ◽  
Electron Image ◽  
Backscattered Electron ◽  
Computer Based ◽  
Inclusion Distribution ◽  
Distribution Composition ◽  
Scanning Electron

AbstractAutomated inclusion microanalysis in steel samples by computer-based scanning electron microscopy provides rapid quantitative information on micro-inclusion distribution, composition, size distribution, morphology, and concentration. Performing the analysis at a lower accelerating voltage (10 kV), rather than the generally used 20 kV, improves analysis accuracy and may improve spatial resolution, but at the cost of a smaller backscattered electron signal and potentially smaller rate of generation of characteristic X-rays. These effects were quantified by simulation and practical measurements.

Examination of Schistosome Cercariae and Schistosomules by Scanning Electron Microscopy

1969 ◽  
Vol 27 ◽  
pp. 50-51
Author(s):  
D. Johnson ◽  
P. Moriearty
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Resolution ◽  
Light Microscopy ◽  
Surface Structure ◽  
Extensive Study ◽  
Scanning Microscopy ◽  
Host Parasite ◽  
Conventional Electron Microscopy ◽  
Scanning Electron

Since several species of Schistosoma, or blood fluke, parasitize man, these trematodes have been subjected to extensive study. Light microscopy and conventional electron microscopy have yielded much information about the morphology of the various stages; however, scanning electron microscopy has been little utilized for this purpose. As the figures demonstrate, scanning microscopy is particularly helpful in studying at high resolution characteristics of surface structure, which are important in determining host-parasite relationships.

High Resolution Scanning Electron Microscopy

1991 ◽  
Vol 49 ◽  
pp. 478-479
Author(s):  
David Joy ◽  
James Pawley
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Electron Beam ◽  
Electron Microscope ◽  
High Resolution ◽  
Scanning Electron Microscope ◽  
Electron Probe ◽  
Impact Point ◽  
Interaction Volume ◽  
Scanning Electron

The scanning electron microscope (SEM) builds up an image by sampling contiguous sub-volumes near the surface of the specimen. A fine electron beam selectively excites each sub-volume and then the intensity of some resulting signal is measured. The spatial resolution of images made using such a process is limited by at least three factors. Two of these determine the size of the interaction volume: the size of the electron probe and the extent to which detectable signal is excited from locations remote from the beam impact point. A third limitation emerges from the fact that the probing beam is composed of a finite number of discrete particles and therefore that the accuracy with which any detectable signal can be measured is limited by Poisson statistics applied to this number (or to the number of events actually detected if this is smaller).

Scanning Electron Microscopy and x-ray analysis of microparticles and early hydration effects

1995 ◽  
Vol 53 ◽  
pp. 692-693
Author(s):  
Yun Lu ◽  
David C. Joy
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Resolution ◽  
Morphological Development ◽  
Early Hydration ◽  
X Ray ◽  
Blended Cements ◽  
Powder Particles ◽  
Chemical Wastes ◽  
Scanning Electron

High resolution scanning electron microscopy (SEM) and energy dispersive x-ray analysis (EDXA) were performed to investigate microparticles in blended cements and their hydration products containing sodium-rich chemical wastes. The physical appearance of powder particles and the morphological development at different hydration stages were characterized by using high resolution SEM Hitachi S-900 and by SEM S-800 with a EDX spectrometer. Microparticles were dispersed on the sample holder and glued by 1% palomino solution. Hydrated bulk samples were dehydrated by acetone and mounted on the holder by silver paste. Both fracture surfaces and flat cutting sections of hydrating samples were prepared and examined. Some specimens were coated with an 3 nm thick Au-Pd or Cr layer to provide good conducting surfaces. For high resolution SEM S-900 observations the accelerating voltage of electrons was 1-2 KeV to protect the electron charging. Microchemical analyses were carried out by S800/EDS equipped with a LINK detector of take-off angle =40°.

