A novel low cost pulse excitation source to study trap spectroscopy of persistent luminescent materials

2018 ◽  
Author(s):  
Ngangbam Chandrasekhar ◽  
Nungleppam Monorajan Singh ◽  
R. K. Gartia
Keyword(s):  
Low Cost ◽  
Excitation Source ◽  
Pulse Excitation ◽  
Luminescent Materials

A NOVEL NANOFABRICATION USING MICRO DROPLET JETTING SYSTEM

2006 ◽  
Vol 05 (06) ◽  
pp. 809-813
Author(s):  
XIAORAN LI ◽  
JUN XU ◽  
LEI ZHAO ◽  
XIAO GUO ◽  
WEI HUANG
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
High Stability ◽  
High Reliability ◽  
Low Cost ◽  
Luminescent Materials ◽  
Patterned Surface ◽  
Characteristic Wavelength ◽  
Micro Topography ◽  
Scanning Electron

This study briefly reports a newly developed nanopatterning technology utilizing a so-called micro droplet jetting system, which can be used in various applications such as nanofabrication. Compared with the conventional methods, this technology has the advantages as follows: it can be manipulated easily and patterned freely as the user requires; furthermore, it shows high-reliability and high-stability with very low cost. The typical specs of the micro droplet jetting system for fabricating nanodevice show as follows: (1) nanoparticle size: 50–60 nm; (2) characteristic wavelength: 400–450 nm; (3) volume of droplet: 6 ppl; (4) size of pixel: 70 μm. In this article, the nanopatterning technology adopting the micro droplet jetting system has been demonstrated to be useful for nanopatterning the pixels which consist of nanoparticles, organic luminescent materials. In addition, the micro topography and the luminescent property of the patterned surface have been characterized by using Scanning Electron Microscope (SEM) and fluorescence microscope, respectively. Finally, the fluorescence of the patterned nanoparticles was observed.

All solid state pulse excitation source for kHz excimer laser

2013 ◽  
Vol 25 (4) ◽  
pp. 885-559 ◽  
Author(s):  
王庆胜 Wang Qingsheng ◽  
游利兵 You Libing ◽  
余吟山 Yu Yinshan ◽  
赵家敏 Zhao Jiamin ◽  
方晓东 Fang Xiaodong
Keyword(s):  
Solid State ◽  
Excimer Laser ◽  
Excitation Source ◽  
Pulse Excitation

Multipath Exciton Harvesting in Diazine-based Luminescent Materials and Their Applications for Organic Light-Emitting Diodes

2021 ◽  
Author(s):  
Ling Yu ◽  
Chuluo Yang
Keyword(s):  
Low Cost ◽  
Recent Decade ◽  
Delayed Fluorescence ◽  
Device Fabrication ◽  
Organic Light Emitting Diodes ◽  
Luminescent Materials ◽  
Thermally Activated Delayed Fluorescence ◽  
Light Emitting ◽  
Thermally Activated ◽  
Organic Light

Thermally activated delayed fluorescence (TADF) materials have attracted intensive interests in recent decade owing to their intrinsic merits of 100% exciton collection capability and relatively low-cost device fabrication. An abundance...

Decomposition of the metastable beta titanium alloy Ti-15-3

1983 ◽  
Vol 41 ◽  
pp. 264-265
Author(s):  
Y. L. Chen ◽  
S. Fujlshiro
Keyword(s):  
Low Cost ◽  
High Strength ◽  
Alpha Phase ◽  
Thick Sheet ◽  
Omega Phase ◽  
Beta Titanium Alloy ◽  
Beta Titanium ◽  
Beta Matrix ◽  
Metastable Beta ◽  
Very High

Metastable beta titanium alloys have been known to have numerous advantages such as cold formability, high strength, good fracture resistance, deep hardenability, and cost effectiveness. Very high strength is obtainable by precipitation of the hexagonal alpha phase in a bcc beta matrix in these alloys. Precipitation hardening in the metastable beta alloys may also result from the formation of transition phases such as omega phase. Ti-15-3 (Ti-15V- 3Cr-3Al-3Sn) has been developed recently by TIMET and USAF for low cost sheet metal applications. The purpose of the present study was to examine the aging characteristics in this alloy.The composition of the as-received material is: 14.7 V, 3.14 Cr, 3.05 Al, 2.26 Sn, and 0.145 Fe. The beta transus temperature as determined by optical metallographic method was about 770°C. Specimen coupons were prepared from a mill-annealed 1.2 mm thick sheet, and solution treated at 827°C for 2 hr in argon, then water quenched. Aging was also done in argon at temperatures ranging from 316 to 616°C for various times.

