Improved noise characteristics of an X-band helix-TWT driven by a low noise solid state amplifier

2004 ◽  
Author(s):  
Ji Ilan Joo ◽  
Min Ho Son ◽  
Young Ho Na ◽  
Jin Joo Choi
Keyword(s):  
Solid State ◽  
Low Noise ◽  
Noise Characteristics ◽  
X Band

scholarly journals A Tri-Band Cooled Receiver for Geodetic VLBI

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2662
Author(s):  
José A. López-Pérez ◽  
Félix Tercero-Martínez ◽  
José M. Serna-Puente ◽  
Beatriz Vaquero-Jiménez ◽  
María Patino-Esteban ◽  
...  
Keyword(s):  
Very Long Baseline Interferometry ◽  
Low Noise ◽  
Cryogenic Temperatures ◽  
Geospatial Information ◽  
Receiver Noise ◽  
Geodetic Vlbi ◽  
Long Baseline ◽  
Front End ◽  
X Band ◽  
Santa Maria

This paper shows a simultaneous tri-band (S: 2.2–2.7 GHz, X: 7.5–9 GHz and Ka: 28–33 GHz) low-noise cryogenic receiver for geodetic Very Long Baseline Interferometry (geo-VLBI) which has been developed at Yebes Observatory laboratories in Spain. A special feature is that the whole receiver front-end is fully coolable down to cryogenic temperatures to minimize receiver noise. It was installed in the first radio telescope of the Red Atlántica de Estaciones Geodinámicas y Espaciales (RAEGE) project, which is located in Yebes Observatory, in the frame of the VLBI Global Observing System (VGOS). After this, the receiver was borrowed by the Norwegian Mapping Autorithy (NMA) for the commissioning of two VGOS radiotelescopes in Svalbard (Norway). A second identical receiver was built for the Ishioka VGOS station of the Geospatial Information Authority (GSI) of Japan, and a third one for the second RAEGE VGOS station, located in Santa María (Açores Archipelago, Portugal). The average receiver noise temperatures are 21, 23, and 25 Kelvin and the measured antenna efficiencies are 70%, 75%, and 60% in S-band, X-band, and Ka-band, respectively.

scholarly journals A Four-Channel Low-Noise Readout IC for Air Flow Measurement Using Hot Wire Anemometer in 0.18 μm CMOS Technology

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4694
Author(s):  
Kyeongsik Nam ◽  
Hyungseup Kim ◽  
Yongsu Kwon ◽  
Gyuri Choi ◽  
Taeyup Kim ◽  
...  
Keyword(s):  
Supply Voltage ◽  
Air Flow ◽  
Low Noise ◽  
Cmos Process ◽  
Significant Information ◽  
Flow Measurements ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Op Amp ◽  
Noise Characteristics

Air flow measurements provide significant information required for understanding the characteristics of insect movement. This study proposes a four-channel low-noise readout integrated circuit (IC) in order to measure air flow (air velocity), which can be beneficial to insect biomimetic robot systems that have been studied recently. Instrumentation amplifiers (IAs) with low-noise characteristics in readout ICs are essential because the air flow of an insect’s movement, which is electrically converted using a microelectromechanical systems (MEMS) sensor, generally produces a small signal. The fundamental architecture employed in the readout IC is a three op amp IA, and it accomplishes low-noise characteristics by chopping. Moreover, the readout IC has a four-channel input structure and implements an automatic offset calibration loop (AOCL) for input offset correction. The AOCL based on the binary search logic adjusts the output offset by controlling the input voltage bias generated by the R-2R digital-to-analog converter (DAC). The electrically converted air flow signal is amplified using a three op amp IA, which is passed through a low-pass filter (LPF) for ripple rejection that is generated by chopping, and converted to a digital code by a 12-bit successive approximation register (SAR) analog-to-digital converter (ADC). Furthermore, the readout IC contains a low-dropout (LDO) regulator that enables the supply voltage to drive digital circuits, and a serial peripheral interface (SPI) for digital communication. The readout IC is designed with a 0.18 μm CMOS process and the current consumption is 1.886 mA at 3.3 V supply voltage. The IC has an active area of 6.78 mm2 and input-referred noise (IRN) characteristics of 95.4 nV/√Hz at 1 Hz.

Measuring Trapped DNA at the Liquid-Air Interface for Enhanced Single Molecule Sensing

Nanoscale ◽  
2021 ◽  
Author(s):  
Nasim Farajpour ◽  
Lauren Lastra ◽  
Vinay Sharma ◽  
Kevin Freedman
Keyword(s):  
Solid State ◽  
Single Molecule ◽  
Borosilicate Glass ◽  
Low Noise ◽  
Viable Alternative ◽  
Single Molecule Detection ◽  
Widespread Application ◽  
Promising Tool ◽  
Air Interface ◽  
Cost Efficient

Nanopore sensing is a promising tool with widespread application in single-molecule detection. Borosilicate glass nanopores are a viable alternative to other solid-state nanopores due to low noise and cost-efficient fabrication....

Sign in / Sign up

Export Citation Format

Share Document