Effect of non- α -cluster projectile on incomplete-fusion dynamics: Experimental study of the N14+Ta181 system

2021 ◽  
Vol 104 (3) ◽  
Author(s):  
M. Shariq Asnain ◽  
Mohd. Shuaib ◽  
Ishfaq Majeed ◽  
Manoj Kumar Sharma ◽  
Vijay R. Sharma ◽  
...  
Keyword(s):  
Experimental Study ◽  
Incomplete Fusion ◽  
Cluster Projectile

scholarly journals Experimental study of cross sections in theC12+Al27system at≈3–7MeV/nucleonrelevant to the incomplete fusion process

2015 ◽  
Vol 91 (2) ◽  
Author(s):  
Manoj Kumar Sharma ◽  
Abhishek Yadav ◽  
Vijay Raj Sharma ◽  
Devendra P. Singh ◽  
Pushendra P. Singh ◽  
...  
Keyword(s):  
Experimental Study ◽  
Cross Sections ◽  
Fusion Process ◽  
Incomplete Fusion

Experimental study of incomplete fusion reactions in theO16+Te130system below 6 MeV/nucleon

2014 ◽  
Vol 89 (2) ◽  
Author(s):  
Devendra P. Singh ◽  
Vijay R. Sharma ◽  
Abhishek Yadav ◽  
Pushpendra P. Singh ◽  
Unnati ◽  
...  
Keyword(s):  
Experimental Study ◽  
Incomplete Fusion ◽  
Fusion Reactions

Effect of neutron excess in the entrance channel on the O18+Nb93 system: An experimental study relevant to incomplete-fusion dynamics

2021 ◽  
Vol 103 (3) ◽  
Author(s):  
Avinash Agarwal ◽  
Anuj Kumar Jashwal ◽  
Munish Kumar ◽  
S. Prajapati ◽  
Sunil Dutt ◽  
...  
Keyword(s):  
Experimental Study ◽  
Entrance Channel ◽  
Incomplete Fusion ◽  
Neutron Excess

Experimental study on the restoration from a tilt-azimuth series for improvement in resolution

1995 ◽  
Vol 53 ◽  
pp. 636-637
Author(s):  
Norio Baba ◽  
Norihiko Ichise ◽  
Syunya Watanabe
Keyword(s):  
Experimental Study ◽  
Spherical Aberration ◽  
Incident Beam ◽  
Optical Parameters ◽  
Beam Tilting ◽  
Illumination Method ◽  
Restoration Method ◽  
Illumination Mode

The tilted beam illumination method is used to improve the resolution comparing with the axial illumination mode. Using this advantage, a restoration method of several tilted beam images covering the full azimuthal range was proposed by Saxton, and experimentally examined. To make this technique more reliable it seems that some practical problems still remain. In this report the restoration was attempted and the problems were considered. In our study, four problems were pointed out for the experiment of the restoration. (1) Accurate beam tilt adjustment to fit the incident beam to the coma-free axis for the symmetrical beam tilting over the full azimuthal range. (2) Accurate measurements of the optical parameters which are necessary to design the restoration filter. Even if the spherical aberration coefficient Cs is known with accuracy and the axial astigmatism is sufficiently compensated, at least the defocus value must be measured. (3) Accurate alignment of the tilt-azimuth series images.

Selective Corrosion of brazed joint between BNi-2 filler metal and stainless steel 316

1996 ◽  
Vol 54 ◽  
pp. 218-219
Author(s):  
H. S. Kim ◽  
R. U. Lee
Keyword(s):  
Stainless Steel ◽  
Filler Metal ◽  
Surface Preparation ◽  
Optical Microscope ◽  
Heating Element ◽  
Incomplete Fusion ◽  
Atmospheric Conditions ◽  
Leak Test ◽  
High Temperature Side ◽  
Inconel 600

A heating element/electrical conduit assembly used in the Orbiter Maneuvering System failed a leak test during a routine refurbishment inspection. The conduit, approximately 100 mm in length and 12 mm in diameter, was fabricated from two tubes and braze-joined with a sleeve. The tube on the high temperature side (heating element side) and the sleeve were made of Inconel 600 and the other tube was stainless steel (SS) 316. For the filler metal, a Ni-Cr-B brazing alloy per AWS BNi-2, was used. A Helium leak test spotted the leak located at the joint between the sleeve and SS 316 tubing. This joint was dissected, mounted in a plastic mold, polished, and examined with an optical microscope. Debonding of the brazed surfaces was noticed, more pronounced toward the sleeve end which was exposed to uncontrolled atmospheric conditions intermittently. Initially, lack of wetting was suspected, presumably caused by inadequate surface preparation or incomplete fusion of the filler metal. However, this postulation was later discarded based upon the following observations: (1) The angle of wetting between the fillet and tube was small, an indication of adequate wetting, (2) the fillet did not exhibit a globular microstructure which would be an indication of insufficient melting of the filler metal, and (3) debonding was intermittent toward the midsection of the sleeve.

An Experimental Study of Some Properties of Stuttered Words

1962 ◽  
Vol 5 (4) ◽  
pp. 387-394 ◽  
Author(s):  
Bruce Quarrington ◽  
Jerome Conway ◽  
Nathan Siegel
Keyword(s):  
Experimental Study

Experimental study of total body washout employing extracorporeal circulation and hypothermia

1974 ◽  
Vol 126 (2) ◽  
pp. 243-248
Author(s):  
A WAKABAYASHI ◽  
T KUBO ◽  
K CHARNEY ◽  
Y NAKAMURA ◽  
J CONNOLLY
Keyword(s):  
Experimental Study ◽  
Extracorporeal Circulation ◽  
Total Body

Gastric Freezing: An Experimental Study

1963 ◽  
Vol 45 (3) ◽  
pp. 374-383 ◽  
Author(s):  
Donald C. McIlrath ◽  
George A. Hallenbeck ◽  
Hubert A. Allen ◽  
Charles V. Mann ◽  
Edward J. Baldes ◽  
...  
Keyword(s):  
Experimental Study
Sign in / Sign up

Export Citation Format

Share Document