Analytical Switching Model of a 1200V SiC MOSFET in a High-voltage, High-frequency Pulsed Power Converter for Plasma Generation

2019 ◽  
Author(s):  
Qunfang Wu ◽  
Mengqi Wang ◽  
Weiyang Zhou ◽  
Guanliang Liu ◽  
Xiaoming Wang ◽  
...  
Keyword(s):  
High Voltage ◽  
High Frequency ◽  
Power Converter ◽  
Pulsed Power ◽  
Plasma Generation ◽  
Switching Model

scholarly journals Analytical Switching Model of a 1200V SiC MOSFET in a High-Frequency Series Resonant Pulsed Power Converter for Plasma Generation

IEEE Access ◽  
2019 ◽  
Vol 7 ◽  
pp. 99622-99632 ◽  
Author(s):  
Qunfang Wu ◽  
Mengqi Wang ◽  
Weiyang Zhou ◽  
Xiaoming Wang ◽  
Guanliang Liu ◽  
...  
Keyword(s):  
High Frequency ◽  
Power Converter ◽  
Pulsed Power ◽  
Plasma Generation ◽  
Switching Model ◽  
Series Resonant

scholarly journals FFT Analysis of a Series Loaded Resonant Converter-Based Power Supply for Pulsed Power Applications

2008 ◽  
Vol 2008 ◽  
pp. 1-5
Author(s):  
R. B. Jadeja ◽  
S. A. Kanitkar ◽  
Anurag Shyam
Keyword(s):  
Power System ◽  
High Voltage ◽  
Power Supply ◽  
High Frequency ◽  
Power Converter ◽  
Pulsed Power ◽  
Pulse Power ◽  
New Family ◽  
High Frequency Transformer ◽  
Input Source

An impulse power supply has been designed, simulated, and tested in order to feed the primary of a high-frequency transformer. Pulse power system has been widely used for plasma applications. The operational principle of the pulse power system is that the energy from the input source is stored in the capacitor bank device through a dc-dc converter. Then, when a discharging signal is given, the stored energy is released to the load. The new family of ZCS converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The power converter can achieve zero switching with the aid of high-frequency transformer. The device is capable of charging a 0.1 μF capacitor up to 5 kV which accounts for a charging power of 5 kJ/s. The novel control algorithm is achieved which eminently considers the nonlinear control characteristics of impulse power supply. The required charging voltage, together with the constraint on the charging time, translates into a required maximum power of 10 kW reduced in this initial version to 5 kW. The difficulty to reliably control such a power at the high-voltage side practically forbids any approach featuring a more or less stabilized DC high-voltage to be generated from a conventional 50 Hz transformer through rectification.

Analysis and Design of 3.3 kV IGBT Based Three-Level DC/DC Converter with High-Frequency Isolation and Current Doubler Rectifier

2009 ◽  
Vol 25 (25) ◽  
pp. 103-108
Author(s):  
Dmitri Vinnikov ◽  
Tanel Jalakas ◽  
Indrek Roasto
Keyword(s):  
High Voltage ◽  
High Frequency ◽  
Power Converter ◽  
Rolling Stock ◽  
Analysis And Design ◽  
Auxiliary Power ◽  
Igbt Modules ◽  
Isolation Transformer ◽  
New Generation ◽  
Generation Power

Analysis and Design of 3.3 kV IGBT Based Three-Level DC/DC Converter with High-Frequency Isolation and Current Doubler RectifierThe paper presents the findings of a R&D project connected to the development of auxiliary power supply (APS) for the high-voltage DC-fed rolling stock applications. The aim was to design a new-generation power converter utilizing high-voltage IGBT modules, which can outpace the predecessors in terms of power density, i.e. to provide more power for smaller volumetric space. The topology proposed is 3.3 kV IGBT-based three-level neutral point clamped (NPC) half-bridge with high-frequency isolation transformer and current doubler rectifier that fulfils all the targets imposed by the designers. Despite an increased component count the proposed converter is very simple in design and operation. The paper provides an overview of the design with several recommendations and guidelines. Moreover, the simulation and experimental results are discussed and the performance evaluation of the proposed converter is presented.

Development of High Voltage High Frequency Resonant Inverter Power Supply for Atmospheric Surface Glow Barrier Discharges

2005 ◽  
Vol 107 ◽  
pp. 81-86 ◽  
Author(s):  
M. Nisoa ◽  
D. Srinoum ◽  
P. Kerdthongmee
Keyword(s):  
High Voltage ◽  
Power Supply ◽  
High Frequency ◽  
Output Voltage ◽  
Pulse Width Modulation ◽  
Power Converter ◽  
Maximum Output ◽  
Resonant Inverter ◽  
Resonant Inductor ◽  
Barrier Discharges

High-voltage high-frequency power supply using voltage-fed load resonant inverter with a series-compensated resonant inductor has been developed for efficient atmospheric surface glow barrier discharges(ASGBD). It produces a controllable frequency and sinusoidal alternating voltage output. The maximum output voltage is about 6 kV peak to peak. Resonant power converter can be tune easily to the resonant frequency of the load. Operating frequency varies according to the load and voltage level typically in the range of 10 kHz and 1 MHz range. The output voltage is controlled by using pulse width modulation technique. The power supply developed in this paper is applied successfully for ozoniser that can produce high concentrate ozone by using ASGBD for agricultural industry applications.

scholarly journals Construction of a power electronic source for cold plasma generation

2019 ◽  
Vol 20 (4) ◽  
pp. 1-12 ◽  
Author(s):  
Roberto Carlos Martínez Montejano ◽  
Carlos Miguel Castillo Escandón ◽  
Víctor Esteban Espinoza López ◽  
Isaac Campos Cantón ◽  
María Guadalupe Neira Velázquez ◽  
...  
Keyword(s):  
Electric Field ◽  
Dielectric Barrier Discharge ◽  
High Voltage ◽  
High Frequency ◽  
Barrier Discharge ◽  
Strong Electric Field ◽  
Power Electronic ◽  
Dielectric Barrier ◽  
Plasma Generation ◽  
Electronic Source

This paper presents the development of a high voltage and high-frequency power electronics source, for plasma generation, at atmospheric pressure and vacuum, using helium and air as working gases. The source design consists of an inductive (L) full bridge series resonant inverter at high frequency, where the control implemented allows varying duty cycle and frequency. Plasma generation is made by high voltage with the power signal applied on two electrodes, which provides a strong electric field that excites, and thus, ionize helium particles or air particles. The power electronic source operation was tested in different plasma reactor configurations (dielectric barrier discharge, double dielectric barrier discharge, and jet type discharge). The developed power electronics source shows a correct performance and generate a strong electric field to achieve the plasma discharges desired.

Sign in / Sign up

Export Citation Format

Share Document