Numerical solutions of sheath structures around a moderate negative biased electron-emitting cylindrical probe in low-density isotropic plasma

2017 ◽  
Vol 24 (9) ◽  
pp. 093509 ◽  
Author(s):  
Alif Din
Keyword(s):  
Numerical Solutions ◽  
Low Density ◽  
Isotropic Plasma ◽  
Cylindrical Probe

Application of Improved Voltage Compensation in the SEM to Imaging of Organic Materials

1973 ◽  
Vol 31 ◽  
pp. 444-445
Author(s):  
P.J. Killingworth ◽  
M. Warren
Keyword(s):  
Electron Beam ◽  
Organic Materials ◽  
Operating Parameters ◽  
Low Density ◽  
Beam Diameter ◽  
Incident Electron Beam ◽  
Specimen Material ◽  
Voltage Compensation ◽  
Selection Of ◽  
Scanning Electron

Ultimate resolution in the scanning electron microscope is determined not only by the diameter of the incident electron beam, but by interaction of that beam with the specimen material. Generally, while minimum beam diameter diminishes with increasing voltage, due to the reduced effect of aberration component and magnetic interference, the excited volume within the sample increases with electron energy. Thus, for any given material and imaging signal, there is an optimum volt age to achieve best resolution.In the case of organic materials, which are in general of low density and electric ally non-conducting; and may in addition be susceptible to radiation and heat damage, the selection of correct operating parameters is extremely critical and is achiev ed by interative adjustment.

Quantitative defect studies in semiconductor TEM samples prepared by low angle ion milling

1995 ◽  
Vol 53 ◽  
pp. 512-513
Author(s):  
L. Mulestagno ◽  
J.C. Holzer ◽  
P. Fraundorf
Keyword(s):  
Sample Preparation ◽  
Milling Time ◽  
High Density ◽  
Low Density ◽  
Ion Milling ◽  
High Quality ◽  
Variable Angle ◽  
Major Disadvantage ◽  
Induced Defects

Due to the wealth of information, both analytical and structural that can be obtained from it TEM always has been a favorite tool for the analysis of process-induced defects in semiconductor wafers. The only major disadvantage has always been, that the volume under study in the TEM is relatively small, making it difficult to locate low density defects, and sample preparation is a somewhat lengthy procedure. This problem has been somewhat alleviated by the availability of efficient low angle milling.Using a PIPS® variable angle ion -mill, manufactured by Gatan, we have been consistently obtaining planar specimens with a high quality thin area in excess of 5 × 104 μm2 in about half an hour (milling time), which has made it possible to locate defects at lower densities, or, for defects of relatively high density, obtain information which is statistically more significant (table 1).

Intralysosomal Accumulation of Colloidal Gold-Low Density Lipoprotein Conjugates in Chloroquine-Treated Fibroblasts

1985 ◽  
Vol 43 ◽  
pp. 546-547 ◽  
Author(s):  
Dean A. Handley ◽  
Cynthia M. Arbeeny ◽  
Larry D. Witte
Keyword(s):  
Colloidal Gold ◽  
Cultured Cells ◽  
Low Density Lipoprotein ◽  
Density Lipoprotein ◽  
Coated Vesicle ◽  
Low Density ◽  
Cholesterol Esters ◽  
Cultured Fibroblasts ◽  
Surface Receptors ◽  
Ldl Particles

Low density lipoproteins (LDL) are the major cholesterol carrying particles in the blood. Using cultured cells, it has been shown that LDL particles interact with specific surface receptors and are internalized via a coated pit-coated vesicle pathway for lysosomal catabolism. This (Pathway has been visualized using LDL labeled to ferritin or colloidal gold. It is now recognized that certain lysomotropic agents, such as chloroquine, inhibit lysosomal enzymes that degrade protein and cholesterol esters. By interrupting cholesterol ester hydrolysis, chloroquine treatment results in lysosomal accumulation of cholesterol esters from internalized LDL. Using LDL conjugated to colloidal gold, we have examined the ultrastructural effects of chloroquine on lipoprotein uptake by normal cultured fibroblasts.

