A high-resolution silicon monolithic nozzle array for inkjet printing

1997 ◽  
Vol 44 (9) ◽  
pp. 1401-1409 ◽  
Author(s):  
Jingkuang Chen ◽  
K.D. Wise
Nanoscale ◽  
2016 ◽  
Vol 8 (39) ◽  
pp. 17113-17121 ◽  
Author(s):  
S.-Y. Kim ◽  
K. Kim ◽  
Y. H. Hwang ◽  
J. Park ◽  
J. Jang ◽  
...  

Lab on a Chip ◽  
2021 ◽  
Author(s):  
Eiyong Park ◽  
Sungjoon Lim

RF electronics is inkjet-printed directly onto a 3D printed microfluidic structure using surface modification for the high conductivity, high resolution, and enhanced the interaction between a RF part and a fluid material.


2020 ◽  
Vol 8 (43) ◽  
pp. 15219-15223
Author(s):  
Jing Zhang ◽  
Bowen Geng ◽  
Shuming Duan ◽  
Congcong Huang ◽  
Yue Xi ◽  
...  

A top-contact, sub-5 μm resolution OFET is realized using inkjet printed electrodes with different F4-TCNQ doping concentrations.


Science ◽  
2000 ◽  
Vol 290 (5499) ◽  
pp. 2123-2126 ◽  
Author(s):  
H. Sirringhaus ◽  
T. Kawase ◽  
R. H. Friend ◽  
T. Shimoda ◽  
M. Inbasekaran ◽  
...  

2018 ◽  
Vol 5 (1) ◽  
Author(s):  
Jack Zhou ◽  
Dajing Gao ◽  
Donggang Yao ◽  
Steven K. Leist ◽  
Yifan Fei

The purpose of this paper is to review the mechanisms of electrohydrodynamic (EHD) phenomenon. From this review, researchers and students can learn principles and development history of EHD. Significant progress has been identified in research and development of EHD high-resolution deposition as a direct additive manufacturing method, and more effort will be driven to this direction soon. An introduction is given about current trend of additive manufacturing and advantages of EHD inkjet printing. Both theoretical models and experiment approaches about the formation of cone, development of cone-jet transition and stability of jet are presented. The formation of a stable cone-jet is the key factor for precision EHD printing which will be discussed. Different scaling laws can be used to predict the diameter of jet and emitted current in different parametrical ranges. The information available in this review builds a bridge between EHD phenomenon and three-dimensional high-resolution inkjet printing.


Materials ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2277 ◽  
Author(s):  
Mavuri ◽  
Mayes ◽  
Alexander

Printed electronics (PE) technology shows huge promise for the realisation of low-cost and flexible electronics, with the ability to pattern heat- or pressure-sensitive materials. In future developments of the PE market, the ability to produce highly conductive, high-resolution patterns using low-cost and roll-to-roll processes, such as inkjet printing, is a critical technology component for the fabrication of printed electronics and displays. Here, we demonstrate inkjet printing of polyacrylic acid (PAA) capped silver nanoparticle dispersions onto paper for high-conductivity electronic interconnects. We characterise the resulting print quality, feature geometry and electrical performance of inkjet patterned features and demonstrate the high-resolution printing, sub-100 micron feature size, of silver nanoparticle materials onto flexible paper substrate. Printed onto photo-paper, these materials then undergo chemically triggered sintering on exposure to chloride contained in the paper. We investigated the effect of substrate temperature on the properties of printed silver material from room temperature to 50 °C. At room temperature, the resistivity of single layer printed features, of average thickness of 500 nm and width 85 µm, was found to be 2.17 × 10−7 Ω·m or 13 times resistivity of bulk silver (RBS). The resistivity initially decreased with an increase in material thickness, when achieved by overprinting successive layers or by decreasing print pitch, and a resistivity of around 10 times RBS was observed after overprinting two times at pitch 75 µm and with single pass print pitch of between 60 and 80 µm, resulting in line thickness up to 920 nm. On further increases in thickness the resistivity increased and reached 27 times RBS at print pitch of 15 µm. On moderate heating of the substrate to 50 °C, more compact silver nanoparticle films were formed, reducing thickness to 200 nm from a single pass print, and lower material resistivity approaching five times RBS was achieved.


2014 ◽  
Vol 24 (5) ◽  
pp. 055008 ◽  
Author(s):  
Guo-Shin Lu ◽  
Po-Chin You ◽  
Kai-Lun Lin ◽  
Chien-Chong Hong ◽  
Tong-Miin Liou

Nanomaterials ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1538
Author(s):  
Valeriia O. Neterebskaia ◽  
Anna O. Goncharenko ◽  
Sofia M. Morozova ◽  
Denis S. Kolchanov ◽  
Alexandr V. Vinogradov

This study is devoted to the development of photonic patterns based on polystyrene spheres (PSS) incorporated in chitosan hydrogels by inkjet printing. Using this method, high-resolution encrypted images that became visible only in high humidity were obtained. Inks based on PSS with carboxylic groups on the surface were made, and their rheological parameters (viscosity, surface tension, and ζ-potential) were optimized according to the Ohnesorge theory. The obtained value of the ζ-potential indicated the stability of the synthesized colloidal inks. The dependences of the printing parameters on the concentration of ethylene glycol in PSS dispersion, the drop spacing, the shape of the printed pattern, waveform, the temperature of the printing process, and the degree of ordering of the PSS-based photonic crystal were investigated. The scanning electronic microscope (SEM) images confirmed that the optimal self-organization of PSS was achieved at the following values of 0.4% weight fraction (wt%) carboxylic groups, the drop spacing of 50 μm, and the temperature of the printing table of 25 °C. High-resolution microstructures were obtained by drop-on-demand printing with a deposited drophead diameter of 21 μm and an accuracy of ±2 μm on silicon and glass substrates. The deposition of chitosan-based hydrogels on the obtained polystyrene photonic crystals allowed reversibly changing the order of the diffraction lattice of the photonic crystal during the swelling of the hydrogel matrix, which led to a quick optical response in the daylight. The kinetics of the appearance of the optical response of the obtained coating were discussed. The simplicity of production, the speed of image appearance, and the ability to create high-resolution patterns determine the potential applications of the proposed systems as humidity sensors or anticounterfeiting coatings.


Sign in / Sign up

Export Citation Format

Share Document