Chromic Acid Etching of Polyethylene

1973 ◽  
Vol 31 ◽  
pp. 72-73
Author(s):  
J. D. Muzzy ◽  
R. D. Hester ◽  
J. L. Hubbard
Keyword(s):  
Chromic Acid ◽  
Low Cost ◽  
Acid Etching ◽  
Crystalline Morphology ◽  
Bulk Specimen ◽  
Morphological Studies ◽  
Perfect Form ◽  
Molecular Length ◽  
Lamellar Texture ◽  
Cost Studies

Polyethylene is one of the most important plastics produced today because of its good physical properties, ease of fabrication and low cost. Studies to improve the properties of polyethylene are leading to an understanding of its crystalline morphology. Polyethylene crystallized by evaporation from dilute solutions consists of thin crystals called lamellae. The polyethylene molecules are parallel to the thickness of the lamellae and are folded since the thickness of the lamellae is much less than the molecular length. This lamellar texture persists in less perfect form in polyethylene crystallized from the melt.Morphological studies of melt crystallized polyethylene have been limited due to the difficulty of isolating the microstructure from the bulk specimen without destroying or deforming it.

Glass Knife Geometry as Seen by the SEM

1971 ◽  
Vol 29 ◽  
pp. 454-455
Author(s):  
J. Temple Black
Keyword(s):  
Low Cost ◽  
Amorphous Material ◽  
Stress Concentrations ◽  
Basic Tool ◽  
Tool Materials ◽  
Optical Inspection ◽  
Surface Flaws ◽  
Slip Planes ◽  
Glass Knife ◽  
Diamond Knife

In ultramicrotomy, the two basic tool materials are glass and diamond. Glass because of its low cost and ease of manufacture of the knife itself is still widely used despite the superiority of diamond knives in many applications. Both kinds of knives produce plastic deformation in the microtomed section due to the nature of the cutting process and microscopic chips in the edge of the knife. Because glass has no well defined slip planes in its structure (it's an amorphous material), it is very strong and essentially never fails in compression. However, surface flaws produce stress concentrations which reduce the strength of glass to 10,000 to 20,000 psi from its theoretical or flaw free values of 1 to 2 million psi. While the microchips in the edge of the glass or diamond knife are generally too small to be observed in the SEM, the second common type of defect can be identified. This is the striations (also termed the check marks or feathers) which are always present over the entire edge of a glass knife regardless of whether or not they are visable under optical inspection. These steps in the cutting edge can be observed in the SEM by proper preparation of carefully broken knives and orientation of the knife, with respect to the scanning beam.

Spectraplot: A PC-based spectrum translation and display program

1988 ◽  
Vol 46 ◽  
pp. 918-919
Author(s):  
H. O. Colijn
Keyword(s):  
Low Cost ◽  
Transfer Program ◽  
File Transfer ◽  
Transfer Data ◽  
Error Checking ◽  
Data Files ◽  
The University

Many labs today wish to transfer data between their EDS systems and their existing PCs and minicomputers. Our lab has implemented SpectraPlot, a low- cost PC-based system to allow offline examination and plotting of spectra. We adopted this system in order to make more efficient use of our microscopes and EDS consoles, to provide hardcopy output for an older EDS system, and to allow students to access their data after leaving the university.As shown in Fig. 1, we have three EDS systems (one of which is located in another building) which can store data on 8 inch RT-11 floppy disks. We transfer data from these systems to a DEC MINC computer using “SneakerNet”, which consists of putting on a pair of sneakers and running down the hall. We then use the Hermit file transfer program to download the data files with error checking from the MINC to the PC.

Sign in / Sign up

Export Citation Format

Share Document