High-resolution conductive patterns fabricated by inkjet printing and spin coating on wettability-controlled surfaces

2016 ◽  
Vol 616 ◽  
pp. 238-246 ◽  
Author(s):  
Changkyu Lee ◽  
Byung Ju Kang ◽  
Je Hoon Oh
Nanoscale ◽  
2016 ◽  
Vol 8 (39) ◽  
pp. 17113-17121 ◽  
Author(s):  
S.-Y. Kim ◽  
K. Kim ◽  
Y. H. Hwang ◽  
J. Park ◽  
J. Jang ◽  
...  

Lab on a Chip ◽  
2021 ◽  
Author(s):  
Eiyong Park ◽  
Sungjoon Lim

RF electronics is inkjet-printed directly onto a 3D printed microfluidic structure using surface modification for the high conductivity, high resolution, and enhanced the interaction between a RF part and a fluid material.


2018 ◽  
Vol 39 (10) ◽  
pp. 1451-1457
Author(s):  
陈文斌 CHEN Wen-bin ◽  
郭文瑞 GUO Wen-rui ◽  
牟婉莹 MOU Wan-ying ◽  
杜真真 DU Zhen-zhen ◽  
唐鹏宇 TANG Peng-yu ◽  
...  

2020 ◽  
Vol 8 (43) ◽  
pp. 15219-15223
Author(s):  
Jing Zhang ◽  
Bowen Geng ◽  
Shuming Duan ◽  
Congcong Huang ◽  
Yue Xi ◽  
...  

A top-contact, sub-5 μm resolution OFET is realized using inkjet printed electrodes with different F4-TCNQ doping concentrations.


1997 ◽  
Vol 44 (9) ◽  
pp. 1401-1409 ◽  
Author(s):  
Jingkuang Chen ◽  
K.D. Wise

Science ◽  
2000 ◽  
Vol 290 (5499) ◽  
pp. 2123-2126 ◽  
Author(s):  
H. Sirringhaus ◽  
T. Kawase ◽  
R. H. Friend ◽  
T. Shimoda ◽  
M. Inbasekaran ◽  
...  

2018 ◽  
Vol 5 (1) ◽  
Author(s):  
Jack Zhou ◽  
Dajing Gao ◽  
Donggang Yao ◽  
Steven K. Leist ◽  
Yifan Fei

The purpose of this paper is to review the mechanisms of electrohydrodynamic (EHD) phenomenon. From this review, researchers and students can learn principles and development history of EHD. Significant progress has been identified in research and development of EHD high-resolution deposition as a direct additive manufacturing method, and more effort will be driven to this direction soon. An introduction is given about current trend of additive manufacturing and advantages of EHD inkjet printing. Both theoretical models and experiment approaches about the formation of cone, development of cone-jet transition and stability of jet are presented. The formation of a stable cone-jet is the key factor for precision EHD printing which will be discussed. Different scaling laws can be used to predict the diameter of jet and emitted current in different parametrical ranges. The information available in this review builds a bridge between EHD phenomenon and three-dimensional high-resolution inkjet printing.


Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 1904
Author(s):  
Aggeliki Karavioti ◽  
Dimitris A. Chalkias ◽  
Giannis Katsagounos ◽  
Argyroula Mourtzikou ◽  
Alexandros N. Kalarakis ◽  
...  

Up until now, the vast majority of perovskite solar cells (PSCs) have relied on the spin-coating of perovskite precursor solution under inert fully controlled conditions, with the performance of solar cells that are developed by alternative techniques and under an ambient atmosphere to lag far behind. This impedes the technology transfer from the laboratory to industrial large-scale production; thus, the investigation of new scalable techniques should be thoroughly considered. The present work constitutes one of the few investigations on the application of inkjet-printing as an advanced alternative technique to the conventional spin-coating technique used for the fabrication of fully ambient air-processed perovskite absorbent layers for carbon-based hole transport layer-free PSCs. A systematic study of the characteristics of the perovskite material and solar cells indicated that the coffee-ring effect combined with poor ink penetration into the mesoporous network of the anode semiconductor were the main reasons for obtaining poor perovskite structure morphology and lower PSC performance by inkjet-printing, which arises from a lower internal quantum efficiency and an increased charge transfer and recombination rate. On the other hand, the crystallinity and optical characteristics of the materials obtained by the compared techniques did not differ considerably, while small differences were observed in the hysteretic behavior and long-term stability of the solar cells.


Materials ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2277 ◽  
Author(s):  
Mavuri ◽  
Mayes ◽  
Alexander

Printed electronics (PE) technology shows huge promise for the realisation of low-cost and flexible electronics, with the ability to pattern heat- or pressure-sensitive materials. In future developments of the PE market, the ability to produce highly conductive, high-resolution patterns using low-cost and roll-to-roll processes, such as inkjet printing, is a critical technology component for the fabrication of printed electronics and displays. Here, we demonstrate inkjet printing of polyacrylic acid (PAA) capped silver nanoparticle dispersions onto paper for high-conductivity electronic interconnects. We characterise the resulting print quality, feature geometry and electrical performance of inkjet patterned features and demonstrate the high-resolution printing, sub-100 micron feature size, of silver nanoparticle materials onto flexible paper substrate. Printed onto photo-paper, these materials then undergo chemically triggered sintering on exposure to chloride contained in the paper. We investigated the effect of substrate temperature on the properties of printed silver material from room temperature to 50 °C. At room temperature, the resistivity of single layer printed features, of average thickness of 500 nm and width 85 µm, was found to be 2.17 × 10−7 Ω·m or 13 times resistivity of bulk silver (RBS). The resistivity initially decreased with an increase in material thickness, when achieved by overprinting successive layers or by decreasing print pitch, and a resistivity of around 10 times RBS was observed after overprinting two times at pitch 75 µm and with single pass print pitch of between 60 and 80 µm, resulting in line thickness up to 920 nm. On further increases in thickness the resistivity increased and reached 27 times RBS at print pitch of 15 µm. On moderate heating of the substrate to 50 °C, more compact silver nanoparticle films were formed, reducing thickness to 200 nm from a single pass print, and lower material resistivity approaching five times RBS was achieved.


Sign in / Sign up

Export Citation Format

Share Document