scholarly journals Room temperature deposition of superconducting niobium nitride films by ion beam assisted sputtering

APL Materials ◽  
2018 ◽  
Vol 6 (7) ◽  
pp. 076107 ◽  
Author(s):  
Tomas Polakovic ◽  
Sergi Lendinez ◽  
John E. Pearson ◽  
Axel Hoffmann ◽  
Volodymyr Yefremenko ◽  
...  
Keyword(s):  
Room Temperature ◽  
Ion Beam ◽  
Niobium Nitride ◽  
Temperature Deposition

Biaxially Textured Buffer Layers on Large-Area Polycrystalline Substrates

1999 ◽  
Vol 585 ◽  
Author(s):  
J. Dzick ◽  
S. Sievers ◽  
J. Hoffmann ◽  
K. Thiele ◽  
F. Garcia-Moreno ◽  
...  
Keyword(s):  
Room Temperature ◽  
Ion Beam ◽  
Thermal Contact ◽  
Deposition Process ◽  
Ion Sources ◽  
Buffer Layers ◽  
Large Area ◽  
Ybco Films ◽  
Ion Beam Assisted Deposition ◽  
Temperature Deposition

AbstractBiaxially textured yttria stabilized zirconia (YSZ) buffer layers were deposited on long polycrystalline metallic tapes by an ion-beam-assisted deposition process (IBAD) to serve as templates for high-current carrying Y1Ba2Cu3O7-x (YBCO) films. YSZ was deposited by a dualionbeam equipment with two 11 cm Kaufman ion sources. The coating of large-area technical substrates, large in comparison with the ion sources, requires substrate movements to render YSZ films of homogeneous texture quality. These movements can hinder cooling of the metallic tapes in the absence of a thermal contact. Therefore, the temperature of those small-heat-capacity substrates could rise to above 100 °C within minutes, causing a decrease of the in-plane alignment of YSZ. The investigation of the temperature dependence of the IBAD process reveals that the best results of the in-plane alignment could be obtained by room temperature deposition. Applying high tape velocities hinder a rise of the deposition temperature to above 90 °C. Therefore, it is possible to deposit YSZ films on metal tapes (up to 60 mm × 1000 mm) with in-plane textures down to 15° full width at half maximum (FWHM), which allow their coating with highcurrent-carrying YBCO films.

Nanocomposite Polyurethane Foams Via POSS Blends

2002 ◽  
Vol 733 ◽  
Author(s):  
Brock McCabe ◽  
Steven Nutt ◽  
Brent Viers ◽  
Tim Haddad
Keyword(s):  
High Temperature ◽  
Sample Preparation ◽  
Room Temperature ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Polyurethane Foams ◽  
Development Projects ◽  
Polymer Systems ◽  
Polyurethane Resin ◽  
Military Development

AbstractPolyhedral Oligomeric Silsequioxane molecules have been incorporated into a commercial polyurethane formulation to produce nanocomposite polyurethane foam. This tiny POSS silica molecule has been used successfully to enhance the performance of polymer systems using co-polymerization and blend strategies. In our investigation, we chose a high-temperature MDI Polyurethane resin foam currently used in military development projects. For the nanofiller, or “blend”, Cp7T7(OH)3 POSS was chosen. Structural characterization was accomplished by TEM and SEM to determine POSS dispersion and cell morphology, respectively. Thermal behavior was investigated by TGA. Two methods of TEM sample preparation were employed, Focused Ion Beam and Ultramicrotomy (room temperature).

Compression of Single-Crystal Micropillars of the Γ Intermetallic Phase in the Fe-Zn System

2014 ◽  
Vol 922 ◽  
pp. 264-269 ◽  
Author(s):  
Masahiro Inomoto ◽  
Norihiko L. Okamoto ◽  
Haruyuki Inui
Keyword(s):  
Single Crystal ◽  
Deformation Behavior ◽  
Room Temperature ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Intermetallic Phase ◽  
Gamma Phase ◽  
Compression Tests ◽  
Slip Direction ◽  
Beam Method

The deformation behavior of the Γ (gamma) phase in the Fe-Zn system has been investigated via room-temperature compression tests of single-crystal micropillar specimens fabricated by the focused ion beam method. Trace analysis of slip lines indicates that {110} slip occurs for the specimens investigated in the present study. Although the slip direction has not been uniquely determined, the slip direction might be <111> in consideration of the crystal structure of the Γ phase (bcc).

AFM Study of Surface Morphology of Aluminum Nitride Thin Films

1995 ◽  
Vol 388 ◽  
Author(s):  
Yoshihisa Watanabe ◽  
Yoshikazu Nakamura ◽  
Shigekazu Hirayama ◽  
Yuusaku Naota
Keyword(s):  
Thin Films ◽  
Surface Morphology ◽  
Substrate Temperature ◽  
Single Crystal ◽  
Room Temperature ◽  
Ion Beam ◽  
Soda Lime ◽  
Silicon Single Crystal ◽  
Soda Lime Glass ◽  
Average Roughness

AbstractAluminum nitride (AlN) thin films have been synthesized by ion-beam assisted deposition method. Film deposition has been performed on the substrates of silicon single crystal, soda-lime glass and alumin A. the influence of the substrate roughness on the film roughness is studied. the substrate temperature has been kept at room temperature and 473K and the kinetic energy of the incident nitrogen ion beam and the deposition rate have been fixed to 0.5 keV and 0.07 nm/s, respectively. the microstructure of the synthesized films has been examined by X-ray diffraction (XRD) and the surface morphology has been observed by atomic force microscopy(AFM). IN the XRD patterns of films synthesized at both room temperature and 473K, the diffraction line indicating the alN (10*0) can be discerned and the broad peak composed of two lines indicating the a1N (00*2) and a1N (10*1) planes is also observed. aFM observations for 100 nm films reveal that (1) the surface of the films synthesized on the silicon single crystal and soda-lime glass substrates is uniform and smooth on the nanometer scale, (2) the average roughness of the films synthesized on the alumina substrate is similar to that of the substrate, suggesting the evaluation of the average roughness of the film itself is difficult in the case of the rough substrate, and (3) the average roughness increases with increasing the substrate temperature.

Sign in / Sign up

Export Citation Format

Share Document