Reviewing hook degradation to promote ejection after ingestion by marine fish

2011 ◽  
Vol 62 (10) ◽  
pp. 1237 ◽  
Author(s):  
Shane P. McGrath ◽  
Paul A. Butcher ◽  
Matt K. Broadhurst ◽  
Stuart C. Cairns
Keyword(s):  
Carbon Steel ◽  
Marine Fish ◽  
Quantitative Data ◽  
Wire Diameter ◽  
Wire Material ◽  
Technical Factors ◽  
The Wire ◽  
Negative Impacts ◽  
The Individual

A widely recommended strategy for releasing fish that have ingested hooks is to simply cut the line. The utility of this approach is based on the premise that the individual will eventually eject the hook following sufficient oxidation. However, few quantitative data are available describing the mechanisms affecting hook decay. We addressed this issue by testing the independence of various technical factors on the degradation of 828 hooks comprising 23 designs (absolute sizes 227–611 mm2) after protracted submersion in seawater. Twelve replicates of each hook were destructively assessed for compression and tensile strengths (using a force gauge) and 24 replicates were weighed, photographed and submersed in seawater. After submersion for 8 and 28 days, 12 replicate hooks were removed, re-photographed, re-weighed and tested for compression and tensile strengths to provide indices of decay. Hook degradation was mainly affected by the wire material and diameter and could be significantly promoted by choosing carbon steel designs, either with a wire diameter of ≤0.9 mm for the examined sizes or, alternatively, bait-holder barbs (or similar modifications) along the shaft. By rapidly oxidising and weakening after ingestion, such designs could ultimately help to reduce negative impacts of hooks on released fish.

First Order Reversal Curves (FORC) Diagrams of Co Nanowire Arrays

2008 ◽  
Vol 8 (11) ◽  
pp. 5725-5732 ◽  
Author(s):  
M. Ciureanu ◽  
F. Béron ◽  
P. Ciureanu ◽  
R. W. Cochrane ◽  
D. Ménard ◽  
...  
Keyword(s):  
Wire Diameter ◽  
Nanowire Arrays ◽  
Wire Length ◽  
First Order ◽  
Factors Influencing ◽  
Theoretical Predictions ◽  
Nanoporous Alumina Templates ◽  
The Wire ◽  
The Individual ◽  
Array Geometry

Nanowire arrays of Co and Ni have been obtained by current pulse electrodeposition into nanoporous alumina templates. By adjusting the pH of the bath, the microstructure of the Co wires was tailored, resulting in two types of arrays of crystalline Co—hcp, with c-axis nominally parallel (Co (c∥)), or nominally perpendicular (Co (c⊥)) to the wire. First-order reversal curve (FORC) diagrams provide information on average coercivity of the individual nanowire and the factors influencing the field created in the saturated array by the magnetostatic interactions. The dependences of this field on array geometry (wire length and diameter) and saturation magnetization were found to be in excellent agreement with theoretical predictions from a micromagnetic model. For arrays with lower wire diameter, the average coercivity of the individual wires is systematically higher than the coercivity of the array. The most important difference between the two Co series is in the dependence of the FORC diagrams on the wire diameter, with the Co (c⊥) showing significant pattern changes at large diameters. Two possible sources of those changes are discussed.

CYBERBULLYING PADA MEDIA SOSIAL: Menyoroti Perilaku Cyberbullying Menurut Perspektif Model Konseling Realitas

2020 ◽  
Author(s):  
Darimis Darimis Darimis
Keyword(s):  
Social Relationships ◽  
Choice Theory ◽  
Human Beings ◽  
Important Goal ◽  
Application Procedure ◽  
Negative Impacts ◽  
Use Of The Internet ◽  
The Individual ◽  
Counseling Model ◽  
Real Responsibility

Use of the Internet has changed the paradigm of human beings communicate with one another, especially on social media. Indonesia as one of the highest in the world Facebook users make significant consequences specifically for teenagers. The trend using Facebook by teenagers has created negative impacts that is the rise of cyberbullying.Cyberbullying can significantly influence the lives of teenagers and it can be a huge burden as it can happen for a long period of time. In cyberbullying, there are cyber bullies and cyber victims as individuals involved to make the message as a reference the behavior of cyberbullying. This paper attempts to looking at the perspective of the cyberbullying behavior by reality counseling model, because reality counseling as one of the models of counseling that focuses on behavior now unrealistic and dysfunctional.Reality counseling based on the choice theory, counselee make more effective choices about the development of relational satisfactory with others. The most important goal of therapy is to make people aware of the reality that the real responsibility for her behavior was himself. This counseling can helping the individual reality of cyberbullying offenders realize the consequences of his behavior, responsible, develop positive social relationships through the application procedure techniques WDEP and techniques reality Counseling.