Progress in high-resolution CRYO-SEM imaging of viral particles

1996 ◽  
Vol 54 ◽  
pp. 818-819
Author(s):  
Ya Chen ◽  
Geoffrey Letchworth ◽  
John White
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Resolution ◽  
Structural Information ◽  
Signal To Noise Ratio ◽  
Flexible Structures ◽  
Simian Virus ◽  
Topographic Features ◽  
Viral Particles ◽  
Scanning Electron

Low-temperature high-resolution scanning electron microscopy (cryo-HRSEM) has been successfully utilized to image biological macromolecular complexes at nanometer resolution. Recently, imaging of individual viral particles such as reovirus using cryo-HRSEM or simian virus (SIV) using HRSEM, HV-STEM and AFM have been reported. Although conventional electron microscopy (e.g., negative staining, replica, embedding and section), or cryo-TEM technique are widely used in studying of the architectures of viral particles, scanning electron microscopy presents two major advantages. First, secondary electron signal of SEM represents mostly surface topographic features. The topographic details of a biological assembly can be viewed directly and will not be obscured by signals from the opposite surface or from internal structures. Second, SEM may produce high contrast and signal-to-noise ratio images. As a result of this important feature, it is capable of visualizing not only individual virus particles, but also asymmetric or flexible structures. The 2-3 nm resolution obtained using high resolution cryo-SEM made it possible to provide useful surface structural information of macromolecule complexes within cells and tissues. In this study, cryo-HRSEM is utilized to visualize the distribution of glycoproteins of a herpesvirus.

Imaging of polymer single crystals in low-voltage, high-resolution scanning electron microscopy

1990 ◽  
Vol 48 (4) ◽  
pp. 1106-1107
Author(s):  
W.W. Adams ◽  
G. Price ◽  
A. Krause
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Resolution ◽  
Single Crystals ◽  
Low Voltage ◽  
Polymer Surface ◽  
Beam Current ◽  
Image Features ◽  
First Results ◽  
Scanning Electron

It has been shown that there are numerous advantages in imaging both coated and uncoated polymers in scanning electron microscopy (SEM) at low voltages (LV) from 0.5 to 2.0 keV compared to imaging at conventional voltages of 10 to 20 keV. The disadvantages of LVSEM of degraded resolution and decreased beam current have been overcome with the new generation of field emission gun SEMs. In imaging metal coated polymers in LVSEM beam damage is reduced, contrast is improved, and charging from irregularly shaped features (which may be unevenly coated) is reduced or eliminated. Imaging uncoated polymers in LVSEM allows direct observation of the surface with little or no charging and with no alterations of surface features from the metal coating process required for higher voltage imaging. This is particularly important for high resolution (HR) studies of polymers where it is desired to image features 1 to 10 nm in size. Metal sputter coating techniques produce a 10 - 20 nm film that has its own texture which can obscure topographical features of the original polymer surface. In examining thin, uncoated insulating samples on a conducting substrate at low voltages the effect of sample-beam interactions on image formation and resolution will differ significantly from the effect at higher accelerating voltages. We discuss here sample-beam interactions in single crystals on conducting substrates at low voltages and also present the first results on HRSEM of single crystal morphologies which show some of these effects.

Electrostatic Adhesion Testing for the Evaluation of Metallization Adhesion

1997 ◽  
Vol 473 ◽  
Author(s):  
H. S. Yang ◽  
F. R. Brotzen ◽  
D. L. Callahan ◽  
C. F. Dunn
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Distribution Function ◽  
Quantitative Measurement ◽  
Multilayer Films ◽  
Adhesion Testing ◽  
Novel Technique ◽  
Electrostatic Adhesion ◽  
Scanning Electron

ABSTRACTQuantitative measurement of the adhesion strength of thin film metallizations has been achieved by a novel technique employing electrostatic forces to generate delaminating stresses. This technique has been used in testing the adhesion of Al-Cu, Cu, and Al multilayer films deposited on Si. Micro-blister-type failure is revealed by scanning electron microscopy. The delamination process and the geometry of the blister are discussed. The measured adhesion data fit a Weibull distribution function.

Sign in / Sign up

Export Citation Format

Share Document