Enhancing component level reliability of Pb-free flip chip package of Cu/low-K devices using FEM-based sensitivity analysis

2007 ◽  
Author(s):  
Kuo-Chin Chang ◽  
Chang-Chun Lee ◽  
Han-Ping Pu ◽  
Mirng-Ji Lii
Keyword(s):  
Sensitivity Analysis ◽  
Flip Chip ◽  
Component Level ◽  
Low K

C4 EM and CPI Reliability Benefits and Process Challenges of FBEOL Integration Changes Implemented in Lead-free C4 Products

2015 ◽  
Vol 2015 (1) ◽  
pp. 000787-000792
Author(s):  
E. Misra ◽  
T. Wassick ◽  
I. Melville ◽  
K. Tunga ◽  
D. Questad ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Flip Chip ◽  
Process Integration ◽  
Semiconductor Industry ◽  
Lead Free ◽  
Solder Interconnects ◽  
Design Changes ◽  
Modeling Data ◽  
Free Solder ◽  
Low K

The introduction of low-k & ultra-low-k dielectrics, lead-free (Pb-free) solder interconnects or C4's, and organic flip-chip laminates for integrated circuits have led to some major reliability challenges for the semiconductor industry. These include C4 electromigration (EM) and mechanical failures induced with-in the Si chip due to chip-package interactions (CPI). In 32nm technology, certain novel design changes were evaluated in the last Cu wiring level and the Far Back End of Line levels (FBEOL) to strategically re-distribute the current more uniformly through the Pb-free C4 bumps and therefore improve the C4 EM capabilities of the technology. FBEOL process integration changes, such as increasing the thickness of the hard dielectric (SiNx & SiOx) and reducing the final via diameter, were also evaluated for reducing the mechanical stresses in the weaker BEOL levels and mitigating potential risks for mechanical failures within the Si chip. The supporting white-bump, C4 EM and electrical/mechanical modeling data that demonstrates the benefits of the design and integration changes will be discussed in detail in the paper. Some of the key processing and integration challenges observed due to the design and process updates and the corresponding mitigation steps taken will also be discussed.

Microstructure Observation of Electromigration Behavior in Peripheral C2 Flip Chip Interconnection with Solder Capped Cu Pillar Bump

2011 ◽  
Vol 2011 (1) ◽  
pp. 000828-000836
Author(s):  
Yasumitsu Orii ◽  
Kazushige Toriyama ◽  
Sayuri Kohara ◽  
Hirokazu Noma ◽  
Keishi Okamoto ◽  
...  
Keyword(s):  
Aging Process ◽  
Flip Chip ◽  
Fem Simulation ◽  
Organic Substrate ◽  
Organic Substrates ◽  
Cross Sectional ◽  
Pillar Height ◽  
Cu Pillar ◽  
Fine Pitch ◽  
Low K