Methods for assessing territory pollution by oil or petroleum product spills

2020 ◽  
pp. 140-146
Author(s):  
S. I. Chelombitko ◽  
V. V. Piven
Keyword(s):  
Oil And Gas ◽  
Radiant Energy ◽  
Petroleum Products ◽  
Individual Characteristics ◽  
Oil And Gas Fields ◽  
Northern Regions ◽  
Negative Impacts ◽  
The Individual ◽  
Destructive Processes ◽  
Gas Fields

During the development of oil and gas fields and transportation of hydrocarbons, the ecology of regions is subject to various negative impacts. The most severe consequences for the environment are caused by accidental spills of oil or petroleum products, which occur due to through damage to pipelines. Polluted territories are subject to mandatory reclamation in accordance with government regulations and industry regulations. However, despite the measures taken by the administrations of the northern regions to increase the rate of reclamation of damaged territories in recent years, there has been a trend of growth of areas contaminated with hydrocarbons.Various remediation technologies that have been tested in warm and temperate climates are not very effective in regions with permafrost. Pollution of the daytime surface with oil or petroleum products leads to an increase in the absorption of the sun's radiant energy, the growth of the seasonal thaw layer and the development of destructive processes for the territory. To achieve a positive effect as a result of rehabilitation measures, it is necessary to take into account the individual characteristics of the territory and the extent of its pollution.

scholarly journals Differential Influences of Teleconnections from the Indian and Pacific Oceans on Rainfall Variability in Southeast Asia

Atmosphere ◽  
2020 ◽  
Vol 11 (9) ◽  
pp. 886
Author(s):  
Abdul Azim Amirudin ◽  
Ester Salimun ◽  
Fredolin Tangang ◽  
Liew Juneng ◽  
Muhamad Zuhairi
Keyword(s):  
Indian Ocean ◽  
Southeast Asia ◽  
El Niño ◽  
El Nino ◽  
Rainfall Variability ◽  
June July August ◽  
Rainfall Patterns ◽  
Negative Impacts ◽  
The Individual ◽  
June July

This study investigates the individual and combined impacts of El Niño and the positive Indian Ocean Dipole (IOD) on the Southeast Asia (SEA) rainfall variability. Using composite and partial correlation techniques, it is shown that both inter-annual events have individually distinct impacts on the SEA rainfall anomaly distribution. The results showed that the impacts of the co-occurrence of El Niño and IOD events are significant compared to the individual effects of pure El Niño or pure IOD. During June-July-August and September-October-November, the individual impacts of the pure El Niño and IOD events are similar but less significant. Both events caused negative impacts over the southern part of SEA during June-July-August (JJA) and propagated northeastward/eastward during September-October-November (SON). Thus, there are significant negative impacts over the southern part of SEA during the co-occurrence of both events. The differential impacts on the anomalous rainfall patterns are due to the changes in the sea surface temperature (SST) surrounding the region. Additionally, the differences are also related to the anomalous regional atmospheric circulations that interact with the regional SST. The anomalous Walker circulation that connects the Indian Ocean and tropical Pacific Ocean also plays a significant role in determining the regional anomalous rainfall patterns.

