Effect of incoming boundary layer thickness on the flow dynamics of a square finite wall-mounted cylinder

2022 ◽  
Vol 34 (1) ◽  
pp. 015105
Author(s):  
Guang Chen ◽  
Xiao-Bai Li ◽  
Bo Sun ◽  
Xi-Feng Liang
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Flow Dynamics

EFFECTS OF BOUNDARY-LAYER THICKNESS ON UNSTEADY FLOW CHARACTERISTICS INSIDE OPEN CAVITIES AT SUBSONIC AND TRANSONIC SPEEDS

2012 ◽  
Vol 19 ◽  
pp. 206-213
Author(s):  
DANG-GUO YANG ◽  
JIAN-QIANG LI ◽  
ZHAO-LIN FAN ◽  
XIN-FU LUO
Keyword(s):  
Boundary Layer ◽  
Unsteady Flow ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Sound Pressure ◽  
Flow Characteristics ◽  
Open Cavity ◽  
Aerodynamic Noise ◽  
Sustained Oscillation ◽  
Cavity Depth

An experimental study was conducted in a 0.6m by 0.6m wind-tunnel to analyze effects of boundary-layer thickness on unsteady flow characteristics inside a rectangular open cavity at subsonic and transonic speeds. The sound pressure level (SPL) distributions at the centerline of the cavity floor and Sound pressure frequency spectrum (SPFS) characteristics on some measurement positions presented herein was obtained with cavity length-to-depth ratio (L/D) of 8 over Mach numbers (Ma) of 0.6 and 1.2 at a Reynolds numbers (Re) of 1.23 × 107 and 2.02 × 107 per meter under different boundary-layer thickness to cavity-depth ratios (δ/D). The experimental angle of attack, yawing and rolling angles were 0°. The results indicate that decrease in δ/D leads to severe flow separation and unsteady pressure fluctuation, which induces increase in SPL at same measurement points inside the cavity at Ma of 0.6. At Ma of 1.2, decrease in δ/D results in enhancing compressible waves. Generally, decrease in δ/D induces more flow self-sustained oscillation frequencies. It also makes severer aerodynamic noise inside the open cavity.

Boundary Layer Closure and Heat Transfer in Constant Base Pressure and Simple Wave Guns

1978 ◽  
Vol 100 (4) ◽  
pp. 690-696 ◽  
Author(s):  
A. D. Anderson ◽  
T. J. Dahm
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Method Of Characteristics ◽  
Simple Wave ◽  
Momentum Equation ◽  
Base Pressure ◽  
Two Dimensional ◽  
The Method Of Characteristics

Solutions of the two-dimensional, unsteady integral momentum equation are obtained via the method of characteristics for two limiting modes of light gas launcher operation, the “constant base pressure gun” and the “simple wave gun”. Example predictions of boundary layer thickness and heat transfer are presented for a particular 1 in. hydrogen gun operated in each of these modes. Results for the constant base pressure gun are also presented in an approximate, more general form.

The structure of a highly decelerated axisymmetric turbulent boundary layer

2021 ◽  
Vol 929 ◽  
Author(s):  
N. Agastya Balantrapu ◽  
Christopher Hickling ◽  
W. Nathan Alexander ◽  
William Devenport
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Shear Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Large Scale ◽  
Convection Velocity ◽  
Mean Flow ◽  
Mean Velocity ◽  
The Mean

Experiments were performed over a body of revolution at a length-based Reynolds number of 1.9 million. While the lateral curvature parameters are moderate ( $\delta /r_s < 2, r_s^+>500$ , where $\delta$ is the boundary layer thickness and r s is the radius of curvature), the pressure gradient is increasingly adverse ( $\beta _{C} \in [5 \text {--} 18]$ where $\beta_{C}$ is Clauser’s pressure gradient parameter), representative of vehicle-relevant conditions. The mean flow in the outer regions of this fully attached boundary layer displays some properties of a free-shear layer, with the mean-velocity and turbulence intensity profiles attaining self-similarity with the ‘embedded shear layer’ scaling (Schatzman & Thomas, J. Fluid Mech., vol. 815, 2017, pp. 592–642). Spectral analysis of the streamwise turbulence revealed that, as the mean flow decelerates, the large-scale motions energize across the boundary layer, growing proportionally with the boundary layer thickness. When scaled with the shear layer parameters, the distribution of the energy in the low-frequency region is approximately self-similar, emphasizing the role of the embedded shear layer in the large-scale motions. The correlation structure of the boundary layer is discussed at length to supply information towards the development of turbulence and aeroacoustic models. One major finding is that the estimation of integral turbulence length scales from single-point measurements, via Taylor's hypothesis, requires significant corrections to the convection velocity in the inner 50 % of the boundary layer. The apparent convection velocity (estimated from the ratio of integral length scale to the time scale), is approximately 40 % greater than the local mean velocity, suggesting the turbulence is convected much faster than previously thought. Closer to the wall even higher corrections are required.

