Boundary Layer Closure and Heat Transfer in Constant Base Pressure and Simple Wave Guns

1978 ◽  
Vol 100 (4) ◽  
pp. 690-696 ◽  
Author(s):  
A. D. Anderson ◽  
T. J. Dahm
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Method Of Characteristics ◽  
Simple Wave ◽  
Momentum Equation ◽  
Base Pressure ◽  
Two Dimensional ◽  
The Method Of Characteristics

Solutions of the two-dimensional, unsteady integral momentum equation are obtained via the method of characteristics for two limiting modes of light gas launcher operation, the “constant base pressure gun” and the “simple wave gun”. Example predictions of boundary layer thickness and heat transfer are presented for a particular 1 in. hydrogen gun operated in each of these modes. Results for the constant base pressure gun are also presented in an approximate, more general form.

Freestream Flow Effects on Film Effectiveness and Heat Transfer Coefficient Augmentation for Compound Angle Shaped Holes

2017 ◽  
Author(s):  
Joshua B. Anderson ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
Zachary Webster
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Layer Thickness ◽  
Film Cooling ◽  
Gas Turbines ◽  
Boundary Layer Thickness ◽  
Adiabatic Effectiveness ◽  
Compound Angle

The use of compound-angled shaped film cooling holes in gas turbines provides a method for cooling regions of extreme curvature on turbine blades or vanes. These configurations have received surprisingly little attention in the film cooling literature. In this study, a row of laid-back fanshaped holes based on an open-literature design, were oriented at a 45-degree compound angle to the approaching freestream flow. In this study, the influence of the approach flow boundary layer thickness and character were experimentally investigated. A trip wire and turbulence generator were used to vary the boundary layer thickness and freestream conditions from a thin laminar boundary layer flow to a fully turbulent boundary layer and freestream at the hole breakout location. Steady-state adiabatic effectiveness and heat transfer coefficient augmentation were measured using high-resolution IR thermography, which allowed the use of an elevated density ratio of DR = 1.20. The results show adiabatic effectiveness was generally lower than for axially-oriented holes of the same geometry, and that boundary layer thickness was an important parameter in predicting effectiveness of the holes. Heat transfer coefficient augmentation was highly dependent on the freestream turbulence levels as well as boundary layer thickness, and significant spatial variations were observed.

Boundary-layer thickness and base pressure

AIAA Journal ◽  
1985 ◽  
Vol 23 (12) ◽  
pp. 1987-1989 ◽  
Author(s):  
Mauri Tanner
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Base Pressure

Heat Transfer Around a Cylindrical Protuberance Mounted in a Plane Turbulent Boundary Layer

2005 ◽  
Vol 128 (2) ◽  
pp. 153-161 ◽  
Author(s):  
Takayuki Tsutsui ◽  
Masafumi Kawahara
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Aspect Ratio ◽  
Turbulent Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Reynolds Numbers ◽  
Heat Transfer Characteristics ◽  
Low Aspect Ratio ◽  
Maximum Value

Heat transfer characteristics around a low aspect ratio cylindrical protuberance placed in a turbulent boundary layer were investigated. The diameters of the protuberance, D, were 40 and 80mm, and the height to diameter aspect ratio H∕D ranged from 0.125 to 1.0. The Reynolds numbers based on D ranged from 1.1×104 to 1.1×105 and the thickness of the turbulent boundary layer at the protuberance location, δ, ranged from 26 to 120mm for these experiments. In this paper we detail the effects of the boundary layer thickness and the protuberance aspect ratio on heat transfer. The results revealed that the overall heat transfer for the cylindrical protuberance reaches a maximum value when H∕δ=0.24.

Effect of Sound on Heat Transfer from a Horizontal Circular Cylinder at Large Wavelengths

1965 ◽  
Vol 7 (2) ◽  
pp. 127-130 ◽  
Author(s):  
B. H. Lee ◽  
P. D. Richardson
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Circular Cylinder ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Sound Field ◽  
Practical Relevance ◽  
Local Effects ◽  
Horizontal Circular Cylinder ◽  
Standing Sound

The practical relevance of investigations of the effect of oscillations on convective heat transfer is discussed. Some experiments on overall heat transfer from a horizontal heated circular cylinder in a transverse, horizontal standing sound field are reported. Observations of local effects of sound on boundary layer thickness and heat transfer are described, and a correlation of heat transfer spanning all sound intensities is suggested in the light of these observations. The correlation is fitted well by the data, and thus provides adducive evidence for the explanation of the phenomena observed.

Melting heat transfer in the stagnation-point flow of Maxwell fluid with double-diffusive convection

2014 ◽  
Vol 24 (3) ◽  
pp. 760-774 ◽  
Author(s):  
Tasawar Hayat ◽  
Muhammad Farooq ◽  
Ahmad Alsaedi
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Velocity Profile ◽  
Layer Thickness ◽  
Stagnation Point ◽  
Boundary Layer Thickness ◽  
Double Diffusive Convection ◽  
Content Type ◽  
Diffusive Convection ◽  
Double Diffusive

Purpose – The purpose of this paper is to analyze the melting heat transfer in the stagnation-point flow with double-diffusive convection. Design/methodology/approach – Series solutions for velocity, temperature and concentration are constructed via homotopy analysis method. Findings – The authors observed that the behaviors of N, ?2 and M on the velocity and boundary layer thickness are qualitatively similar. Further, for A<1 the velocity profile and boundary layer thickness increase with the increase of A. However, when A>1 then the velocity profile increases but the boundary layer thickness decreases when A is increased. Originality/value – This analysis has not been discussed in the literature previously.

Sign in / Sign up

Export Citation Format

Share Document