The Investigation in the Influence of Hardness to Transition Point after Tempering for Boric Carbon Steels

2013 ◽  
Vol 690-693 ◽  
pp. 186-192
Author(s):  
Ho Hua Chung ◽  
Tsong Hsin Chen
Keyword(s):  
Impact Energy ◽  
Carbon Steels ◽  
Material Strength ◽  
Tempering Temperature ◽  
Material Test ◽  
Wire Material ◽  
Steel Material ◽  
The Wire ◽  
The Impact ◽  
Test Fragment

This study concerned the influence of the material strength, ductility and impact energy and the relationship of the broken section profile vs. ductile transition brittle where the steel material was treated under different tempering temperature and hardness. Generally after the steel materials, 10B35 coil wire materials which was generally applied to form screws, was treated by quenching and tempering, its hardness ranged from HRC30 to HRC45. The results showed that the elongation rate beyond 20.4% would be proportional to the impact energy with linear relation, but with reverse proportion to the hardness value. The brittle-tough point of the hardness was set around HRC37 after heat treatment in order to balance the strength and the toughness. In addition, the coil wire materials were analyzed from broken section materials showing good toughness; this represented that the area of the cross section radiation layer due to ductile fracture would largely increase. On the contrary, the wire material test fragment with bad toughness represented that the area of the shear layer due to brittle fracture would largely increase as well. As to that material, if its hardness was greater than or equal to HRC37, that material would have an excellent turning danger from transition. At the same time, when the tempering temperature of the wire steel material was set under 4600C and its corresponding central hardness was about HRC37, the distance between two cementite phase layers suddenly increased. This result leaded to the reason why the wire material test fragment was turned into brittleness from ductility. Therefore, when the fastener was manufactured under tempering treatment, avoiding the tempering brittleness temperature range was necessary.

The Effect of Stand-Off Distance on the Structure and Properties of Zirconium – Carbon Steel Bimetal Produced by Explosion Welding / Wpływ Odległości Blach Na Strukturę I Własności Bimetalu Cyrkon - Stal Wytworzonego Technologią Zgrzewania Wybuchowego

2012 ◽  
Vol 57 (4) ◽  
pp. 1201-1210 ◽  
Author(s):  
M. Prażmowski ◽  
H. Paul
Keyword(s):  
Carbon Steel ◽  
Optical Microscopy ◽  
Longitudinal Section ◽  
Strength Properties ◽  
Strength Distribution ◽  
Explosion Welding ◽  
General Description ◽  
Bond Zone ◽  
Bond Interface ◽  
The Individual

This study focuses on the effect of the stand-off distance between the bonded plates on the properties of zirconium (Zr700) - steel (P355NL2) bimetal produced by explosion welding. Bonding trials were carried out in parallel arrangement at constant detonation velocity. The analyses of microstructural transformations occurring in the bond zone and mechanical properties of the clad were performed for as-bonded welds, i.e. immediately following explosion welding. A general description of the obtained welds was made (height and length of the wave was determined) and the quantitative fraction of the melt zones was calculated along the bond’s length. Using optical microscopy and scanning electron microscopy (SEM) enabled the assessment of the quality of the formed bonds, initial identification of phases and quantitative analysis of the individual phases on the longitudinal section. The microhardness results were used in the analysis of hardening changes at the interface area. The completed research proves the potential to obtain a proper bond for zirconium/carbon steel sheets. A strong effect of the stand-off distance on the strength properties of the fabricated plates was observed, and the ’direction’ of these transformations was pointed out. Optical microscopy and SEM examinations allowed determining the characteristic of the bond interface for diverse stand-off distances. It was established that increasing the stand-off distance between the plates causes the reduction of the melt area along the length of the bond, which improves strength properties of the bimetal. The analysis of the strength distribution performed based on the microhardness measurements showed that the changes occur within the distances up to 500µm from the bond interface and the highest hardening, for both zirconium and steel, is directly at the interface and then successively decreases.

ASSESSMENT OF WOODEN BUILDINGS IN TERMS OF CONSTRUCTION WASTE GENERATION

2020 ◽  
Author(s):  
Marcela Spišáková ◽  
Mária Kozlovská ◽  
Jozef Švajlenka
Keyword(s):  
Negative Impact ◽  
Raw Materials ◽  
Environmental Parameters ◽  
Constructional Material ◽  
Waste Generation ◽  
Construction Waste ◽  
Construction Market ◽  
Negative Impacts ◽  
The Individual ◽  
Wooden Structures