Magnetohydrodynamics Williamson Fluid Comprising Gyrotactic Microorganisms Flows Through a Permeable Stretching Layer with Variable Fluid Properties

2020 ◽  
Vol 9 (4) ◽  
pp. 375-387
Author(s):  
Amit Parmar ◽  
Rakesh Choudhary ◽  
Krishna Agarwal
Keyword(s):  
Boundary Layer ◽  
Velocity Profile ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Schmidt Number ◽  
Gyrotactic Microorganisms ◽  
Williamson Fluid ◽  
Non Linear ◽  
Fluid Properties ◽  
Variable Prandtl Number

The present study shows the impacts of Williamson fluid with magnetohydrodynamics flow containing gyrotactic microorganisms under the variable fluid property past permeable stretching sheet. Variable Prandtl number, mass Schmidt number, and gyrotactic microorganisms Schmidt number were all considered. The momentum, energy, mass, and microorganism equations’ governing PDEs are converted into nonlinear coupled ODEs and numerically solved with the bvp4c solver using suitable transformations. The main outcome of this study is that Williamson fluid parameter constantly decreases in velocity profile, however reverse effects can be shown in temperature profile. Also, M parameter and Kp parameter enhance the heat transfer rate, concentration rate and microorganisms boundary layer thickness but declines in momentum boundary layer thickness and velocity profile. The aim of this research is to see how velocity slide, temperature jump, concentration slip, and microorganism slip affect MHD Williamson fluid flow with gyrotactic microorganisms over a leaky surface embedded in spongy medium, with non-linear radiation and non-linear chemical reaction.

Freestream Flow Effects on Film Effectiveness and Heat Transfer Coefficient Augmentation for Compound Angle Shaped Holes

2017 ◽  
Author(s):  
Joshua B. Anderson ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
Zachary Webster
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Layer Thickness ◽  
Film Cooling ◽  
Gas Turbines ◽  
Boundary Layer Thickness ◽  
Adiabatic Effectiveness ◽  
Compound Angle

The use of compound-angled shaped film cooling holes in gas turbines provides a method for cooling regions of extreme curvature on turbine blades or vanes. These configurations have received surprisingly little attention in the film cooling literature. In this study, a row of laid-back fanshaped holes based on an open-literature design, were oriented at a 45-degree compound angle to the approaching freestream flow. In this study, the influence of the approach flow boundary layer thickness and character were experimentally investigated. A trip wire and turbulence generator were used to vary the boundary layer thickness and freestream conditions from a thin laminar boundary layer flow to a fully turbulent boundary layer and freestream at the hole breakout location. Steady-state adiabatic effectiveness and heat transfer coefficient augmentation were measured using high-resolution IR thermography, which allowed the use of an elevated density ratio of DR = 1.20. The results show adiabatic effectiveness was generally lower than for axially-oriented holes of the same geometry, and that boundary layer thickness was an important parameter in predicting effectiveness of the holes. Heat transfer coefficient augmentation was highly dependent on the freestream turbulence levels as well as boundary layer thickness, and significant spatial variations were observed.

scholarly journals Flow around a Finite Circular Cylinder on a Flat Plate : Cylinder height greater than turbulent boundary layer thickness

1984 ◽  
Vol 27 (232) ◽  
pp. 2142-2151 ◽  
Author(s):  
Takao KAWAMURA ◽  
Munehiko HIWADA ◽  
Toshiharu HIBINO ◽  
Ikuo MABUCHI ◽  
Masaya KUMADA
Keyword(s):  
Boundary Layer ◽  
Circular Cylinder ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Layer Thickness ◽  
Boundary Layer Thickness
Sign in / Sign up

Export Citation Format

Share Document