ALCHEMI of B2-Ordered Fe50Al45Me5 alloys

1996 ◽  
Vol 54 ◽  
pp. 548-549
Author(s):  
Ian M. Anderson
Keyword(s):  
Room Temperature ◽  
Iron Aluminide ◽  
Low Density ◽  
Intermetallic Alloys ◽  
Practical Applications ◽  
Alloying Additions ◽  
Site Distribution ◽  
Good Corrosion Resistance ◽  
Room Temperature Ductility ◽  
The Matrix

B2-ordered iron aluminide intermetallic alloys exhibit a combination of attractive properties such as low density and good corrosion resistance. However, the practical applications of these alloys are limited by their poor fracture toughness and low room temperature ductility. One current strategy for overcoming these undesirable properties is to attempt to modify the basic chemistry of the materials with alloying additions. These changes in the chemistry of the material cannot be fully understood without a knowledge of the site-distribution of the alloying elements. In this paper, the site-distributions of a series of 3d-transition metal alloying additions in B2-ordered iron aluminides are studied with ALCHEMI.A series of seven alloys of stoichiometry Fe50AL45Me5, with Me = {Ti, V, Cr, Mn, Co, Ni, Cu}, were prepared with identical heating cycles. Microalloying additions of 0.2% B and 0.1% Zr were also incorporated to strengthen the grain boundaries, but these alloying additions have little influence on the matrix chemistry and are incidental to this study.

Characterization of machined polystyrene foam

1989 ◽  
Vol 47 ◽  
pp. 372-373
Author(s):  
C. W. Price ◽  
E. F. Lindsey ◽  
R. M. Franks ◽  
M. A. Lane
Keyword(s):  
Surface Finish ◽  
Cell Walls ◽  
Surface Structures ◽  
Efficient Technique ◽  
Low Density ◽  
Polystyrene Foam ◽  
Planar Surfaces ◽  
Machining Characteristics

Diamond-point turning is an efficient technique for machining low-density polystyrene foam, and the surface finish can be substantially improved by grinding. However, both diamond-point turning and grinding tend to tear and fracture cell walls and leave asperities formed by agglomerations of fragmented cell walls. Vibratoming is proving to be an excellent technique to form planar surfaces in polystyrene, and the machining characteristics of vibratoming and diamond-point turning are compared.Our work has demonstrated that proper evaluation of surface structures in low density polystyrene foam requires stereoscopic examinations; tilts of + and − 3 1/2 degrees were used for the stereo pairs. Coating does not seriously distort low-density polystyrene foam. Therefore, the specimens were gold-palladium coated and examined in a Hitachi S-800 FESEM at 5 kV.

Atomic Imaging of Crystals using Large-Angle Electron Scattering in STEM

1990 ◽  
Vol 48 (1) ◽  
pp. 74-75
Author(s):  
D.E. Jesson ◽  
S. J. Pennycook
Keyword(s):  
Wave Function ◽  
Electron Scattering ◽  
Numerical Solutions ◽  
Large Angle ◽  
Real Space ◽  
High Angle ◽  
Analytical Treatment ◽  
Order Zero ◽  
Experimental Conditions ◽  
Ewald Sphere

It is well known that conventional atomic resolution electron microscopy is a coherent imaging process best interpreted in reciprocal space using contrast transfer function theory. This is because the equivalent real space interpretation involving a convolution between the exit face wave function and the instrumental response is difficult to visualize. Furthermore, the crystal wave function is not simply related to the projected crystal potential, except under a very restrictive set of experimental conditions, making image simulation an essential part of image interpretation. In this paper we present a different conceptual approach to the atomic imaging of crystals based on incoherent imaging theory. Using a real-space analysis of electron scattering to a high-angle annular detector, it is shown how the STEM imaging process can be partitioned into components parallel and perpendicular to the relevant low index zone-axis.It has become customary to describe STEM imaging using the analytical treatment developed by Cowley. However, the convenient assumption of a phase object (which neglects the curvature of the Ewald sphere) fails rapidly for large scattering angles, even in very thin crystals. Thus, to avoid unpredictive numerical solutions, it would seem more appropriate to apply pseudo-kinematic theory to the treatment of the weak high angle signal. Diffraction to medium order zero-layer reflections is most important compared with thermal diffuse scattering in very thin crystals (<5nm). The electron wave function ψ(R,z) at a depth z and transverse coordinate R due to a phase aberrated surface probe function P(R-RO) located at RO is then well described by the channeling approximation;

Sign in / Sign up

Export Citation Format

Share Document