Construction industry creates an environment for people's lives. On the other hand, construction activities have a negative impact on various aspects of the environment. It consumes natural raw materials, significantly contributes to carbon footprint, waste, etc. Appropriate choice of constructional, material, technical, technological and environmental parameters of buildings can partially reduce this negative impacts. By designing, implementing and using wood-based constructions it is possible to reduce the negative impact in the area of construction waste generation. Currently, the construction market offers a large number of construction systems of wooden buildings, which have both strengths and weaknesses. In this paper are identified construction systems of wooden buildings offered on the Slovak construction market. The aim of the paper is a detailed identification of construction waste generation during the realization of particular wooden structures and monitoring of waste generation in production factory (off site) and on construction site (on site) during the construction of wooden buildings. Based on the obtained information, the individual construction systems of wood-based constructions are compared in terms of construction waste generation

scholarly journals Violence in the workplace: awareness and prevention

2003 ◽  
Vol 26 (1) ◽  
pp. 84 ◽  
Author(s):  
Jan Hinson ◽  
Margaret Shapiro
Keyword(s):  
Physical Violence ◽  
Workplace Safety ◽  
Front Line ◽  
Violent Event ◽  
Policy Initiatives ◽  
Occupational Violence ◽  
Negative Impacts ◽  
Violence In The Workplace ◽  
Policy Direction ◽  
The Individual

Occupational violence is of growing interest to both individuals and organisations in the health field.Not surprisingly, staff who work directly on the front line are more vulnerable to episodes of physical violence from the general public. However, violence manifests in a number of ways,and any person in the workplace can experience it at anytime. Occupational violence should be viewed as an event to be identified, understood and managed, with a consequent need to identify types of violence in order to provide policy direction and preventive strategies to enhance workplace safety. Violence cannot be totally prevented but the risk of violence and its negative impacts on the individual can be reduced with carefully considered planning and swift action following a violent event. This paper reports various types of violence, the magnitude of the problem and who is at risk. Policy initiatives are suggested and methods of prevention discussed.

Effect of the Wire Diameter on the Stability of Micro-Scale Ag/AgCl Reference Electrode

2017 ◽  
Vol 164 (14) ◽  
pp. E560-E564 ◽  
Author(s):  
S. Seghir Mechaour ◽  
A. Derardja ◽  
K. Oulmi ◽  
M. J. Deen
Keyword(s):  
Reference Electrode ◽  
Wire Diameter ◽  
Micro Scale ◽  
The Wire ◽  
The Stability

scholarly journals Information storage in permalloy modulated magnetic nanowires

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Guidobeth Sáez ◽  
Pablo Díaz ◽  
Eduardo Cisternas ◽  
Eugenio E. Vogel ◽  
Juan Escrig
Keyword(s):  
Magnetic Material ◽  
Phase Diagram ◽  
Magnetic Fields ◽  
Domain Walls ◽  
Wire Diameter ◽  
Information Storage ◽  
Magnetic Nanowires ◽  
The Wire ◽  
The Stability ◽  
Cylindrical Wire

AbstractA long piece of magnetic material shaped as a central cylindrical wire (diameter $$d=50$$ d = 50 nm) with two wider coaxial cylindrical portions (diameter $$D=90$$ D = 90 nm and thickness $$t=100$$ t = 100 nm) defines a bimodulated nanowire. Micromagnetism is invoked to study the equilibrium energy of the system under the variations of the positions of the modulations along the wire. The system can be thought of as composed of five independent elements (3 segments and 2 modulations) leading to $$2^5=32$$ 2 5 = 32 possible different magnetic configurations, which will be later simplified to 4. We investigate the stability of the configurations depending on the positions of the modulations. The relative chirality of the modulations has negligible contributions to the energy and they have no effect on the stability of the stored configuration. However, the modulations are extremely important in pinning the domain walls that lead to consider each segment as independent from the rest. A phase diagram reporting the stability of the inscribed magnetic configurations is produced. The stability of the system was then tested under the action of external magnetic fields and it was found that more than 50 mT are necessary to alter the inscribed information. The main purpose of this paper is to find whether a prototype like this can be complemented to be used as a magnetic key or to store information in the form of firmware. Present results indicate that both possibilities are feasible.

Sign in / Sign up

Export Citation Format

Share Document