The electromigration behavior of 80μm bump pitch C2 (Chip Connection) interconnection is studied and discussed. C2 is a peripheral ultra fine pitch flip chip interconnection technique with solder capped Cu pillar bumps formed on Al pads that are commonly used in wirebonding technique. It allows us an easy control of the space between dies and substrates simply by varying the Cu pillar height. Since the control of the collapse of the solder bumps is not necessary, the technology is called the “C2 (Chip Connection)”. C2 bumps are connected to OSP surface treated Cu substrate pads on an organic substrate by reflow with no-clean process, hence the C2 is a low cost ultra fine pitch flip chip interconnection technology. The reliability tests on the C2 interconnection including thermal cycle tests and thermal humidity bias tests have been performed previously. However the reliability against electromigration for such small flip chip interconnections is yet more to investigate. The electromigration tests were performed on 80μm bump pitch C2 flip chip interconnections. The interconnections with two different solder materials were tested: Sn-2.5Ag and Sn100%. The effect of Ni layers electroplated onto the Cu pillar bumps on electromigration phenomena is also studied. From the cross-sectional analyses of the C2 joints after the tests, it was found that the presence of intermetallic compound (IMC) layers reduces the atomic migration of Cu atoms into Sn solder. The analyses also showed that the Ni layers are effective in reducing the migration of Cu atoms into solder. In the C2 joints, the under bump metals (UBMs) are formed by sputtered Ti/Cu layers. The electro-plated Cu pillar height is 45μm and the solder height is 25μm for 80μm bump pitch. The die size is 7.3-mm-square and the organic substrate is 20-mm-square with a 4 layer-laminated prepreg with thickness of 310μm. The electromigration test conditions ranged from 7 to 10 kA/cm2 with temperature ranging from 125 to 170°C. Intermetallic compounds (IMCs) were formed prior to the test by aging process of 2,000hours at 150°C. We have studied the effect of IMC layers on electromigration induced phenomena in C2 flip chip interconnections on organic substrates. The study showed that the IMC layers in the C2 joints formed by aging process can act as barrier layers to prevent Cu atoms from diffusing into Sn solder. Our results showed potential for achieving electromigration resistant joints by IMC layer formation. The FEM simulation results show that the current densities in the Cu pillar and the solder decrease with increasing Cu pillar height. However an increase in Cu pillar height also leads to an increase in low-k stress. It is important to design the Cu pillar structure considering both the electromigration performance and the low-k stress reduction.

A Heterogeneous Array of Off-Chip Interconnects for Optimum Mechanical and Electrical Performance

2007 ◽  
Vol 129 (4) ◽  
pp. 460-468 ◽  
Author(s):  
Karan Kacker ◽  
Thomas Sokol ◽  
Wansuk Yun ◽  
Madhavan Swaminathan ◽  
Suresh K. Sitaraman
Keyword(s):  
Flip Chip ◽  
Dielectric Material ◽  
Coefficient Of Thermal Expansion ◽  
Semiconductor Industry ◽  
Organic Substrate ◽  
Electrical Performance ◽  
Integrative Approach ◽  
Wafer Level ◽  
Target Values ◽  
Low K

Demand for off-chip bandwidth has continued to increase. It is projected by the Semiconductor Industry Association in their International Technology Roadmap for Semiconductors that by the year 2015, the chip-to-substrate area-array input-output interconnects will require a pitch of 80 μm. Compliant off-chip interconnects show great potential to address these needs. G-Helix is a lithography-based electroplated compliant interconnect that can be fabricated at the wafer level. G-Helix interconnects exhibit excellent compliance in all three orthogonal directions, and can accommodate the coefficient of thermal expansion (CTE) mismatch between the silicon die and the organic substrate without requiring an underfill. Also, these compliant interconnects are less likely to crack or delaminate the low-k dielectric material in current and future integrated circuits. The interconnects are potentially cost effective because they can be fabricated in batch at the wafer level and using conventional wafer fabrication infrastructure. In this paper, we present an integrative approach, which uses interconnects with varying compliance and thus varying electrical performance from the center to the edge of the die. Using such a varying geometry from the center to the edge of the die, the system performance can be tailored by balancing electrical requirements against thermomechanical reliability concerns. The test vehicle design to assess the reliability and electrical performance of the interconnects is also presented. Preliminary fabrication results for the integrative approach are presented and show the viability of the fabrication procedure. The results from reliability experiments of helix interconnects assembled on an organic substrate are also presented. Initial results from the thermal cycling experiments are promising. Results from mechanical characterization experiments are also presented and show that the out-of-plane compliance exceeds target values recommended by industry experts. Finally, through finite element analysis simulations, it is demonstrated that the die stresses induced by the compliant interconnects are an order of magnitude lower than the die stresses in flip chip on board (FCOB) assemblies, and hence the compliant interconnects are not likely to crack or delaminate low-k dielectric material.

Sign in / Sign up

Export Citation Format

Share Document