Wind Turbine With Mechanical Power Split Transmission to Reduce the Power Electronic Devices: An Experimental Validation

2017 ◽  
Vol 64 (11) ◽  
pp. 8811-8820 ◽  
Author(s):  
Qian Liu ◽  
Rudiger Appunn ◽  
Kay Hameyer
Keyword(s):  
Wind Turbine ◽  
Experimental Validation ◽  
Electronic Devices ◽  
Mechanical Power ◽  
Power Electronic ◽  
Power Split

Lifetime Model for the Fatigue Fracture in Cu/Al2O3/Cu Composites: Experimental Validation of a Substantial Lifetime Enhancement by Cu Step Etching

2020 ◽  
Vol 142 (2) ◽  
Author(s):  
Patrick Gaiser ◽  
Markus Klingler ◽  
Jürgen Wilde
Keyword(s):  
Fatigue Fracture ◽  
Crack Detection ◽  
Experimental Validation ◽  
Heat Dissipation ◽  
Electronic Devices ◽  
Power Device ◽  
Power Electronic ◽  
Fem Simulations ◽  
Detection Techniques ◽  
Lifetime Model

Abstract Direct bonded copper (DBC) alumina (Al2O3) substrates are used in power electronic devices in order to transfer the heat from semiconductor devices to the heat sink and to carry high electric currents. Fatigue-induced cracks in the ceramic result in a diminished heat dissipation, leading to failure of a power device. Hence, a lifetime model concerning this failure mode is necessary. In this paper, a new lifetime model including crack initiation as well as crack propagation for the fatigue fracture of Al2O3-based DBC substrates is presented. It is based on experimental crack detection techniques and finite element method (FEM) simulations including fracture mechanics. For the validation of the lifetime model, experiments are presented which show that by appropriate design of the copper edge, the lifetime of the substrates is increased substantially.

Simulations technique for the design of a vertical axis wind turbine device with experimental validation

2013 ◽  
Vol 111 ◽  
pp. 1195-1203 ◽  
Author(s):  
S. Rolland ◽  
W. Newton ◽  
A.J. Williams ◽  
T.N. Croft ◽  
D.T. Gethin ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Experimental Validation ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine

scholarly journals Research on Small Square PCB Rogowski Coil Measuring Transient Current in the Power Electronics Devices

Sensors ◽  
2019 ◽  
Vol 19 (19) ◽  
pp. 4176 ◽  
Author(s):  
Chaoqun Jiao ◽  
Juan Zhang ◽  
Zhibin Zhao ◽  
Zuoming Zhang ◽  
Yuanliang Fan
Keyword(s):  
Power Electronics ◽  
Printed Circuit Board ◽  
Electronic Devices ◽  
Rogowski Coil ◽  
Bipolar Transistors ◽  
Circuit Board ◽  
Power Electronic ◽  
Insulated Gate Bipolar Transistors ◽  
Printed Circuit ◽  
Internal Structures

With the development of China’s electric power, power electronics devices such as insulated-gate bipolar transistors (IGBTs) have been widely used in the field of high voltages and large currents. However, the currents in these power electronic devices are transient. For example, the uneven currents and internal chip currents overshoot, which may occur when turning on and off, and could have a great impact on the device. In order to study the reliability of these power electronics devices, this paper proposes a miniature printed circuit board (PCB) Rogowski coil that measures the current of these power electronics devices without changing their internal structures, which provides a reference for the subsequent reliability of their designs.

scholarly journals New Sensor for Medium- and High-Voltage Measurement

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4654
Author(s):  
Andrzej Wetula ◽  
Andrzej Bień ◽  
Mrunal Parekh
Keyword(s):  
Finite Element Method ◽  
Electronic Devices ◽  
Finite Element Method Simulation ◽  
Laboratory Model ◽  
Power Electronic ◽  
Proof Of Concept ◽  
Voltage Measurement ◽  
Medium Voltage ◽  
Narrow Frequency Band ◽  
Further Development

Measurements of medium and high voltages in a power grid are normally performed with large and bulky voltage transformers or capacitive dividers. Besides installation problems, these devices operate in a relatively narrow frequency band, which limits their usability in modern systems that are saturated with power electronic devices. A sensor that can be installed directly on a wire and can operate without a galvanic connection to the ground may be used as an alternative voltage measurement device. This type of voltage sensor can complement current sensors installed on a wire, forming a complete power acquisition system. This paper presents such a sensor. Our sensor is built using two dielectric elements with different permeability coefficients. A finite element method simulation is used to estimate the parameters of a constructed sensor. Besides simulations, a laboratory model of a sensor was built and tested in a medium-voltage substation. Our results provide a proof of concept for the presented sensor. Some errors in voltage reconstruction have been traced to an oversimplified data acquisition and transmission system, which has to be improved during the further development of the sensor.

scholarly journals Series Compensation of Transmission Systems: A Literature Survey

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1717
Author(s):  
Camilo Andrés Ordóñez ◽  
Antonio Gómez-Expósito ◽  
José María Maza-Ortega
Keyword(s):  
Steady State ◽  
Power Systems ◽  
Power System ◽  
Case Studies ◽  
Electronic Devices ◽  
Literature Survey ◽  
Power Electronic ◽  
Transmission Systems ◽  
Series Compensation ◽  
Near Future

This paper reviews the basics of series compensation in transmission systems through a literature survey. The benefits that this technology brings to enhance the steady state and dynamic operation of power systems are analyzed. The review outlines the evolution of the series compensation technologies, from mechanically operated switches to line- and self-commutated power electronic devices, covering control issues, different applications, practical realizations, and case studies. Finally, the paper closes with the major challenges that this technology will face in the near future to achieve a fully decarbonized power system.

Sign in / Sign up

Export Citation Format

Share Document