Study on Sn-2.3Ag Electroplated Solder Bump Properties Fabricated by Different Plating and Reflow Conditions

2007 ◽  
Author(s):  
C. K. Hsiung ◽  
C. A. Chang ◽  
Z. H. Tzeng ◽  
C. S. Ho ◽  
F. L. Chien
Keyword(s):  
Solder Bump

The Use of Precision Selective Area Milling for Failure Analysis of Flip-Chip Packages

2002 ◽  
Author(s):  
George F. Gaut
Keyword(s):  
Failure Analysis ◽  
Flip Chip ◽  
Solder Bump ◽  
Selective Area ◽  
Fill Material ◽  
Solder Bumps ◽  
Time Required

Abstract Access to the solder bump and under-fill material of flip-chip devices has presented a new problem for failure analysts. The under-fill and solder bumps have also added a new source for failure causes. A new tool has become available that can reduce the time required to analyze this area of a flip-chip package. By using precision selective area milling it is possible to remove material (die or PCB) that will allow other tools to expose the source of the failure.

Quantitative Evaluation of Voids in Lead Free Solder Joints

2015 ◽  
Vol 772 ◽  
pp. 284-289 ◽  
Author(s):  
Sabuj Mallik ◽  
Jude Njoku ◽  
Gabriel Takyi
Keyword(s):  
Solder Bump ◽  
Solder Joints ◽  
Void Formation ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
X Ray ◽  
Size And Shape ◽  
Solder Bumps ◽  
Free Solder

Voiding in solder joints poses a serious reliability concern for electronic products. The aim of this research was to quantify the void formation in lead-free solder joints through X-ray inspections. Experiments were designed to investigate how void formation is affected by solder bump size and shape, differences in reflow time and temperature, and differences in solder paste formulation. Four different lead-free solder paste samples were used to produce solder bumps on a number of test boards, using surface mount reflow soldering process. Using an advanced X-ray inspection system void percentages were measured for three different size and shape solder bumps. Results indicate that the voiding in solder joint is strongly influenced by solder bump size and shape, with voids found to have increased when bump size decreased. A longer soaking period during reflow stage has negatively affectedsolder voids. Voiding was also accelerated with smaller solder particles in solder paste.

Defect Detection of Flip Chip Solder Bumps Through Local Temporal Coherence Analysis of Laser Ultrasound Signals

2007 ◽  
Author(s):  
Jin Yang ◽  
Charles Ume
Keyword(s):  
Defect Detection ◽  
Flip Chip ◽  
Solder Bump ◽  
Temporal Coherence ◽  
Coherence Analysis ◽  
Laser Ultrasound ◽  
Surface Mount ◽  
Flip Chips ◽  
Solder Bumps ◽  
Ultrasound Signals

Microelectronics packaging technology has evolved from through-hole and bulk configuration to surface-mount and small-profile ones. In surface mount packaging, such as flip chips, chip scale packages (CSP), and ball grid arrays (BGA), chips/packages are attached to the substrates or printed wiring boards (PWB) using solder bump interconnections. Solder bumps, which are hidden between the device and the substrate/board, are no longer visible for inspection. A novel solder bump inspection system has been developed using laser ultrasound and interferometric techniques. This system has been successfully applied to detect solder bump defects including missing, misaligned, open, and cracked solder bumps in flip chips, and chip scale packages. This system uses a pulsed Nd:YAG laser to induce ultrasound in the thermoelastic regime and the transient out-of-plane displacement response on the device surface is measured using the interferometric technique. In this paper, local temporal coherence (LTC) analysis of laser ultrasound signals is presented and compared to previous signal processing methods, including Error Ratio and Correlation Coefficient. The results show that local temporal coherence analysis increases measurement sensitivity for inspecting solder bumps in packaged electronic devices. Laser ultrasound inspection results are also compared with X-ray and C-mode Scanning Acoustic Microscopy (CSAM) results. In particular, this paper discusses defect detection for a 6.35mm×6.35mm×0.6mm PB18 flip chip and a flip chip (SiMAF) with 24 lead-free solder bumps. These two flip chip specimens are both non-underfilled.

Direct Solder Bump Formation Technique on Al Pad and Its High Reliability

1992 ◽  
Vol 31 (Part 1, No. 3) ◽  
pp. 761-767 ◽  
Author(s):  
Toshinori Ogashiwa ◽  
Hideyuki Akimoto ◽  
Hiroyuki Shigyo ◽  
Yoshihiro Murakami ◽  
Akihisa Inoue ◽  
...  
Keyword(s):  
Solder Bump ◽  
High Reliability ◽  
Formation Technique

Precise Quantitative Evaluation of Nano-Ordered Intermetallic Compounds in Sn-3.0Ag-0.5Cu Lead-Free Solder Bump by Using TEM

2008 ◽  
Vol 47-50 ◽  
pp. 907-911
Author(s):  
Chang Woo Lee ◽  
Y.S. Shin ◽  
J.H. Kim
Keyword(s):  
Intermetallic Compounds ◽  
Flip Chip ◽  
Solder Bump ◽  
Lead Free Solder ◽  
Growth Behaviour ◽  
Sic Particles ◽  
Imcs Growth ◽  
Ordered Intermetallic ◽  
Free Solder ◽  
The One

The growth behaviour of the intermetallic compounds (IMCs) in Pb-free solder bump is investigated. The Pb-free micro-bump, Sn-50%Bi, was fabricated by binary electroplating for flip-chip bond. The diameter of the bump is about 506m and the height is about 60 6m. In order to increase the reliability of the bonding, it is necessary to protect the growth of the IMCs in interface between Cu pad and the solder bump. For control of IMCs growth, SiC particles were distributed in the micro-solder bump during electroplating. The thickness of the IMCs in the interface was estimated by FE-SEM, EDS, XRF and TEM. From the results, The IMCs were found as Cu6Sn5 and Cu3Sn. The thickness of the IMCs decreases with increase the amount of SiC particles until 4 g/cm2. The one candidate of the reasons is that the SiC particles could decrease the area which be reacted between the solder and Cu layer. And another candidate is that the particle can make to difficult inter-diffusion within the interface.

Interfacial Reaction of Electroless Ni-P Plating with Sn-3.5Ag (-Co) Solder

2008 ◽  
Vol 580-582 ◽  
pp. 243-246 ◽  
Author(s):  
Hiroshi Nishikawa ◽  
Akira Komatsu ◽  
Tadashi Takemoto
Keyword(s):  
Intermetallic Compound ◽  
Interfacial Reaction ◽  
Fracture Mode ◽  
Joint Strength ◽  
Solder Bump ◽  
Solder Joints ◽  
Pull Strength ◽  
Electroless Ni

The reaction between Sn-Ag (-Co) solder and electroless Ni-P plating was investigated in order to clarify the effect of the addition of Co to Sn-Ag solder on the formation of intermetallic compound (IMC) at the interface and the joint strength at the interface. Sn-Ag-Co solder was specially prepared. The results show that there is little effect of the addition of Co to the Sn-Ag solder on the IMC formation and the thickness of the IMC at the interface. For the pull strength of the solder bump joint, the addition of Co to the solder didn’t strongly affect the pull strength of the solder joints, but it affected the fracture mode of the solder joints.

Sign in / Sign up

Export Citation Format

Share Document